• Journal of the Korean Magnetics Society
• /
• v.16 no.1
• /
• pp.6-10
• /
• 2006

The sulphur spinel $FeCr_{2-x}M_xS_4$(M=Ga, In) have been studied with Mossbauer spectroscopy, x-ray diffraction (XRD), and vibrating sample magnetometer. The XRB patterns for samples $FeCr_{2-x}M_xS_4$(M=Ga, In: x=0.1, 0.3) reveal a single phase, which the Ga and In ions are partially occupied to the tetrahedral (A) site. The Neel temperature for the Ga substituted samples increases from 180 to 188 K, with increase from x=0.1 to 0.3. While, it decreases from 173 to 160 K, for the In substituted samples of the x=0.1 and 0.3, respectively. The Mossbauer spectra were collected from 4.2 K to room temperature. We have analyzed the Mossbauer spectra using eight Lorentzian lines fitting method for the $FeCr_{2-x}In_xS_4$(x=0.1) at 4.2 K, yielding the 1311owing results; $H_{hf}=146.0kOe,\;{\Delta}E_Q=1.88mm/s,\;\theta=36^{\circ},\;\phi=0^{\circ},\;\eta=0.6$, and R=1.9. The Ga ions enter into the both sites octahedral (B) and tetrahedral (A), simultaneously the same amounts of Fe ions migrate from the A to the B site, this result is an agreement with XRD results, too. The ${\Delta}E_Q$ of the A and B site in Mossbauer spectra of the samples $FeCr_{2-x}Ga_xS_4$(x=0.3) are 0.83 and 2.94mm/s, respectively. While they are 0.56 and 2.36mm/s for the $FeCr_{2-x}In_xS_4$(x=0.3). It is noticeable that the ${\Delta}E_Q$ for the Ga doped samples are larger than that of the corresponding In doped samples, in spite of the larger ionic radius for In ions. The bond lengths of Cr-S, for the Ga and In doped samples (x=0.3) are found to be 2.41 and $2.43\;{\AA}$, respectively. We interpret that the larger covalence effect from the smaller bond length induces a large asymmetric charge distribution. Finally, it gives a large quadrupole interaction.

• Journal of the Korean Magnetics Society
• /
• v.13 no.6
• /
• pp.237-242
• /
• 2003

$Ti_{1-x}$$^{57}$ F $e_{x}$ $O_2$(0.0$\leq$x$\leq$0.07) compounds were fabricated using the sol-gel method, and the crystal structure and magnetic properties were investigated as a function of doped $^{57}$ Fe concentration. X-ray diffraction patterns showed a pure anatase single phase, without any segregation of Fe into particulate. With varying $^{57}$ Fe concentration, we could observe unusual magnetic phenomena in these materials. Doping $^{57}$ Fe into the Ti $O_2$ nonmagnetic semiconductor formed magnetic properties, but the gradual increase of $^{57}$ Fe concentration decreased rapidly the ferromagnetic properties rather than enhanced the ferromagnetic properties. Obvious ferromagnetic behavior was shown for the samples with x$\leq$0.01, while paramagnetic behavior was shown for the sample with x$\geq$0.03. These phenomena could be verified using Mossbauer measurement. Separation of the ferromagnetic phase (sextet) and the paramagnetic phase (doublet) of the samples with different $^{57}$ Fe concentration was characterized. Samples with x$\leq$0.01 have sextet and doublet simultaneously, but samples with x$\geq$0.03 have only doublet at room temperature. This indicates that the sample x$\leq$0.01 have the ferromagnetic phase at room temperature. This result corresponded with the M-H loops referenced above and reveals an interesting feature that there is a critical limit of $^{57}$ Fe concentration (0.01$\leq$0.01 samples was fundamentally attributable to the paramagnetic phase as well as the ferromagnetic phase.e.

• Journal of Oral Medicine and Pain
• /
• v.31 no.4
• /
• pp.355-364
• /
• 2006

Headache is a common disease which influences not only individually but also socially. Temporomandibular disorders(TMD) refers to pain and dysfunction within the temporomandibular joint(TMJ) and associated muscles. TMD is presented commonly, and 70% of population are found to have one or more related symptom. A number of studies have been conducted to verify the association between headache and TMD, and some authors have proposed that headache and TMD may be related. In this study, we studied the patterns of headache presented by the patients who visited the TMJ and Orofacial pain clinic. Among the patients participated in this study, tension type headache showed the highest prevalence(48.5%), followed by migraine without aura(15.0%), probable migraine(10.6%), migraine with aura(7.1%), probable tension type headache(4.8%), and other primary headaches(1.8%). The high prevalence of tension type headache may be due to the accompaniment of orofacial pain by pericranial muscle tenderness. Comparison of sex showed that the rate of migraine was higher in female than male(female to male ratio 35.8:25.3). In age analysis, the rate of migraine was high in the twenties(42.2%) and the thirties(40.0%). As the age increased, the rate of migraine decreased, and this trend was in accordance with the previous studies. The percentage of the patients who had previously received treatment was only 26.2%, and that of those who were aware of the diagnosis was merely 8.7%. Therefore, it is not common for headache patients to get treatment, however, since orofacial pain is often accompanied by headache, more systematic diagnosis as well as precise treatment would be necessary. Moreover, since TMD could induce and aggravate headache, proper evaluation and management of TMD would be essential for diagnosis and treatment of headache. In the future, more systematic and broad investigation on the influence of causative factors of TMD on headache as well as the change in headache pattern with the treatment of TMD would be required.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.46 no.5
• /
• pp.646-652
• /
• 2017

The aim of this study was to investigate method validation for determination of sesamol, sesamin, and sesamolin in non-fermented sesame and fermented sesame by bioconversion. For validation, the specificity, linearity, precision, accuracy, limits of detection (LOD), and quantification (LOQ) of sesamol, sesamin, and sesamolin were measured by HPLC. Linearity tests showed that the coefficients of calibration correlation ($R^2$) for sesamol, sesamin, and sesamolin were 0.9999. Recovery rates of lignan contents in non-fermented and fermented sesame were high in the ranges of 100.27~115.10% and 98.43~114.90%, respectively. The inter-day and intra-day precisions of sesamin and sesamolin analyses for non-fermented and fermented sesame were 0.27~1.94% and 0.25~0.69%, respectively. The LOD and LOQ were $0.23{\sim}0.34{\mu}g/g$ and $0.70{\sim}1.03{\mu}g/g$, respectively. These results indicate that the validated method is appropriate for the determination of sesamol, sesamin, and sesamolin.

• Journal of the Korean Magnetics Society
• /
• v.5 no.4
• /
• pp.269-274
• /
• 1995

The basic composition of Mn-Zn ferrite was $Mn_{0.631}Zn_{0.316}Fe_{2.053}O_{4}$(specimen A), $Mn_{0.584}Zn_{0.312}Fe_{2.104}O_{4}$(specimen B) and $Mn_{0.538}Zn_{0.308}Fe_{2.154}O_{4}$(specimen C) with additional 0.1 mol % $CaCo_{3}$ and 0.04 mol % $V_{2}O_{5}$. For high per¬meability and acceleration of grain growth, $CaCo_{3}$ and $V_{2}O_{5}$. was added. The mixture of the law materials was calcinated at $950^{\circ}C$ for 3 hours and then milled. The compacts of toroidal type were sintered at different temperature($1250^{\circ}C$, $1300^{\circ}C$, $1350^{\circ}C$) for 2 hours in $N_2$ atmosphere. The effects of the various raw material composition and sintered temperature on the physical properties of Mn-Zn ferrite have been investigated. They turned out to be spinel structure by X-ray diffraction and the size of grain from SEM was from $18\;\mu\textrm{m}\;to\;23\;\mu\textrm{m}$. As the sintering temperature was increased from $1250^{\circ}C$ to $1350^{\circ}C$, the initial permeability and magnetic induction has increased and the both of Q factor and coercive force has decreased. The coercive force and curie temperature were almost the same at each specimen Their values were about 0.45 Oe and $200^{\circ}C$. The frequency of specimen will used in the range from 200 kHz to 2 MHz. The basic composition of $Mn_{0.584}Zn_{0.312}Fe_{2.104}O_{4}$(specimen B) sintered at $1300^{\circ}C$ shows the best results at magnetic induction (Br & Bm).

• Journal of Korea Water Resources Association
• /
• v.51 no.9
• /
• pp.827-837
• /
• 2018

The stabilities of sliding and overturning of caisson and bearing capacity of mound against eccentric and inclined loads, which possibly happen to a composite caisson breakwaters, have been analyzed by using the technique of multiple failure modes. In deterministic approach, mathematical functions have been first derived from the ultimate limit state equations. Using those functions, the minimum cross section of caisson can straightforwardly be evaluated. By taking a look into some various deterministic analyses, it has been found that the conflict between failure modes can be occurred, such that the stability of bearing capacity of mound decreased as the stability of sliding increased. Therefore, the multiple failure modes for the composite caisson breakwaters should be taken into account simultaneously even in the process of deterministically evaluating the design cross section of caisson. Meanwhile, the reliability analyses on multiple failure modes have been implemented to the cross section determined by the sliding failure mode. It has been shown that the system failure probabilities of the composite breakwater are very behaved differently according to the variation of incident waves. The failure probabilities of system tend also to increase as the crest freeboards of caisson are heightening. The similar behaviors are taken place in cases that the water depths above mound are deepening. Finally, the results of the first-order modal are quite coincided with those of the second-order modal in all conditions of numerical tests performed in this paper. However, the second-order modal have had higher accuracy than the first-order modal. This is mainly due to that some correlations between failure modes can be properly incorporated in the second-order modal. Nevertheless, the first-order modal can also be easily used only when one of failure probabilities among multiple failure modes is extremely larger than others.

• Korean Journal of Food Science and Technology
• /
• v.44 no.6
• /
• pp.686-691
• /
• 2012

The objective of this research is to present method development and validation for the simultaneous determination of lutein and zeaxanthin using ultra performance liquid chromatography (UPLC). Also, rapid quantification was performed on six green leafy vegetables (Allium tuberosum, Aster scaber, Hemerocallis fulva, Pimpinella brachycarpa, Sedum sarmentosum and Spinacia oleracea) that are commonly consumed in Korea. Separation and quantification were successfully achieved with a Waters Acquity BEH C18 ($50{\times}2.1mm$, $1.7{\mu}m$) column by 85% methanol within 5 min. Two compounds showed good linearity ($r^2$ > 0.9968) in $1-150{\mu}g/mL$. Limit of detection (LOD) and quantification (LOQ) for lutein and zeaxanthin were 1.7 and 5.1 g/mL and 2.1 and 6.3 g/mL, respectively. The RSD for intra- and inter-day precision of each compound was less than 10.69%. The recovery of each compound was in the range of 91.75-105.13%. Aster scaber and Spinacia oleracea contained significantly higher amounts of lutein ($4.06{\pm}0.24$ and $3.97{\pm}0.10mg$/100 g of fresh weight), respectively.

• The Journal of Engineering Geology
• /
• v.18 no.4
• /
• pp.555-566
• /
• 2008

Hydrogeochemical study in Samseung area (Boeun, Chungbuk) and waterrock interaction experiment using rock samples from the area were performed to elucidate the fluoride source in groundwater and explaining geochemical behavior of fluoride ion. Fluoride concentration of public water supply mostly using groundwater in Boeun area was significantly higher in South Korea. The maximum fluoride concentration of the study area was 3.9 mg/L, and 23% of samples exceeded the Korean Drinking Water Standard of fluoride (1.5 mg/L). The average concentration of fluoride was 1.0 mg/L and median was 0.5 mg/L. Because of high skewness (1.3), median value is more appropriate to represent fluoride level of this area. The relationships between fluoride ion and geochemical parameters ($Na^+$, $HCO_3$, pH, etc.) indicated that the degree of waterrock interaction was not significant. However, high fluoride samples were observed in $NaHCO_3$ type on Piper's diagram. The negative relationship between fluoride and $NO_3$ ion which might originate from surface contaminants was obvious. These results indicate that fluoride ion in groundwater is geogenic origin. The source of fluoride was proved by waterrock interaction batch test. Fluoride concentration increased up to 1.2 mg/L after 96 hours of reaction between water and biotite granite. However, the relationship between well depth and fluoride ion, and groundwater age and fluoride ion was not clear. This indicates that fluoride ion is not correlated with degree of waterrock interaction in this area but local heterogeneity of fluoriderich minerals in granite terrain. High fluoride concentration in Boeun area seems to be correlated with distribution of permeable structures in hard rocks such as lineaments and faults of this area. This entails that the deep bedrock groundwater discharges through the permeable structures and mixed with shallow groundwater.

• Korean Journal of Soil Science and Fertilizer
• /
• v.31 no.4
• /
• pp.392-399
• /
• 1998

Nitrogen fertilizers such as urea are readily hydrolyzed in soils to produce ammonium ions which pass through nitrification and denitrification processes. These serial processes have drawn attention due to nitrogen losses, eutrophication, blue baby syndrome, and ozone depletion problems. The purpose of this study was to test the inhibitory effects of hot-water extract and organic solvent fractions of Artemisia asiatica leaves on soil urea hydrolysis and nitrification. In addition, the effects of organic solvent fractions on urease activity and ureolytic bacterial population were also investigated. First, hot-water extract of Artemisia asiatica leaves inhibited soil nitrification substantially with a marginal stimulatory effect on soil urea hydrolysis. Soils treated with hot-water extract of Artemisia asiatica leaves showed significant decreases in the accumulation of soil $NO_3-N$ (~68% decrease) compared with the control soil without the treatment of hot-water extract. In contrast, $CHCl_3$/MeOH fraction and basic aqueous layer of Artemisia asiatica leaves inhibited soil urea hydrolysis very strongly, causing 5.8 and 4.3-fold higher accumulation in amounts of remaining urea-N compared with the non-treated soil. Meanwhile, non of the organic solvent fractions showed any significant effects on soil nitrification inhibition. The inhibition of ureolytic bacterial activity by $CHCl_3$/MeOH fraction and aqueous basic layer of Artemisia asiatica leaves without any effects on urease activity itself led us to conclude that the inhibitions of soil urea hydrolysis were caused by the antagonistic effects on ureolytic bacterial activity.

• Radiation Oncology Journal
• /
• v.20 no.3
• /
• pp.264-273
• /
• 2002

Purpose : Three-dimensional radiation dosimetry using magnetic resonance imaging of polymer gel was recently introduced. This dosimetry system is based on radiation induced chain polymerization of acrylic monomers in a muscle equivalent gel and provide accurate 3 dimensional dose distribution. We planned this study to evaluate the clinical value of this 3-dimensional dosimetry. Materials and Methods: The polymer gel poured into a cylindrical glass flask and a spherical glass flask. The cylindrical test tubes were for dose response evaluation and the spherical flasks, which is comparable to the human head, were for isodose curves. T2 maps from MR images were calculated using software, IDL. Dose distributions have been displayed for dosimetry. The same spherical flask of gel and the same irradiation technique was used for film and TLD dosimetry and compared with each other. Results : The R2 of the gel respond linearly with radiation doses in the range of 2 to 15 Gy. The repeated dosimetry of spherical gel showed the same isodose curves. These isodose curves were identical to dose distributions from treatment planning system especially high dose range. In addition, the gel dosimetry system showed comparable or superior results with the film and TLD dosimetry. Conclusion : The 3-dimensional dosimetry for conformal radiation therapy using MRI of polymer gal showed stable and accurate results. Although more studies are needed for convenient clinical application, it appears to be a useful tool for conformal radiation therapy.