• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.1
• /
• pp.61-65
• /
• 2010

A commercially available soft PZT wafer that is poled in thickness direction is subjected to longitudinal tensile stress loading in both short and open-circuit conditions. Variations of electric displacement in thickness direction and in-plane strains are measured over time during the loading. Different material responses in the two electrical boundary conditions are explained by the effects of piezoelectrically produced internal electric field on linear material moduli and domain switching mechanisms. Finally, a free energy model of normal distribution is introduced to explain the observed creep behavior, and its predictions are compared with experimental observations.

• Journal of the Korea Concrete Institute
• /
• v.15 no.1
• /
• pp.69-77
• /
• 2003

One directional and biaxial tension tests of 13 reinforced concrete panels were conducted to derive a constitutive law of concrete. Based on the test results, a model equation is derived for the stress-strain relationship of concrete in tension. Main test variables are reinforcement ratio and the load ratio applied in two directions. In addition a failure envelope of concrete in tension-tension region is suggested based on the initial crack occurrence. Test results show that the concrete carries substantial tensile stress even after cracking occurrence. However, the application of this proposed stress-strain relationship for concrete is limited to the case where the direction of reinforcement coincides with the direction of the applied principal stresses.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.2
• /
• pp.80-85
• /
• 1999

The purpose of this work is to investigate fatigue damage of quasi-isotropic laminates under tensile loading in different directions. Low cycle fatigue tests of [0/-60/+60]a laminates and [+30/-30/90]s lamina tes were carried out. Material systems used are AS4/Epoxy and AS4/PEEK. The fatigue damage of [+30/-30/90]s is very different from that of [0/-60/+60]s. The position of delamination generated at AS4/Epoxy and AS$/PEEK laminates were differentiated by the matrix difference that is, we suppose, the value of both GIcr(critical energy release rate of mode-I) and GIIIcr(critical energy release rate of mode-III) difference.

• Journal of Korean Society of Steel Construction
• /
• v.19 no.2
• /
• pp.201-210
• /
• 2007

Double-angle connections should be designed with enough stiffness and strength to properly resist various applied loads. Therefore, structural engineers should be able to predict some influential variables and take their effects into account in design. This study was performed to establish the effects of the number of bolts and bolt gage distance on the stiffness and strength of a double-angle connection under tension. Six experimental tests were conducted to describe the effects of these variables by comparing load-displacement relationship curves. In addition, two prediction models were proposed to estimate the initial stiffness and the maximum allowable tensile load based on the results of experimental tests. In the development of these prediction models, the effect of prying action was considered.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.185-186
• /
• 2009

In the present study, the deformation capacity of slender shear walls with thin web was studied. As reported by other researchers, web-crushing and rebar-fracture, developing by inelastic deformation after flexural yielding, were considered as the governing failure modes of walls. To address the effect of the longitudinal elongation on web-crushing and rebar-fracture, the longitudinal elongation was predicted by using truss model analysis. The failure criteria by web-crushing and rebar-fracture were defined as a function of the longitudinal elongation. The proposed method was applied to 17 shear wall specimens with boundary columns, and the prediction results were compared with the test results. The results showed that proposed method predicted the maximum deformations and failure modes of the wall specimens with reasonable precision.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.11
• /
• pp.1207-1214
• /
• 2014

Under excessive plasticity, the fracture toughness of a material depends on its size and geometry. Under fully yielded conditions, the stresses in a material near its crack tip are not unique but rather depend on the geometry. Therefore, the single-parameter J-approach is limited to a high-constraint crack geometry. The JQ theory has been proposed for establishing the crack geometry constraints. This approach assumes that the crack-tip fields have two degrees of freedom. In this study, the crack-tip stress field of a fully circumferential surface-cracked pipe under combined loads is investigated on the basis of the JQ theory by using finite element analysis. The combined loads are a tensile axial force and the thermal gradient in the radial direction. Q-stresses of the crack geometry and its loading state are used to determine the constraint effects. The constraint effects of secondary loading are found to be greater than those of primary loading. Therefore, thermal shock is believed to be the most severe loading condition of constraint effects.

• International Journal of Highway Engineering
• /
• v.11 no.1
• /
• pp.203-215
• /
• 2009

This study was conducted to develop the design methodology of longitudinal post tensioning for the post-tensioned concrete pavement (PTCP). The longitudinal stress distribution in the PTCP slab was analyzed when post tensioning was applied. Then, the tensile stress distribution in the PTCP slab due to the environmental and vehicle loads needed for the design was investigated. In addition, prestress losses were calculated considering the losses due to the frictional resistance between the slab and underlying layer and due to various reasons related to tensioning. The tensile stresses used for the design were obtained by adding the stresses from the critical conditions under both the environmental and vehicle loads. The prestress losses were obtained by considering actual field conditions. The effective post tensioning amount was determined by considering the design loads including environmental and vehicle loads and various losses, and the effect of the allowable tensile stress on the post tensioning amount was investigated. The initial stage of the design of the longitudinal post tensioning is to obtain the stresses under the design loads and the required prestress determined by subtracting the allowable tensile stress from the design stress. Then, the optimal tendon spacing and the tensioning amount can be obtained by comparing with the effective tensioning amount including various stress losses.

• Tunnel and Underground Space
• /
• v.21 no.4
• /
• pp.307-319
• /
• 2011

Cyclic loading due to traffic, excavation and blasting causes microcrack growth in rocks over long period of time, and this type of loading often causes rock to fail at a lower stress than its monotonically determined strength. Thus, the crack growth and coalescence under cyclic loading are important for the long-term stability problems. In this research, experiments using gypsum as a model material for rock are carried out to investigate crack propagation and coalescence under monotonic and cyclic loading. Both monotonic and cyclic tests have a similar wing crack initiation position, wing crack initiation angle, cracking sequence and coalescence type. Three types of crack coalescence were observed; Type I, II and III. Type I coalescence occurs due to a shear crack and Type II coalescence occurs through one wing or tension crack. For Type III, coalescence occurs through two wing or tension cracks. Fatigue cracks appear in cyclic tests. Two types of fatigue crack initiation directions, coplanar and horizontal directions, are observed.

• Journal of the Korean Ceramic Society
• /
• v.38 no.6
• /
• pp.575-581
• /
• 2001

세라믹/금속기지 복합재료에서 횡방향의 단축인장하중을 받는 경우, 복합재료의 특성에 관한 시뮬레이션 결과이다. 세라믹과 금속기지간 계면에 강한 결합이 존재하는 복합재와, 계면에서의 결합이 약한 복합재의 두 경우에 대하여 횡방향 평균응력과 평균변형율에 대한 관계를 계산하였다. 복합재료의 미시역학적개념과 유한요소해석법을 적용하여 세라믹체적분율의 변화에 따라 각기 해석되었다. 본 연구에서 계산된 횡방향 탄성계수는 문헌에 알려져 있는 미시역학개념으로 유도된 식에 의한 횡방향탄성계수값과 잘 일치되었다. 계면에서 강한 결합이 있는 복합재와는 달리, 약한 결합의 복합재는 인장하중에 의하여 세라믹/금속계면에서 금속재료와 세라믹간의 분리가 발생된다. 이 분리는 전체복합재의 강성을 감소시키며, 금속의 부피분율이 감소될수록 (즉, 세라믹의 부피분율이 증가할수록) 횡방향 평균응력의 평균변형율에 대한 감소로 나타났다. 미시역학의 개념을 적용한 유한요소해석기법을 통하여, 이미 알고 있는 복합재 각 성분의 특성으로부터 복합재료의 계면특성과 횡방향특성을 예측할 수 있다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.25 no.4
• /
• pp.301-305
• /
• 2012

In this work the mechanical behaviors of GaN nanowires are analyzed during tension, compression, and unloading deformations. The thermal conductivity of the nanowires at each deformed state is evaluated using an equilibrium Green-Kubo approach. Under tensile loading, the [0001]-oriented nanowires with hexagonal cross-sections undergo a phase transformation from wurtzite to a tetragonal structure. The phase transformation is not observed under compressive loading. The thermal conductivity decreases on going from compressive strains to tensile strains. The strain dependence of the thermal conductivity results from the relaxation time of phonon. A reverse transformation from the tetragonal structure to the wurtzite structure is observed during unloading. The thermal conductivities in the intermediate states are lower than the conductivity in the wurtzite structure at same strain. Such differences in the thermal conductivity between different atomic structures are mainly due to changes in the group velocity of phonon.