• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.11
• /
• pp.66-76
• /
• 2009

The motion estimation in video encoding system occupies the biggest part. So, we require the motion estimator with efficient structure for real-time operation. And for motion estimator's implementation, it is desired to design hardware module of an exclusive use that perform the encoding process at high speed. This paper proposes motion estimation detection block(MED), 41 SADs(Sum of Absolute Difference) calculation block, minimum SAD calculation and motion vector generation block based on parallel processing. The parallel processing can reduce effectively the amount of the operation. The minimum SAD calculation and MED block uses the pre-computation technique for reducing switching activity of the input signal. It results in high-speed operation. The MED and 41 SADs calculation blocks are composed of adder tree which causes the problem of critical path. So, the structure of adder tree has changed the most commonly used ripple carry adder(RCA) with carry skip adder(CSA). It enables adder tree to operate at high speed. In addition, as we enabled to easily control key variables such as control signal of search range from the outside, the efficiency of hardware structure increased. Simulation and FPGA verification results show that the delay of MED block generating the critical path at the motion estimator is reduced about 19.89% than the conventional strukcture.

• Applied Biological Chemistry
• /
• v.17 no.1
• /
• pp.42-48
• /
• 1974

Hot air thin layer drying method was studied for red pepper, Capsicum annum var. longum as the whole and cut pod states, at various temperature and air velocities. Drying curve of whole pod showed a settling down period followed by the first and second falling rate periods. By lowering the drying temperature, the first falling rate period approached to a constant rate one. Cut drying curve had simple falling rate period and also cut drying method could effectively shorten the drying time. Drying rate constant, k, was varied with time for both the drying methods and the plots of k vs. time in two methods sugested the different drying mechanisms. When an average k was taken as a constant value, the following equations; $M-M_e/M_o-M_e=e^{-0.118t}$ and $M-M_e/M_o-M_e=e(-0.342t^{0.128})$ were applicable for whole and cut drying, respectively.

• Journal of the Mineralogical Society of Korea
• /
• v.15 no.3
• /
• pp.195-204
• /
• 2002

Mineralogy and the exposed surface area are two of the most important factors controlling dissolution and weathering rates of soils. The mixture of inorganic and organic materials of various size distributions and structures that constitute soils makes the calculation of weathering rates difficult. The surface area of soil minerals plays an important role in most of programs for calculating the weathering rates and critical loads. The Brunauer-Emmett-Teller (BET) measurement is recommended for the measurement of specific surface area. However, BET values measured without organic matter removal are in fact those far all the N2-adsorbed surface areas, including the surfaces covered and aggregated with organisms. Surfaces occupied by organisms are assumed to be more reactive to weathering by organic activities. Therefore, the BET surface area difference before and after organic removal depicts the area occupied by organisms. The present study shows that the BET values after organic matter removal using $H_2$O$_2$ are larger than those without removal by 1.68~4.87 $m^2$/g. This implies that BET measurement without organic removal excludes the reactive area occupied by organisms and that the area occupied by organisms in soils is much larger than expected. It is suggested that specific surface area measurement for calculating weathering rates of mineral soils should be made before and after organic matter removal. The results of a column experiment are presented to demonstrate the potential retarding influence that this organic matter may have on mineral dissolution and weathering.

• Journal of the Korea Concrete Institute
• /
• v.21 no.1
• /
• pp.13-20
• /
• 2009

The influence of steel fiber volume on the tension softening behavior in steel fiber-reinforced ultra high strength concrete was investigated. Three-point bending test (TPBT) with notched beams was performed and inverse analysis method by Uchida et al. was adopted to obtain the tension softening behaviors from the results of TPBT. It could be found that the intial stiffness was constant regardless of steel fiber volume, the increase of steel fiber volume fraction made the tensile strength higher, but all of the curves converged on an asymptote with a crack width. It was proposed the equation of softening curve expressed by combination of plastic behavior part and exponential descending behavior part considering the steel fiber volume fraction and $\omega_0$, which is corresponding to the maximum crack width of plastic area. Thereafter, the crack propagation analysis using finite element method with smeared crack model was also carried out and it was confirmed that the proposed equation had a good agreement with the experimental results.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2004.05b
• /
• pp.731-736
• /
• 2004

강우-유출과정의 수문학적 현상을 보다 정확히 분석하고 예측하는 기법으로 강우에 의한 유출의 반응을 나타내는 지체시간, 도달시간 등 수문학적 반응시간을 유역의 지형형태학적 인자들과 연계하는 방법이 많이 이용되고 있다. 이에 본 연구에서는 Clark방법과 지형형태학적 순간단위도(GIUH)를 이용하여 계측유역의 강우-유출반응을 모의하였고, 이를 관측된 값과 비교하여 미계측유역의 적용성 여부를 검토해보았다. 대상 유역의 하상지형인자 및 지형형태학적 특성은 Arc-View를 이용하여 구하였으며, 이를 기존의 문헌자료와 비교해보았다. Clark방법의 매개변수의 결정에 있어서 시간-면적곡선은 HEC-1의 무차원 식을 이용하였고, 도달시간은 Kirpich 공식을 이용하여 구하였으며, 저류상수는 Clark방법에 의해 추정된 순간단위도의 첨두유량이 Horton의 차수비의 함수로 구한 철두유량과 같아지는 값으로 결정하였다. 본 연구는 전적비교를 출구점으로하는 유역면적 $8.5km^2$인 설마천을 대상유역으로 하였으며, 모의된 강우-유출반응과 비교하기 위해 사용된 강우사상은 2002년의 8월 4일과 2002년 10월 6일의 10분 단위 우량이다. Clark방법과 GIUH를 이용하여 모의한 유출곡선과 관측된 유출곡선을 비교해본 결과 첨두유량은 8월의 강우사상 때는 $21\%$크게, 10월의 강우사상 때는 $35\%$작게 나타났다. 첨두시간은 모의된 경우가 각각 10분, 20분 빨리 도달하였다. 또한 이러한 결과는 유역의 도달시긴에 가장 민감하게 반응함을 알 수 있었다. 따라서, 유역의 도달시간 산정에 주의를 요한다면 프랙탈 차원이 유사한 미계측유역의 수문곡선 산정에 있어서 Clark방법과 GIUH를 이용하는 방법도 유용하다고 사료된다. 주는 각 수문인자 중 강우시간분포와 유효우량 산정방법 그리고 유출모형에 대해 자자 검토하였으며, 최종적으로 면적에 따른 임계지속기간과 유출량의 변화를 검토해 보았다.이를 각각의 경우의 해석해 결과와 비교${\cdot}$분석하였다. 후방추적 퍼프모형은 전방추적 퍼프모형에 비하여 사용된 퍼프수와 관계없이 작은 오차를 발생하였으며, 전체적으로 퍼프 모형이 입자모형보다는 훨씬 적은 수의 계산을 통해서도 작은 오차를 나타낼 수 있다는 것을 알 수 있었다. 그러나 Gaussian 분포를 갖는 퍼프모형은 전단흐름에서의 긴 유선형 농도분포를 모의할 수 없었고, 이에 관한 오차는 전단계수가 증가함에 따라 비선형적으로 증가하였다. 향후, 보다 다양한 흐름영역에서 장${\cdot}$단점 분석 및 오차해석을 수행한 후에 각각의 Lagrangian 모형의 장점만을 갖는 모형결합 방법을 제시할 수 있을 것으로 판단된다.mm/$m^{2}$로 감소한 소견을 보였다. 승모판 성형술은 전 승모판엽 탈출증이 있는 두 환아에서 동시에 시행하였다. 수술 후 1년 내 시행한 심초음파에서 모든 환아에서 단지 경등도 이하의 승모판 폐쇄 부전 소견을 보였다. 수술 후 조기 사망은 없었으며, 합병증으로는 유미흉이 한 명에서 있었다. 술 후 10개월째 허혈성 확장성 심근증이 호전되지 않아 Dor 술식을 시행한 후 사망한 예를 제외한 나머지 6명은 특이 증상 없이 정상 생활 중이다 결론: 좌관상동맥 페동맥이상 기시증은 드물기는 하나, 영유아기에 심근경색 및 허혈성 심근증 또는 선천성 승모판 폐쇄 부전등을 초래하는 심각한 선천성 심질환이다. 그러나 진단 즉시 직접 좌관상동맥-대동맥 이식술로 수술적 교정을 해줌으로써 좋은 성적을 기대할 수 있음을 보여주었다.특히 교사들이 중요하

• Journal of Korea Water Resources Association
• /
• v.53 no.6
• /
• pp.427-436
• /
• 2020

It is uncertain how global climate change will influence future drought characteristics over the Korean peninsula. This study aims to project the future droughts using climate change and land use change scenarios over the Korean peninsula with the land surface modeling system, i.e., Weather Research and Forecasting Model Hydrological modeling system (WRF-Hydro). The Representative Concentration Pathways (RCPs) 2.6 and 8.5 are used as future climate scenarios and the Shared Socio-economic Pathways (SSPs), specifically SSP2, is adopted for the land use scenario. The using Threshold Level Method (TLM), we identify future hydrological and ecological drought events with runoff and Net Primary Productivity (NPP), respectively, and assess drought characteristics of durations and intensities in different scenarios. Results show that the duration of drought is longer over RCP2.6-SSP2 for near future (2031-2050) and RCP8.5-SSP2 (2080-2099) for the far future for hydrological drought. On the other hand, RCP2.6-SSP2 for the far future and RCP8.5-SSP2 for the near future show longer duration for ecological drought. In addition, the drought intensities in both hydrological and ecological drought show different characteristics with the drought duration. The intensity of the hydrological droughts was greatly affected by threshold level methods and RCP2.6-SSP2 for far future shows the severest intensity. However, for ecological drought, the difference of the intensity among the threshold level is not significant and RCP2.6-SSP2 for near future and RCP2.6-SSP2 for near future show the severest intensity. This study suggests a possible future drought characteristics is in the Korea peninsula using combined climate and land use changes, which will help the community to understand and manage the future drought risks.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.16 no.4
• /
• pp.223-237
• /
• 2011

The intermittent freshwater discharge has an critical influence upon the biophysical environments and the ecosystems of the Yeongsan Estuary where the estuary dam altered the continuous mixing of saltwater and freshwater. Though freshwater discharge is controlled by human, the extreme events are mainly driven by the heavy rainfall in the river basin, and provide various impacts, depending on its magnitude and frequency. This research aims to evaluate the magnitude and frequency of extreme freshwater discharges, and to establish the magnitude-frequency relationships between basin-wide rainfall and freshwater inflow. Daily discharge and daily basin-averaged rainfall from Jan 1, 1997 to Aug 31, 2010 were used to determine the relations between discharge and rainfall. Consecutive daily discharges were grouped into independent events using well-defined event-separation algorithm. Partial duration series were extracted to obtain the proper probability distribution function for extreme discharges and corresponding rainfall events. Extreme discharge events over the threshold 133,656,000 $m^3$ count up to 46 for 13.7y years, following the Weibull distribution with k=1.4. The 3-day accumulated rain-falls which occurred one day before peak discharges (1day-before-3day -sum rainfall), are determined as a control variable for discharge, because their magnitude is best correlated with that of the extreme discharge events. The minimum value of the corresponding 1day-before-3day-sum rainfall, 50.98mm is initially set to a threshold for the selection of discharge-inducing rainfall cases. The number of 1day-before-3day-sum rainfall groups after selection, however, exceeds that of the extreme discharge events. The canonical discriminant analysis indicates that water level over target level (-1.35 m EL.) can be useful to divide the 1day-before-3day-sum rainfall groups into discharge-induced and non-discharge ones. It also shows that the newly-set threshold, 104mm, can just separate these two cases without errors. The magnitude-frequency relationships between rainfall and discharge are established with the newly-selected lday-before-3day-sum rainfalls: $D=1.111{\times}10^8+1.677{\times}10^6{\overline{r_{3day}}$, (${\overline{r_{3day}}{\geqq}104$, $R^2=0.459$), $T_d=1.326T^{0.683}_{r3}$, $T_d=0.117{\exp}[0.0155{\overline{r_{3day}}]$, where D is the quantity of discharge, ${\overline{r_{3day}}$ the 1day-before-3day-sum rainfall, $T_{r3}$ and $T_d$, are respectively return periods of 1day-before-3day-sum rainfall and freshwater discharge. These relations provide the framework to evaluate the effect of freshwater discharge on estuarine flow structure, water quality, responses of ecosystems from the perspective of magnitude and frequency.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.6
• /
• pp.453-457
• /
• 2016

In various industrial plants such as power generation plants, petrochemical plants, and unit factories, there is an increasing demand for a system that generates hot water using waste or surplus steam. Compact steam unit (CSU), which produces hot water by using steam, is a good solution considering energy reuse. In this study, as a basic study to develop a high-pressure CSU, heat transfer characteristics of a hybrid heat exchanger were investigated through experiments, in order to use the hybrid heat exchanger instead of a conventional plate heat exchanger as the core component of CSU. The experimental results are the followings. Heat balance between the hot side and cold side was satisfied within ${\pm}5%$. Overall heat transfer coefficient increased linearly as the Reynolds number increased and exceeded $5,524W/m^2K$ when the flow velocity was above 0.5 m/s. In addition, pressure drop also increased as the Reynolds number increased, and pressure drop per unit length was below 50 kPa/m.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.11A
• /
• pp.1027-1034
• /
• 2005

IEEE802.15.4a, which is started to realize the PHY layer including high precision ranging/positioning and low data rate communication functions, requires a simple and low power consumable transceiver architecture. To satisfy this requirements, the simple noncoherent on-off keying (OOK) UWB transceiver with the parallel energy window banks (PEWB) giving high precision signal processing interface is proposed. The flexibility of the proposed system in multipath fading channel environments is acquired with the pulse and bit repetition method. To analyze the bit error rate (BER) performance of this proposed system, a noise model in receiver is derived with commonly used random variable distribution, chi-square. BER of $10^{-5}$ under the line-of-sight (LOS) residential channel is achieved with the integration time of 32 ns and signal to noise ratio (SNR) of 15.3 dB. For the non-line-of-sight (NLOS) outdoor channel, the integration time of 72 ns and SNR of 16.2 dB are needed. The integrated energy to total received energy (IRR) for the best BER performance is about $86\%$.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.5C
• /
• pp.413-421
• /
• 2008

The paper derives asymptotic formulas for the MSE distortion and the signal-to-noise ratio of a mismatched fixed-rate minimum MSE Laplacian quantizer. These closed-form formulas are expressed in terms of the number N of quantization points, the mean displacement $\mu$, and the ratio $\rho$ of the standard deviation of the source to that for which the quantizer is optimally designed. Numerical results show that the principal formula is accurate in that, for rate R=$log_2N{\geq}6$, it predicts signal-to-noise ratios within 1% of the true values for a wide range of $\mu$, and $\rho$. The new findings herein include the fact that, for heavy variance mismatch of ${\rho}>3/2$, the signal-to-noise ratio increases at the rate of $9/\rho$ dB/bit, which is slower than the usual 6 dB/bit, and the fact that an optimal uniform quantizer, though optimally designed, is slightly more than critically mismatched to the source. It is also found that signal-to-noise ratio loss due to $\mu$ is moderate. The derived formulas can be useful in quantization of speech or music signals, which are modeled well as Laplacian sources and have changing short-term variances.