• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1991.04a
• /
• pp.83-89
• /
• 1991

본 연구에서는 5축 능동형 자기베어링 시스템에 대한 설계 및 제작 방법을 소개하고 모우드 변수 및 임계속도, 과도 및 정상상태에서의 응답 특성 등 관련 동특성을 실험으로 규명하였다. 자기베어링 제어방식은 PID 제어를 이 용하였고, air jet를 이용하여 회전체를 구동할 수 있도록 실험장치를 구성하 였다. 실험을 통하여 안정한 부상특성을 실현하였고, 1,2차의 임계속도를 통 과하여 10,000rpm이상이 회전속도에서도 안정하게 운전할 수 있었다.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.4
• /
• pp.19-24
• /
• 2001

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.6
• /
• pp.92-99
• /
• 2005

Numerical analyses of critical speed and mass unbalance response are performed for a 30 ton thrust turbopump. The stiffness and damping of ball bearings and non-contact seals are quantified under aerodynamic and hydrodynamic loads induced by a fuel pump and turbine. Critical speed margin and tip displacements of the rotating parts are evaluated using a three-dimensional finite element method. The results are used to ensure the soundness of the rotordynamic design using an one-dimensional transfer matrix method. A further study shows that sufficient resonance margin may be assured via controlling the stiffness of the rotor support by employing an additional elastic ring to the bearing support.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.1
• /
• pp.56-63
• /
• 2003

This paper studies that torque model considered with decaying phase back-EMF is different In conduction and commutation period and analyzes the torque pulsation components mathematically. In this paper, it is proposed a novel method to suppress torque pulsation due to commutation time. First, it propose commutation delay time control method, which is to compensate current slope of rising phase and decaying phase to control commutation time. Current ripple is minimized at non-commutating current and torque ripple is reduced below critical speed range that dc link voltage is the same as four times of back-EMF voltage. However, torque ripple still exists due to the relation with back-EMF and commutating current and it is increased on a large scale above critical speed range, especially. Secondly, proposed method is commutation time control, which is considered with torque pulsation due to the relation of back-EMF and commutating current. Through the proposed method, the torque pulsation can be minimized in the whole speed range as well as range over critical speed.

• Journal of the Korean Society for Railway
• /
• v.13 no.3
• /
• pp.245-250
• /
• 2010

In this work, the stability and safety analysis are carried out to predict the performance of a next generation high-speed railway vehicle (HEMU-400X). Since the safety of the high-speed railway vehicles is very important, it is meaningful to predict the dynamic performance and stability of the railway vehicles using a numerical model at a railway vehicle design step. The critical speed of the dynamic model depending on the conicity of the wheel is calculated in the stability analysis. The critical speed calculated in this analysis is over 400km/h for the conicity value of 0.15, which is determined on the basis of representative international standard, UIC 518. Also, the lateral and vertical accelerations at several points of the same dynamic model are calculated for the safety analysis. In the simulation, the dynamic model runs at the test speed of 440km/h, which is determined considering a maximum target speed, and the total driving distance is 30km. And those estimated values are less than the allowed maximum acceleration values of UIC 518.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05c
• /
• pp.188-192
• /
• 1996

재결정 Zircaloy-2의 요드에 의한 응력부식균열의 전파속도를 직류전압강하측정법 (DCPD, Direct Current Potential Drop)을 이용하여 측정하고 임계응력집중계수( $K_{ISCC}$)를 구하였다. 임계요드농도 이상인 0.01 MPa의 요드농도에서, $K_{ISCC}$는 300 $^{\circ}C$의 경우 약 15 MPa√m, 350 $^{\circ}C$의 경우 약 12 MPa√m의 응력계수였으며, plateau 구역에서의 균열속도는 $10^{-4}$~ $10^{-3}$ mm/sec 영역이었다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.4
• /
• pp.86-92
• /
• 2017

In this study, a running performance evaluation and roller rig test was conducted to evaluate the applicability of a composite bogie frame, which has the role of the primary suspension. The composite bogie frame was made of a GEP224 glass/epoxy prepreg. Vehicle dynamic analysis was carried out on the composite bogie with three different kinds of side beam thicknesses (50 mm, 80 mm, and 150 mm). From the results, the composite bogie with a side beam thickness of 80 mm satisfied all the dynamic design requirements. Although the composite bogie with the side beam thickness of 50mm also met the design requirements, its critical speed was just a 2% margin to the requirement. In contrast, the model of the side beam thickness of 150mm did not meet the ride comfort. In addition, a composite bogie frame with the side beam thickness of 80 mm was fabricated and installed on a complete bogie. Moreover, the roller rig test using the fully equipped bogie was performed to evaluate the critical speed. During the test, the lateral excitation was imposed on the wheelsets to realize the rail irregularity. There was no divergence of the lateral displacement of the wheelsets while increasing the speed. The measured critical speed was similar to the predicted result.

• Journal of Korea Foundry Society
• /
• v.23 no.3
• /
• pp.147-152
• /
• 2003

질소 용해도가 낮은 ${\delta}$상으로 응고가 시작되는 16Cr-3Ni 계 스테인리스강의 응고시 질소기포 형성에 미치는 질소 함량과 냉각속도의 영향이 조사되었으며 이를 기반으로 질소 기포 결함이 발생하는 임계 질소 함량을 예측하는 방법을 제시하였다. 질소함량의 증가는 질소 기포 결함을 증가시켰으며, 냉각속도의 증가는 질소기포결함의 형성을 다소 억제 할 수 있는 것으로 조사되었다. 실험적으로 구한 Fe-16Cr-3Ni-9Mn 합금의 임계 질소 함량은 0.19wt%였으며, 임계 질소 압력은 평형응고로 가정한 경우 1.27atm, Scheil 응고로 가정한 경우에는 1.23atm으로 계산되었다. 질소 용해도를 증가시킬 수 있는 Mn 함량의 변화에 따른 임계 질소 함량의 변화를 예측하기 위하여 계산된 임계 질소 압력을 Fe-16Cr-3Ni-11Mn 합금에 적용하였으며 이를 통해 얻은 임계 질소 함량은 평형응고로 가정한 경우 0.25wt%, Scheil 응고로 가정한 경우에는 0.24wt% 로 예측되었다. 예측 결과의 타당성을 확인하기 위하여 Fe-16Cr-3Ni-11Mn 합금의 실험 결과와 비교하였으며, 일치하는 결과가 얻어졌다.

• Journal of the Korean Society for Precision Engineering
• /
• v.34 no.3
• /
• pp.205-210
• /
• 2017

Critical speed analysis was conducted for a active steering bogie prototype, developed to improve the curving performance of railway vehicles. The critical speed for the design concept was about 169.2k m/h. To validate the analysis result, we performed a critical speed test for the prototype bogie using a roller-rig tester. The test results showed that the critical speed for the prototype bogie was about 165 km/h. From the analysis and test results, The critical speed for the prototype bogie was determined to be 165 km/h. Considering the maximum operating speed of the test vehicle is 100 km/h, the prototype bogie is considered stable.

• Journal of KSNVE
• /
• v.11 no.2
• /
• pp.265-275
• /
• 2001

This research has been performed to reveal the hysteresis phenomena of the hunting motion in a railway passenger cars. It is found that there are some factors and its operation region to make the nonlinear critical speed reacts to them more sensitively than the linear critical speed. The simulation results show that a self steering bogie system can be a substitute proposal to improve curving Performance together with the reduction of hysteresis of critical speed. Full scale roller rig test is carried out for the validation of the numerical results. Finally, it is certified that wear of wheel profile and stiffness discontinuities of wheelset suspension caused by deterioration have to be considered in the analysis to predict the hysteresis of critical speed precisely.