• Journal of the Mineralogical Society of Korea
• /
• v.15 no.3
• /
• pp.195-204
• /
• 2002

Mineralogy and the exposed surface area are two of the most important factors controlling dissolution and weathering rates of soils. The mixture of inorganic and organic materials of various size distributions and structures that constitute soils makes the calculation of weathering rates difficult. The surface area of soil minerals plays an important role in most of programs for calculating the weathering rates and critical loads. The Brunauer-Emmett-Teller (BET) measurement is recommended for the measurement of specific surface area. However, BET values measured without organic matter removal are in fact those far all the N2-adsorbed surface areas, including the surfaces covered and aggregated with organisms. Surfaces occupied by organisms are assumed to be more reactive to weathering by organic activities. Therefore, the BET surface area difference before and after organic removal depicts the area occupied by organisms. The present study shows that the BET values after organic matter removal using $H_2$O$_2$ are larger than those without removal by 1.68~4.87 $m^2$/g. This implies that BET measurement without organic removal excludes the reactive area occupied by organisms and that the area occupied by organisms in soils is much larger than expected. It is suggested that specific surface area measurement for calculating weathering rates of mineral soils should be made before and after organic matter removal. The results of a column experiment are presented to demonstrate the potential retarding influence that this organic matter may have on mineral dissolution and weathering.

• Nuclear Engineering and Technology
• /
• v.26 no.1
• /
• pp.126-139
• /
• 1994

Best-estimate thermal-hydraulic codes, CATHARE2 V1.2 and RELAP5/MOD3, hate been assessed against the BETHSY 6.2 tc six-inch cold leg break loss-of-coolant accident (LOCA) test. Main objective is to analyze the overall capabilities of the two codes on physical phenomena of concern during the small break LOCA i.e. two-phase critical flow, depressurization, core water level de-pression, loop seal clearing, liquid holdup, etc. The calculation results show that the too codes predict well both in the occurrences and trends of major two-phase flow phenomena observed. Especially, the CATHARE2 calculations show better agreements with the experimental data. However, the two codes, in common, show some deviations in the predictions of loop seal clearing, collapsed core water level after the loop seal clearing, and accumulator injection behaviors. The discrepancies found from the comprision with the experimental data are larger in the RELAP5 results than in the CATHARE2. To analyze the deviations of the two code predictions in detail, several sensitivity calculations have been performed. In addition to the change of two-phase discharge coefficients for the break junction, fine nodalization and some corrections of the interphase drag term are made. For CATHARE2, the change of interphase drag force improves the mass distribution in the primary side. And the prediction of SG pressure is improved by the modification of boundary conditions. For RELAP5, any single input change doesn't improve the whole result and it is found that the interphase drag model has still large uncertainties.

• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.9
• /
• pp.469-475
• /
• 2016

The study is the result of an practical operation analysis for the full scale fishery product wastewater treatment plant with immersed MBR (iMBR) process. Since fishery product industries show a wide range of wastewater generation by the season, design and operation of the equalization basin are very important factor. The aeration system for the equalization basin mixing can save the chemical consumption for followed system through the restriction of acid fermentation. The concentrations of wastewater primary DAF process treated were BOD 2,291 mg/L, $COD_{Mn}$ 530 mg/L, SS 256.8 mg/L, T-N 38 mg/L, T-P 13.5 mg/L respectively. It was considered that iMBR is the most efficient biological process for high salinity content wastewater since It is irrelevant to the capability of the sludge precipitation. SADp and SADm were 0.31, $26.5m^3/hr{\cdot}m^3$ respectively. In iMBR process, the critical F/M ratio was derived at 0.08~0.10 gBOD/gMLSS by analysing the correlations between MLSS, normalized TMP and temperature. The effluent concentrations were BOD 1.8 mg/L, $COD_{Mn}$ 12.4 mg/L, SS 1.0 mg/L, T-N 7.85 mg/L, T-P 0.1 mg/L and removal efficiencies were 99.9%, 97.6%, 96.3%, 95.7%, 97.8% respectively.

• The Journal of the Korea Contents Association
• /
• v.20 no.7
• /
• pp.379-391
• /
• 2020

The growth paradigm that has led Korea for the last few decades is now reaching its critical point. Rather than focusing on the outcomes created by severe competitions of individual companies, a growth based on win-win system and solidarity focusing on public interests is more called for. In this background, I would like to examine the concept of corporate publicness and what factors consist of it. The study aims to verify a causal relationship that corporate publicness affects the corporation's social responsibility and consumers' favorability and credulity toward the company, and looks for the possibility that corporate publicness is recognized as a corporation's substantive competitiveness and an important management activity for its sustainability. The results of the study shows that corporate publicness is composed of 5 dimensions: sincerity, activeness, pursuit of public interest, harmony, and community spirit. Then the study statistically verifies that corporate publicness significantly has a positive impact on the overall evaluation results of a corporation's social responsibility. Lastly, the study confirms that corporate publicness and socially responsible activity of a company have a positive influence overall on the attitude toward the corporate brand. Based on these results, an implication is drawn that strengthening corporate publicness and its practice in action should be emphasized for a corporation to keep making outstanding performances in a sustainable way.

• Journal of Korea Technology Innovation Society
• /
• v.10 no.2
• /
• pp.183-205
• /
• 2007

An investigation was undertaken of the optimal discriminant model for predicting the likelihood of insolvency in advance for medium-sized firms based on the technology evaluation. The explanatory variables included in the discriminant model were selected by both factor analysis and discriminant analysis using stepwise selection method. Five explanatory variables were selected in factor analysis in terms of explanatory ratio and communality. Six explanatory variables were selected in stepwise discriminant analysis. The effectiveness of linear discriminant model and logistic discriminant model were assessed by the criteria of the critical probability and correct classification rate. Result showed that both model had similar correct classification rate and the linear discriminant model was preferred to the logistic discriminant model in terms of criteria of the critical probability In case of the linear discriminant model with critical probability of 0.5, the total-group correct classification rate was 70.4% and correct classification rates of insolvent and solvent groups were 73.4% and 69.5% respectively. Correct classification rate is an estimate of the probability that the estimated discriminant function will correctly classify the present sample. However, the actual correct classification rate is an estimate of the probability that the estimated discriminant function will correctly classify a future observation. Unfortunately, the correct classification rate underestimates the actual correct classification rate because the data set used to estimate the discriminant function is also used to evaluate them. The cross-validation method were used to estimate the bias of the correct classification rate. According to the results the estimated bias were 2.9% and the predicted actual correct classification rate was 67.5%. And a threshold value is set to establish an in-doubt category. Results of linear discriminant model can be applied for the technology financing banks to evaluate the possibility of insolvency and give the ranking of the firms applied.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2003.11a
• /
• pp.65-68
• /
• 2003

본 논문에서는 가장 최근의 동영상 표준인 H.264에서 가변 블록 움직임 예측 시 인접한 블록과의 상관성을 분석하여 병합 절차를 추가함으로써 매크로블록의 최종 모드를 결정하는 시간을 줄이기 위한 알고리즘을 제안한다. H.264에서는 매크로블록의 모드를 결정하기 위하여 총 7가지 모드를 사용하여 움직임 예측은 실시함으로써 부호화 효율을 극대화시킨 반면 이러한 움직임 예측이 부호화기의 복잡도를 높이는 주요 요인으로 현재 커다란 단점으로 지적되고 있다. 본 논문에서는 $8{\times}8$ 움직임 예측이 끝난 후 인접한 두 블록 사이의 거리론 임계값(Threshold)과 비교하여 다음 모드의 움직임 예측의 실시 여부를 먼저 절정함으로써 필요한 움직임 예측에 소비되는 시간을 단축시켰다. 여기서 실험 조건으로 명시하고 있는 것은 대표적인 단일모드 중에서 수행 성능이 가장 좋은 $8{\times}8$ 모드를 기본모드로 사용하고 병합 시 $16{\times}16$ 모드 쪽으로 상향식(bottom-up) 방법의 병합을 수행해 나아간다 모의실험을 통해 수행 성능과 전체 부호화 시간 측면을 본 논문에서 제안한 방법과 4가지 모드인 $16{\times}16,\;16{\times}8,\;8{\times}16,\;8{\times}8$ 모드를 모두 사용한 경우, $8{\times}8$ 단일모드를 사용한 경우를 비교하였다. 실험 결과 $8{\times}8$ 단일모드보다 수행 성능이 향상되었으며, 시간 단축 면에서 제안한 방법이 4가지 모드인 $16{\times}16,\;16{\times}8,\;8{\times}16,\;8{\times}8$ 모드를 모두 사용한 경우와 $8{\times}8$ 단일모드를 사용한 경우보다 계산 시간이 감소하였음을 확인하였다.행중인 MoIM-Messge서버의 네트워크 모듈로 다중 쓰레드 소켓폴링 모델을 적용하였다.n rate compared with conventional face recognition algorithms. 아니라 실내에서도 발생하고 있었다. 정량한 8개 화합물 각각과 총 휘발성 유기화합물의 스피어만 상관계수는 벤젠을 제외하고는 모두 유의하였다. 이중 톨루엔과 크실렌은 총 휘발성 유기화합물과 좋은 상관성 (톨루엔 0.76, 크실렌, 0.87)을 나타내었다. 이 연구는 톨루엔과 크실렌이 총 휘발성 유기화합물의 좋은 지표를 사용될 있고, 톨루엔, 에틸벤젠, 크실렌 등 많은 휘발성 유기화합물의 발생원은 실외뿐 아니라 실내에도 있음을 나타내고 있다.>10)의 $[^{18}F]F_2$를 얻었다. 결론: $^{18}O(p,n)^{18}F$ 핵반응을 이용하여 친전자성 방사성동위원소 $[^{18}F]F_2$를 생산하였다. 표적 챔버는 알루미늄으로 제작하였으며 본 연구에서 연구된 $[^{18}F]F_2$가스는 친핵성 치환반응으로 방사성동위원소를 도입하기 어려운 다양한 방사성의 약품개발에 유용하게 이용될 수 있을 것이다.었으나 움직임 보정 후 영상을 이용하여 비교한 경우, 결합능 변화가 선조체 영역에서 국한되어 나타나며 그 유의성이 움직임 보정 전에 비하여 낮음을 알 수 있었다. 결론: 뇌활성화 과제 수행시에 동반되는 피험자의 머리 움직임에 의하여 도파민 유리가 과대평가되었으며 이는 이 연구에서 제안한 영상정합을 이용한 움직임 보정기법에 의해서 개선되었다. 답이 없는 문제, 문제 만들기, 일반화가 가능한 문제 등으로 보고, 수학적 창의성 중 특히 확산적 사고에 초점을 맞추어 개방형 문제가 확산적 사고의 요소인 유창성, 독창성, 유연성 등에 각각 어떤 영향을 미치는지 20주의 프로그램을 개발, 진행하여 그 효과를 검증하고자 한다. 개방형 문

• Korean Journal of Remote Sensing
• /
• v.27 no.5
• /
• pp.601-611
• /
• 2011

Land cover changes are occurring for a variety of reasons such as urbanization, infrastructure construction, desertification, drought, flood, and so on. Many researchers have studied the cause and effect of land cover changes, and also the methods for change detection. However, most of the detection methods are based on the dichotomy of "change" and "not change" according a threshold value. In this paper, we present a change detection method with the integration of probability, spatial autocorrelation, and hotspot detection. We used the AMOEBA (A Multidirectional Ecotope-Based Algorithm) and developed the AMOEBA-CH (core hotspot) because the original algorithm tends to produce too many clusters. Our method considers the probability of land cover changes and the spatial interactions between each pixel and its neighboring pixels using a local spatial autocorrelation measure. The core hotspots of land cover changes can be delineated by a contiguity-dominance model of our AMOEBA-CH method. We tested our algorithm in a simulation for land cover changes using NDVI (Normalized Difference Vegetation Index) data in South Korea between 2000 and 2008.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.4
• /
• pp.1479-1487
• /
• 2013

The river levee collapse and flood damages are dramatically increased due to the floods which caused by abnormal weather nowadays. The counterplan like TDR(Time Domain Reflectometry) river levee leaking exploration technique is needed to that levee failure causes of levee failure such as levee failure by penetration, piping, inadequate levee materials selection, poor compaction are almost 52% of the failure. This research practiced various comparing experiments of existing TDR(probe and tube types) and developing CAP type TDR to evaluate acrylic small CAP mould and low-cost TDR levee leaking monitoring system which was used probe type TDR. As the result, evaluated TDR system had 20cm critical exploration performance which was a leaking exploration performance, The functional ratio of TDR exploration sensitivity of dry density was sensitive more than 3 times than dry density, and weathered granite soil foundation water contents(w)-dielectric constant(${\epsilon}$) corelation formula was suggested to measure functional ratio on developing cap type TDR system.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05b
• /
• pp.37-40
• /
• 1998

Fe량을 0 - 0.4 wt.%까지 변화시켜 Zr-Fe 이원계 합금을 진공아크용해로 제조한 후 1050 $^{\circ}C$에서 30분 균질화 처리 및 700 $^{\circ}C$에서의 열간압연, 그리고 2회의 걸친 냉간압연 및 열처리를 통하여 판재로 제조되었다. 중간 열처리 시 열처리 온도 및 시간을 조절하여 최종 냉간가공에 앞서 각 시편의 결정립 크기 및 경도 값이 같도록 조절하였다. 최종 냉간가공 시 냉간가공량을 60%로 동일하게 조절하였고, 최종열처리 시 열처리 온도 및 시간을 300-750 $^{\circ}C$, 5-3000분으로 각각 변화시켰다. 재결정 정도는 미세조직 관찰 및 경도 측정으로 평가되었으며, 석출물의 구조, 분포 및 형상 등도 TEM으로 분석되었다. 0.1 wt.% 정도까지의 Fe 첨가는 Fe를 첨가하지 않은 순수지르코늄에 비하여 지르코늄입자의 빠른 성장을 야기해, 조대한 재결정 지르코늄 입자들이 나타났다. 그러나 Fe 첨가량이 0.1wt.%이상 첨가되면, Zr$_3$Fe 석출물에 의한 입자성장 억제효과로 지르코늄 입자의 크기는 오히려 작아졌다. 결론적으로, Fe의 첨가는 지르코늄의 확산을 가속시켰다는 것을 보여준다. 한편, 750 $^{\circ}C$에서 열처리 시 이차 재결정현상으로 지르코늄 입자가 비정상적으로 매우 커졌으며, 동시에 annealing twining 현상이 관찰되었다. 이러한 annealing twining 현상은, 입자성장속도가 임계치 이상으로 갑자기 커진, Zr$_3$Fe 석출물이 거의 없는 합금에서만 나타났다. 이 결과를 토대로 annealing twining 현상은 입자의 빠른 이동이 필요 조건이라는 결론을 도출하였다. .Ar-4vol.%H$_2$ 분위기보다 H$_2$분위기에서 소결했을 때 밀도가 더 높았다. 그러나, 결정립은 $UO_2$와 $UO_2$-Li$_2$O의 경우, 수소분위기에서 소결했을 때, (U,Ce)O$_2$와 (U,Ce)O$_2$-Li$_2$O에서는 Ar-4vol.%H$_2$분위기에서 소결했을 때 더욱 성장하였다.설명해 줄 수 있다. 넷째, 불규칙적이며 종잡기 힘들고 단편적인 것으로만 보이던 중간언어도 일정한 체계 속에서 변화한다는 사실을 알 수 있다. 다섯째, 종전의 오류 분석에서는 지나치게 모국어의 영향만 강조하고 다른 요인들에 대해서는 다분히 추상적인 언급으로 끝났지만 이 분석을 통 해서 배경어, 목표어, 특히 중간규칙의 역할이 괄목할 만한 것임을 가시적으로 관찰할 수 있 다. 이와 같은 오류분석 방법은 학습자의 모국어 및 관련 외국어의 음운규칙만 알면 어느 학습대상 외국어에라도 적용할 수 있는 보편성을 지니는 것으로 사료된다.없다. 그렇다면 겹의문사를 [-wh]의리를 지 닌 의문사의 병렬로 분석할 수 없다. 예를 들어 누구누구를 [주구-이-ν가] [누구누구-이- ν가]로부터 생성되었다고 볼 수 없다. 그러므로 [-wh] 겹의문사는 복수 의미를 지닐 수 없 다. 그러면 단수 의미는 어떻게 생성되는가\ulcorner 본 논문에서는 표면적 형태에도 불구하고 [-wh]의미의 겹의문사는 병렬적 관계의 합성어가 아니라 내부구조를 지니지 않은 단순한 단어(minimal $X^{0}$ elements)로 가정한다. 즉, [+wh] 의미의 겹의문사는 동일한 구성요 소를 지닌 병렬적 합성어

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.1
• /
• pp.44-51
• /
• 2000

We have analyzed optical matched filters considering the third order signals in the optical code division multiple access (CDMA) system based on optical series coupler access encoder (SCAE) and series coupler access decoder (SCAD). In previous studies, the performance evaluation of the optical CDMA system using SCAE and SCAD was not sufficiently accurate because they analyzed system performance only considering the first order signals. Since optical SCAE and SCAD intrinsically have high order signals of various patterns as the number of coupler increases, they change auto- and cross-correlation intensities. Thus, it is necessary to investigate properties of the third order signals so that we may analyze the exact performance of system. In this paper, we mathematically interpret the optical signals up to the third order, and analyzed the effects of th third order signals on auto- and cross-correlation intensities. In result, as ${\alpha}$(coupling coefficient) value increases, the intensity of the third order signals increases. It is found that the peak to side-lobe ratio considering the third order signals is degraded by 3.75 dB at N(coupler number)=5 and ${\alpha}$=0.5. Also if threshold value in receiver is set by main-lobe peak of the first order signals, it is found that the number of users in an optical CDMA system is limited because the intensity peak of side-lobes is raised by the third order signals.