• Journal of the korean Society of Automotive Engineers
• /
• v.9 no.6
• /
• pp.37-45
• /
• 1987

최근의 경량화 췌ㅅ로 말미암아 승용차의 차체는 박판일체식 구조로 제작되어 구조적 강성의 약화를 가져 왔으며 이로 인하여 외부의 요인으로부터 발생되는 승용차의 진동문제는 더욱 악화되고 해결하기 어렵게 되어가고 있다. 이 논문에서는 이러한 여러가지 문제로 인하여 전륜구동형 승용차의 조향계에서 발생되는 Shake와 Shimmy를 2-모드 동흡진기를 사용하여 제어하고자 하며 실제적으로 시작품을 제작하여 실차상태에서 확인시험을 실시하였다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.387-388
• /
• 2008

Finding reasonable flexural modes from the full vehicle modal testing has always been a difficult job to N&V engineers due to FRF inconsistency, nonlinearity, heavy damping and, in many cases, interactions between global body structural modes and massive isolate/non-isolated subsystem modes. This paper provides a brier overview of the mode map validation using single-run FRF measurement with highly sensitive accelerometers fur the full vehicle modal analysis and then it can be used to characterize the vehicle's global/local vibration performances, especially customer perceived "structural feel" typically below 40Hz.

• Journal of the Korea Convergence Society
• /
• v.8 no.12
• /
• pp.275-281
• /
• 2017

The automobile cowl cross bar which is a backbone frame part inside the cockpit module has been designed with more complex geometries recently due to demands of its enhanced functions and reduced weight of car. The traditional manufacturing process using welding between tubes with different diameters shows several problems such as poor mechanical characteristics and appearance, etc. Therefore, in this study, manufacturing processes which can eliminate the welding process were developed by applying one-piece metal forming processes such as tube drawing and radial swaging. As results, it was found that the one-piece manufacturing processes give better bending strength than the traditional welding process and the swaging process shows the lowest manufacturing cost.

• Journal of the Korea Convergence Society
• /
• v.3 no.4
• /
• pp.29-34
• /
• 2012

Power window motor assembly including ECU system is important to doors of automobile. This study is done for own development instead of importing of power window motor assembly. This paper is written under five specific subjects. The first, making of prototype sample and analysis of mass-production problem using CAE, the second, design of mass-production mold(2D and 3D), the third, manufacturing of sample mold, the fourth, tryout and measuring of 3 dimensions, the fifth, data analysis and mold modify. In the among them, product sample and analysis of mass-production using CAE, design and manufacture of mass-production mold, and production of sample mold are successfully done. In the results, it is made clear that two cavity and one gate are proper to make a mold of power window motor assembly housing. Besides, it is acquired own technology for mass-production of power window motor.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.3
• /
• pp.562-568
• /
• 2017

A precast floating slab track with a 5m slab panel and installed with isolators is proposed to solve the noise and vibration problem at existing elevated railway stations. Thus, the construction can be carried out rapidly without interrupting the train operation. However, dynamic instability problems may be caused by repeated discontinuities in track due to the short slab panel length and excessive rail displacement due to the inherent operation mechanism of a floating system in reducing the vibration. Furthermore, the difference of the supporting stiffness at the transition between the floating track and ballast track may raise problems. In this study, the assessment factors to evaluate the dynamic stability of the precast floating slab track are presented and assessed with the vehicle-track interaction analysis. Through the analysis, all values relevant to the stability at the floating track section are found to be acceptable, and the slab panels at the transition section are designed to satisfy the stability.