• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.461-462
• /
• 2020

본 논문은 LCL 필터를 사용하는 계통연계형 인버터의 병렬운전 조건에서 LCL 필터와 계통 임피던스 간의 상호간섭에 따른 공진특성을 분석하였으며, 시뮬레이션 및 실험을 통해 검증하였다. 인버터 병렬운전은 2대 조건을 고려하였으며, LCL 필터를 포함한 시스템 파라미터는 동일 조건으로 설정하였다. PCC 지점에 인버터 병렬운전 조건 시, 계통 임피던스 존재로 인해 각 인버터의 LCL 필터 간 상호간섭 영향이 발생하며 필터 공진주파수의 이동은 인버터 병렬연결 수와 계통 임피던스 크기와의 연관성을 분석하였다. PSIM을 통해 시뮬레이션하고, MATLAB/SIMULINK 2018a를 통해 검증한다. 실시간 디지털 시뮬레이터와 DSP 28377 제어보드 연동을 통해 2대 인버터 병렬운전 조건에서의 상호간섭 특성을 실험하였으며, 분석결과와 동일한 실험결과를 도출함으로써 해석의 타당성을 검증하였다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.3
• /
• pp.401-408
• /
• 2001

This paper shows the design, fabrication and performance analysis of VCO which plays a major role in 5.8 GHz RF module for ITS. The design specifications of the VCO are determined on the basis of 5.8 GHz RF modul performance requirements. The design parameters are optimized through ADS simulation tool. The operating characteristic and performance analysis of the implemented VCO based on the design parameters are accomplished. The frequency variations according to the voltage change(0 ~5 V) of varactor diode are from 5.42 GHz to 5.518 GHz and the power level is 6.5 dBm. The second harmonic suppression are -21.5 dBc at 5.51 GHz and the phase noise characteristics are -83.81 dBc at 10 kHz offset frequency. The implemented VCO is available to not only DSRC and also, 5.8 GHz other systems.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.1
• /
• pp.133-143
• /
• 2001

This paper describes the correlation of the transient impedance and its parameters with the stationary resistance of a grounding system to a square pulse current and a lightning impulse current. In the experiment, the grounding system consists of a single grounding rod$(\Psi10[mm], 1[m])$and/or a triple-grounding rods of equilateral triangles with 5[m] spacing for operation. To analyze the transient impedance characteristics of the grounding system, a pulse generator which can produce square wave of a 30[ns] rise-time and a $20[\mus] $pulse duration is designed and fabricated. The injected content in the grounding system and the developed potential were recorded, and the time variation of the transient impedance were calculated as the ratio of the potential rising to the injected current at each time. The transient impedance and the effective surge impedance Z3 which defines economic protection level in power system were quite higher than the stationary resistance. The grounding impedance is decreased by the application of the triple-rods grounding system, and its effect is decreased as the frequency of the current is increased due to the inductance of the grounding leads.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.2
• /
• pp.47-53
• /
• 2013

In this work, signal transmission properties of SATA connector have been improved using its differential impedance calculation and its design revision to closer impedance matching. Using 3 dimensional electromagnetic field simulator, the differential mode S-parameter was calculated to investigate its signal fidelity. The differential impedance is calculated from the equation of the odd mode impedance with inductance, capacitance, mutual inductance, and mutual capacitance. The differential impedance of SATA connector was calculated to be $107.3{\Omega}$ and did not meet the design specification with $100{\Omega}{\pm}5%$. In order to achieve its impedance range and improve its signal transmission properties, SATA connector's design has been revised with two different directions and analyzed through the calculation of differential impedance, differential reflection loss, and differential insertion loss.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.11
• /
• pp.1248-1253
• /
• 2008

The MCS(Micro-Coplanar Strip) line with ground has been analyzed. The conformal mapping method is used to calculate the quasi-static effective dielectric constant and characteristic impedance of this MCS line. The computed results of the present work are found to be in good agreement when compared with the results obtained using commercial S/W, IE3D. And in this paper, the stepped-impedance low pass filter is designed and fabricated with MCS lines for improving the frequency responses. The LPF proposed structure has been also designed and implemented to have the sharp attenuation characteristics in stop band. The agreement between simulation and measurement results verify the implemented LPF.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.2
• /
• pp.39-49
• /
• 2012

An impedance bandwidth enhancement method of an aperture coupled microstrip patch antenna (ACMPA) using a shunt stub is investigated. The conventional ACMPA with a H-shaped coupling aperture is designed and the electrical parameters for the equivalent circuit of the designed conventional ACMPA are extracted. A method for the enhancement of the impedance bandwidth of the ACMPA using a tuning stub connected in shunt with the feed line is presented. The -10 dB return loss impedance bandwidth of the ACMPA with a shunt stub is increased up to about 14 %. The maximum impedance bandwidth of the corresponding ACMPA without a shunt stub is 5.4 %. The increase of the impedance bandwidth of the ACMPA with a shunt stub compared to that of the corresponding ACMPA without a shunt stub is about 160 %.

• Journal of Software Assessment and Valuation
• /
• v.15 no.1
• /
• pp.109-114
• /
• 2019

In this paper, simulations of S-parameter and characteristic impedance for the probe pin are performed and its high-frequency performance is analyzed. The probe pins are arranged with one signal pin in the center and four ground pins on the top, bottom, left and right sides. The insertion loss and return loss of the probe pin are calculated while increasing the separation between the probe pins to 0.35 mm, 0.40 mm, and 0.50 mm, respectively. It is confirmed that the probe pin has different features of the insertion loss due to its periodic resonance phenomenon. Effect of the characteristic impedance on pitch and assignment of the probe pin is also analyzed. It is verified that there are a number of ground pins whose characteristic impedance is close to 50 Ω.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.4
• /
• pp.73-80
• /
• 2013

In this paper, an experimental circuit model for an accurate high-frequency characterization of transmission line is proposed. Inherent resonance effects during measurements make it difficult to determine characteristic impedance and propagation constant at the resonance frequencies corresponding to the line length. Thus, resonance-effect-free transmission line parameter determination technique based on the physical insight and theory is proposed. Then, by using the parameters high-frequency circuit model is proposed for high-speed signal propagation characterization. The proposed frequency-variant transmission line model is verified with measurement and it can be usefully exploited in high-speed signal propagation characterization.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.11
• /
• pp.1034-1046
• /
• 2011

In this paper, a design and fabrication of 40 W power amplifier for the X-band using load-pull measurement of GaN HEMT chip are presented. The adopted active device for power amplifier is GaN HEMT chip of TriQuint company, which is recently released. Pre-matched fixtures are designed in test jig, because the impedance range of load-pull tuner is limited at measuring frequency. Essentially required 2-port S-parameters of the fixtures for extraction optimal input and output impedances is obtained by the presented newly method. The method is verified in comparison of the extracted optimal impedances with data sheet. The impedance matching circuit for power amplifier is designed based on EM co-simulation using the optimal impedances. The fabricated power amplifier with 15${\times}$17.8 $mm^2$ shows the efficiency above 35 %, the power gain of 8.7~8.3 dB and the output power of 46.7~46.3 dBm at 9~9.5 GHz with pulsed-driving width of 10 usec and duty of 10 %.

• Journal of the Korean Magnetics Society
• /
• v.8 no.6
• /
• pp.388-394
• /
• 1998

We designed and fabricated an improved null-type torque magnetometer for measuring magnetic anisotropy of magnetic materials. This torque magnetometer has a measurement range of $~{\pm}15$ dyne.cm, and the range can be controlled. Resolution is ~0.0005 dyne.cm. Noise level is less than 0.01 dyne.cm with one measurement, and less than 0.004 dyne.cm with 10 averaged measuremets. The precision is less than 0.5 %. In contrast to typical null-type torque magnetometers, we placed a small ferrite magnet in the Helmholtz coil, instead of placing coil in the permanent magnet. From this novel sturucture, we can design a geometrically isotropic and relatively light-weight sample rod. Also, we can prevent the effect of input and output lines of coil exposed in the magnetic field in torque meter. Consequently, our novel null-type torque magnetometer can have a better sensitivity, faster response time, and smaller distortion of torque curve than commercially available torque magnetometers.