• Korean Journal of Materials Research
• /
• v.7 no.7
• /
• pp.592-596
• /
• 1997

LI$_{2}$형 결정구조를 갖는 Ni-20at.%AI-10at%Fe 금속간화합물에 boron, zirconium 과 hafnium을 최고 0.5at.% 까지 첨가하여 항복강도, 연성, 파괴 등 기계적 성질의 변화를 인장시험과 X선분석 및 XPS분석 등을 통하여 관찰하였다. Ni-20at.% AI-10at.% Fe금속간화합물에 boron을 첨가하였을 때는 연신율의 현저한 증가가 나타났으나 zirconium이나 hafnium첨가의 경우에는 별다른 효과가 나타나지 않았다. Ni-20at.%AI-10at%Fe 금속간화합물의 경우, boron의 양이 증가할수록 인장연신율이 증가하였으며 0.1at.%의 boron을 첨가한 경우 최고 48.5%의 상온인장연신율을 나타내었다. 첨가물을 넣지 않은 경우와 zirconium과 hafnium을 첨가한 경우, 파괴모드는 입계파괴의 형태를 나타내었으나 boron을 첨가한 경우에는 파괴모드가 입계파괴에서 입내파괴로 변화되었다. XPS분석을 통하여 boron이 입계에 편석된 것을 관찰할 수 있었으며 이는 이미 제시된 여러가지 해석들과 일치하는 결과이다. 이로부터 boron의 첨가에 따른 인장연신율의 증가는 boron의 입계편석거동과 관련이 있음을 알 수 있다.

• Journal of the Korean GEO-environmental Society
• /
• v.18 no.12
• /
• pp.5-11
• /
• 2017

The 19 mm-sized aggregate was produced by melting vinyl waste (waste polyethylene film) generated from vinyl greenhouses in rural areas. It was mixed with As'cone at various weight ratios, and then insulation effect test, tension test after repeated freezing and thawing, ice pull-out strength test and field density test were conducted for the mixtures. These results demonstrated that as the mixing ratio of polyethylene aggregate increased, the insulation effect increased, due to the many pore spaces that existed in the polyethylene aggregate. After repeatedly freezing and thawing As'cone, the tensile strength significantly increased at 2.5% of the polyethylene aggregate content rather than 0% of polyethylene aggregate content but it also slightly decreased at 5% and 10% of polyethylene aggregate content in comparison to 2.5% of its polyethylene aggregate content. As'cone added with polyethylene aggregate by 2.5% resulted in lower ice pull-out strength than that of normal As'cone. As a result of the porosity test for the samples taken at the site, porosity of the As'cone, which added polyethylene aggregate, was smaller than that of the general As'cone.

• Journal of the Korea Institute of Building Construction
• /
• v.19 no.6
• /
• pp.485-494
• /
• 2019

This study is to evaluate the effect of admixtures such as blast-furnace slag and fly ash on adhesion in flexure and tension of polymer cement mortar(PCM) using SAE emulsion. The test specimens are prepared with five polymer-cement ratios and five admixture contents, and tested for flexural strength, adhesion in flexure, tensile strength and adhesion in tension. Based on the test results, no improvement of flexural strength and adhesion in flexure caused by admixtures in PCM can be indicated, but the tensile strength and adhesion in tension is improved due to mixing of the admixtures. In particular, the maximum of adhesion in tension of PCM with P/C 20% and BF content of 10% is 3.35MPa which is about 2.36 times higher than that of ordinary cement mortar, and 1.32 times that of PCM that does not contain any admixture. The average ratio of adhesion in tension to tensile strength of PCM was 48.7%. It is apparent that admixture contents of 5% or 10% could be proposed for improvement of tensile strength and adhesion in tension of PCM.

• Tunnel and Underground Space
• /
• v.29 no.5
• /
• pp.346-355
• /
• 2019

When evaluating pillar stability in very closely spaced tunnels, a local safety factor (strength/stress ratio) at the minimum width has been widely used. Tension bolts have been frequently applied as reinforcement for the cases where safety factors are less than 1.0 from FEM stress analysis. However, the local safety factor shows a constant value irrespective of the change in pillar width/tunnel diameter (PW/D) and the safety factor of the pillar is underestimated because the variation of deviation stress is relatively small even when the pre-stressing is applied to the tension bolt. In addition, the average safety factor proposed by Hoek and Brown(1980) was reviewed, but the pillar safety factor was relatively overestimated when the width of the pillar was increased. As an alternative, the SRM safety factor using shear strength reduction method shows the effect of changing the safety factor in the case of no reinforcement and tension bolt reinforcement as the pillar width/tunnel diameter(PW/D) changes. The failure shape is also similar to the previous limit theory result. In this study, the safety factor was evaluated without considering rock bolt and shotcrete to distinguish reinforcing effect of tension bolt.

• Resources Recycling
• /
• v.22 no.3
• /
• pp.50-56
• /
• 2013

Recycled plastic composites of ABS/PE (50/50 and 20/80) and ABS/GF (90/10) were fabricated from plastic components of waste LCDs and effects of PE composition on elongation of ABS/PE composites were investigated. Increased PE contents improved elongation of the composite from 2.4% to 13%, which was attributed to increased crystalline behavior of the ABS/PE composite afforded by ductile PE fraction: SEM fractographs showed some sign of plastic deformation of PE matrix before ductile fracture of the composites.

• Journal of the Korea Concrete Institute
• /
• v.14 no.3
• /
• pp.315-320
• /
• 2002

The effects of slag content and polymer-binder ratio on the strength properties of the polymer-modified concretes using ground granulated blast-furnace slag and a styrene-butadiene rubber (SBR) latex are examined. As a result, the compressive, tensile and flexural strengths of the SBR-modified concretes using slag increase with increasing polymer-binder ratio and slag content, and maximized at a slag content of 40 ％. In particular, the SBR-modified concretes with a slag content of 40 ％ provide approximately two times higher tensile and flexural strengths than unmodified concretes. Such high strength development is attributed to the high tensile strength of SBR polymer and the improved bond between cement hydrates and aggregates because of the addition of SBR latex.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.37 no.3
• /
• pp.240-245
• /
• 2001

The tensile strength and failure mechanisms of glass fiber polypropylene (GF/PP) composites are investigated in the temperature range from ambient to 8$0^{\circ}C$. The tensile strength increases as fiber volume fraction ratio increase. The tensile strength shows a maximum at ambient temperature, and it tens to decrease as temperature goes up. Major failure mechanisms of GF/PP composites can be classified as fiber matrix debonding, fiber pull-out, delamination and matrix deformation.

• Proceedings of the Korean Society of Fisheries Technology Conference
• /
• 2003.05a
• /
• pp.64-65
• /
• 2003

열경화성 수지를 사용한 복합재료의 연구결과들을 종합하여 보면 인장강도에 영향을 미치는 인자에 대한 다양한 연구결과가 있으나, 섬유함유율과 온도에 따른 인장파괴기구에 대한 고찰은 아직 희박한 실정이다. 따라서 이 연구에서는 열가소성 복합재료의 기계적 특성과 파괴거동에 관한 종합적인 연구의 일환으로 섬유함유율이 10%인 GF/PE 복합재료를 -5$0^{\circ}C$에서 6$0^{\circ}C$사이의 온도범위에서 인장시험을 통하여 임계 파괴에너지의 거동을 고찰하고, 각각의 온도범위에서의 파단면을 SEM사진을 통해 비교 검토하였다. (중략)

• Journal of Korea Foundry Society
• /
• v.44 no.3
• /
• pp.59-69
• /
• 2024

The tensile properties of the single crystal superalloy CMSX-4 were examined at various temperatures. In the heat-treated state, some portion of the eutectic γ-γ' remained, and a uniform cuboidal γ' particles existed across the entire material. The yield strength and tensile strength reached highest at 750℃ and decreased with raising testing temperature. The elongation was lowest at 650℃ due t℃oncentrated deformation near the fracture area. However, the elongation increased at higher temperatures due to uniform deformation throughout the entire specimen. Fracture surface analysis tested at 850℃ and 950℃ revealed that cracks originated from casting defects. TEM observations conducted after the tensile test indicated that the primary deformation mechanism at room temperature involved dislocation shearing within the γ' phase. However, the increased strength both at 750℃ where stacking faults generated and at 650℃ was caused by the increased resistance of γ' phase to dislocation. The strength decreased because the movement of dislocations became easier due to the thermal activation process at and above 850℃.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.1
• /
• pp.147-153
• /
• 2019

The prestressing steel wire, which is applied a tension to reinforce the structure, is applied flexure simultaneously by the duct and the deviator. In order to evaluate the deflected tensile performance of the prestressing steel wire subjected to both tensile and flexural stresses, the numerical analysis for 600 cases with variables of wire diameters, mandrel diameters, and friction coefficient between mandrel and steel wire was performed. As the result of analysis, the larger the diameter of the steel wire was, the lower the deflected tensile performance was, and the effect decreased with the increase of the wire elongation. The effect of mandrel diameter and friction coefficient between mandrel and wire on the deflected tensile performance of the wire was very small. But the deflected tensile performance and the friction coefficient between mandrel and strand showed a relatively high correlation. Therefore, it is necessary to make enough large elongation to secure the deflected tensile performance. If there is a restriction on the elongation, it is necessary to reduce the diameter of the steel wire to an appropriate value, and to increase the friction between steel wires by adjusting the surface condition of the steel wire.