• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.11
• /
• pp.1633-1640
• /
• 2013

In this paper, noise parameters for high frequency modeling of dual-gate FET are extracted and analyzed. To extract thermal noise parameter of dual gate, noise characteristics are measured by changing input impedance of noise source using Tuner, and the influence of pad parasitic elements are subtracted using open and short dummy structure. Measured results indicated that the dual-gate FET is improved the noise figure by 0.2dB compared with conventional cascode structure FET at 5GHz, and it confirmed that the noise figure has dropped due to reduction of capacitances between the drain and source, gate and drain by simulation and analysis of small-signal parameters.

• Journal of the Korean Chemical Society
• /
• v.40 no.1
• /
• pp.37-43
• /
• 1996

The electrochemical impedance spectra of polyaniline film coated on tungsten electrodes by cyclic voltammetry have been measured in 0.1 M aqueous sulfuric acid solution. An electrochemical cell composed of large redox capacitance and low resistance of PANI-film in series was in agreement with the conductive behavior reported at these potentials. When the PANI was coated on bare tungsten, the electrolytic resistance was only observed. However, on the oxidized tungsten instead of bare tungsten, the resistance of tungsten oxide and the contact resistance between PANI and tungsten oxide were additionally observed. Equivalent electrical circuits have been deduced from the impedance data. It was therfore possible to obtain the parameters of the ionic mass transport within the film.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.9
• /
• pp.2505-2513
• /
• 1996

This paper presents the analysis of the impedance characteristic of the strip type waveguide mount backed by the dielectric substrate using mode the matching and induced EMF method. The part of the waveguide containing the dielectric substrate is modeled as waveguide partially filled with the dielectric, and a hybrid mode analysis has been conducted for the structure. The electromagnetic scattering problem by the dielectric substrate is solved by the mode matching method using the calculated modal function. The input impedance seen at the mount gap is calculated by the induced EMF method using the calculated results. the calculated results thus obtained has been verified through comparison with the results by other numerical methods. The effect of some structure parameters such as the width of the substrate and the gap size on the mount impedance is investigated.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.4
• /
• pp.648-662
• /
• 1996

Electrode surface reaction on glassy carbon and synthesized graphite (PVDF mixed graphite) in sulfuric acid solution is investigated by impedance spectroscopy at cyclic polarization. The redox peak, which may be due to the change of chemical adsorped functional group on electrode surface or oxidation and reduction of oxygen, is represented on glassy carbon and graphite electrode in potentio-dynamic current curve. The oxidation and reduction of these surface functional group on glassy carbon and PVDF mixed graphite have a major affect on the impedance spectrum and Faraday impedance parameter at cyclic polarization.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.12
• /
• pp.1084-1096
• /
• 2016

This paper presents method of design and analysis of a high-speed serial interface connector with a data rate of 12.5 Gbps. A high-speed serial interface connector is composed of various material and complex structures. It is very difficult to match the impedance of each discontinuous portion of connector. Therefore, this paper proposes the structure of a connector line that be simplified a connector. In the structure of proposed connector line, this research presents a method for extracting R, L, C and G parameters, analyzing the differential mode impedance, and minimizing the impedance discontinuity using time domain transmissometry and time domain reflectometry. This paper applies the proposed methods in the connector line to the high-speed serial interface connector. The proposed high-speed serial interface connector, which consists of forty-four pins, is analyzed signal transmission characteristics by changing the width and spacing of the four pins. According to the analysis result, as the width of the ground pin increases, the impedance decreases slightly. And as the distance between the ground pin and the signal pin increases, the impedance increases. In addition, as the width of the signal pin increases, the impedance decreases. And as the distance between the signal pin and the signal pin increases, the impedance decreases. The impedance characteristic of initial connector presents ranges from 96 to $139{\Omega}$. Impedance characteristic after applying the structure of proposed connector is shown as a value between 92.6 to $107.5{\Omega}$. This value satisfies the design objective $100{\Omega}{\pm}10%$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.7
• /
• pp.2541-2548
• /
• 2010

This paper describes the calculation for characteristic impedance of transmission line with periodic structures such as defected ground structure (DGS) and photonic bandgap (PBG). The previous method which uses the ${\lambda}$/4 transmission line model is reviewed and its disadvantage that the calculated characteristic impedance is strongly dependent on the frequency is discussed. The characteristic impedance of transmission lines with periodic structures are calculated using the ${\lambda}$/4 transmission line model and analytic method. The calculated characteristic impedance by the latter method is an almost constant value while that from the first method depends on the frequency strongly. In addition, the characteristic impedance of the transmission line with PBG is calculated and proposed, while it has been rarely studied ever. S-parameters are obtained from the measurement using the fabricated sample as well as simulation, and used for calculating the characteristic impedances and comparison. The characteristic impedances calculated from the measured S-parameters agree well with the simulated results. It is well described that the analytic method to calculate the characteristic impedance of transmission lines on uniform dielectric structures can be applied successfully to the transmission lines with periodic structures such as DGS and PBG.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.7
• /
• pp.387-392
• /
• 2019

A technique was researched to detect bolt looseness using a transfer impedance technique (the dual piezoelectric material technique) for monitoring the structural health of a bolt joint. In order to use the single piezoelectric material technique, an expensive impedance analyzer should be used. However, in the transfer impedance technique, low-cost fault detection can be performed using a general function generator and a digital multimeter. A steel plate frame test specimen composed of bolt joints was fabricated, and the tightening torques of the bolts were loosened step by step. By using the transfer impedance method, the damage index was obtained. It was found that the presence of faults could be reasonably estimated using the damage index, which increased with the degree of bolt looseness. An experiment was performed on the same specimen using the single piezoelectric material technique, and the results showed a similar tendency. It could be possible to estimate the damage of a bolt joint at low cost by eliminating the expensive impedance analyzer. This method could be used effectively for structural health monitoring after carrying out a study to estimate the fault location and severity.

• Proceedings of the KIPE Conference
• /
• 2012.11a
• /
• pp.181-182
• /
• 2012

마이크로그리드 계통 연계 운전시 분산 발전은 main grid와 함께 연계되어 부하의 수요를 담당한다. 하지만 계통사고나 의도적인 제어 전략으로 인해 분산 발전은 계통과 분리되어 단독으로 부하의 수요를 담당하게 된다. 이때 분산발전을 기반으로 한 인버터는 계통 연계 운전 시 하나의 전류원으로서의 역할을 하다가 시스템이 단독 운전 모드로 전환시 전압원으로 가정되게 된다. 이러한 특성으로 인해 단독운전 모드시의 인버터 병렬 운전은 시스템 파라미터와 라인 임피던스에 매우 민감해진다. 따라서 본 논문에서는 단독운전 모드시 불평형 저전압 마이크로그리드에서 대두되는 문제들에 대해 분석하고 가상 인덕터와 기준 전압 조정을 활용한 개선된 드룹 방식의 적용을 통해 이를 해결하고자 하였다. 제안된 이론은 PSIM 시뮬레이션을 통해 검증되었다.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.410-410
• /
• 2000

Impedance control is recognised as one of the most proper control scheme to carry out the assembly tasks, since it can control the dynamic relationship between the manipulator and environment directly. However, it is well known that the contact force cannot be controlled directly using the impedance control. Also impedance parameters should be properly defined depending on the task to be performed. We propose a new position based impedance control, which has self-adjusted impedance parameters and can control the contact force explicitly, Impedance parameters, as time-varying parameters, are adjusted automatically based on the measured contact force and the position error during the task. A proposed algorithm was implemented on the peg-in-hole task with the industrial manipulator. We shows the effectiveness of proposed control method experimentally.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.2
• /
• pp.689-692
• /
• 2005

Bioelectrical Impedance Analysis(BIA) can measure body water amount and then body fat mass. Locate 4 electrode in palm to measure efficiently and flow current(50kHz, 800uA) in body for measuring voltage and capacitance. And proposed method to measure body fat with hight, weight, age and distinction of sex.