• Journal of the Korean Society of Propulsion Engineers
• /
• v.1 no.1
• /
• pp.104-110
• /
• 1997

To predict the effect of ring expansion and ring compression on residual stress relief of Al 7175 ring rot]s, 2-D axisymmetric thermal analysis and elastoplastic analysis were performed. The residual stress distributions along the thickness of T73, T7351 and T7352 treated rings were measured using three step sectioning method. The measured results were compared to numerical ones for quenched and stress relieved rings. After quenching, calculated hoop and axial residual stresses were similar to measured ones for T73 treated rings. The residual stresses of T7351 and T7352 treated rings were decreased remarkably compared to T73 treated rings. The effect of axial residual stress relief was superior to that of hoop one, and also ring compression to ring expansion. It was concluded that ring compression is advantageous over ring expansion in view of stress relief effect and practicality, and vice versa in view of dimensional control and press power.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.2
• /
• pp.25-36
• /
• 1999

The main objectives of this research are to experimently explain the drilling mechanism for the production of bad holes and good holes during the drilling operation, to investigate how a wide range of drilling parameter affect composite laminate strength reduction, and to find which type of test provides the greatest interrogation of notched composite laminates. To achieve these objectives, a bulk of test specimens have been drilled with 5 different drilling parameters and tested with compressive, tensile, and flexural loads. It was found that the drilling parameters had a measurable effect on specimen hole quality as measured by static strength. The specimens, which were well supported, which had the higher spindle speed and lower feed rate, and which were well clamped gave the best hole qualities. The flexural test results presented the most clear and consistent failure strengths relating to the drilling parameters and associated hole quality.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2001.04a
• /
• pp.184-184
• /
• 2001

캘린더령은 지펼의 표면을 평활하게 하고, 두께를 감소시켜 균일하게 하는 역할을 한다. 그러나 이는 필연적으로 불투명도와 같은 광학적 성질과 인장강도 등의 강도적 성질 의 저하를 유발한다. 따라서 캘린더링 공정변수인 온도, 압력, 속도 등이 종이의 물성에 미 치는 영향을 정확하게 파악하는 것은 캘린더령에 따라 발생할 수 있는 물성 저하를 최소화 하기 위해 필수적으로 요청된다. 본 연구에서는 최근들어 저평량화에 대한 관심이 증가하면 서 그 중요성이 더해지고 있는 불투명도가 캘린더링에 따라 변화되는 양상을 분석하기 위해 서 화상분석 기법을 이용하여 종이의 두께방향 밀도 변이를 평가하고 밀도변이와 불투명도 와의 상관관계를 해석코자 하였다. 또 캘린더링에 따른 불투명도를 저하를 최소화시키기 위 한 캘린더링 조건을 모색하였다. 캘린더링에 의해 발생하는 종이의 두께 변형은 두께방향의 위치에 따라 다르게 나 타난다. 이러한 종이의 두께 방향으로 발생하는 밀도 변이와 이에 따른 불투명도 변화를 평 가하기 위하여 동일한 평량의 종이를 캘린더령 조건을 달리하여 두께방향 밀도변이가 다른 시편을 준비하고 두께 방향 단면을 SEM으로 촬영하였다. 이후 화상분석기를 통해 단면을 이치화하고, 각 픽셀의 흑백 값을 구해 CD방향으로 평균을 내어 두께 방향에 대한 밀도 변 이를 평가하였다. 그 결과 압력보다는 온도를 높여 캘린더링한 경우 종이의 두께 방향 밀도 경사가 커진다는 사실을 확인할 수 있었다. 이는 고온에 의해 표층이 고밀화되고 상대적으 로 내부가 별크해졌기 때문이다. 이러한 밀도 변이가 종이의 광학적 성질인 불투명도에 미 치는 영향을 구명하기 위해서 캘린더링 전후에 두께 및 불투명도를 측정하여 5% 유의수준 에서 회귀분석을 실시하였다. 밀도경사를 지닌 종이의 불투명도를 이론적으로 해석하기 위해 다층 모델을 가정하 고 각 층의 비광산란계수(5)와 비광흡수계수(k)를 달리 부여하고 Kubelka-Munk 이론을 근 거로 하여 이론적 불투명도를 계산하였다. 불투명도에 대한 분석를 통해 동일한 두께 변형 을 가지는 샘플에 대해서 압력보다는 온도를 증가시켜 두께를 감소시키는 캘린더링 처리가 불투명도의 저하를 최소화한다는 것을 확인하였다.

• Tunnel and Underground Space
• /
• v.24 no.1
• /
• pp.67-80
• /
• 2014

Long-term stability and delayed failure of granite were evaluated through the laboratory test based on Wilkins method and Brazilian disc test (BDT) which yields tensile strength, mode I fracture toughness and subcritical crack growth parameters. Then, the long-term strength of granite was estimated by using analytical models and long-term stability of compressed air-energy storage (CAES) pilot cavern pressurized up to 5 ~ 6 MPa was evaluated using numerical code, FRACOD with the determined subcritical crack growth parameters. The results of test and analyses showed that the subcritical crack growth index, n was determined as 29.39 and the inner pressure of 5 ~ 6 MPa had an insignificant effect on the long-term stability of pilot cavern. It was also found that the measurement and analysis of acoustic emission events can describe the accumulation of damage due to subcritical crack growth quantitatively. That is, AE monitoring can provide the current status of rock under loading if we make an identical installation condition in the field with that of the laboratory test.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.53-56
• /
• 2003

The disappearance of continuous yielding and the formation of an extended region in engineering stress-strain curves at tempering temperatures of 673-873K is closely related to the reduction of mobile dislocations during tempering and dynamic recovery during tensile deformation. In addition, the occurrence of discontinuous yielding at tempering temperature above 923K would be attributed to the formation of new strain-free polygonal ferrite grain.

• Transactions of Materials Processing
• /
• v.12 no.8
• /
• pp.744-749
• /
• 2003

The effect of tempering temperatures on microstructures and mechanical properties was studied in a low carbon steel. The disappearance of continuous yielding and the formation of an extended region in engineering stress-strain curves at tempering temperatures ranging from 673 to 873K was caused by the reduction of mobile dislocations during tempering and dynamic recovery during tensile deformation. In addition, the occurrence of discontinuous yielding in the sample treated at the tempering temperatures above 923K was attributed to the formation of new strain-free polygonal ferrite grain.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.322-327
• /
• 2003

In this study, the single notched specimen which was proposed the previous study was used to evaluate of the transverse tensile property of zircaloy cladding. The single notched specimen has notches which give stress intensity effect, so both FEM and experiment are needed for the same time. Take a coincidence of tensile behavior about both FEM and experiment, then obtain stress and strain from FEM only. The influence of notch was estimated by comparing the result of experimental, FEM. Then the relationship between stress-strain and displacement was evaluated.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.1
• /
• pp.98-105
• /
• 2008

In this paper, the system for monitoring process of aluminum laser welding was developed using the light signal emitted from the plasma which comes from interaction between material and laser. Photodiode for monitoring system was selected based on the spectrum analysis of light from plasma and keyhole. Behavior of plasma and keyhole was analyzed through the sensor signals. Value of sensor signal represented the light intensity and fluctuation of signal indicated the stability of plasma and keyhole. For the relation between welding condition and sensor signals, the input power and weld geometry greatly effected on the average of each sensor signals. Using the feature values of signals, estimation model for tensile strength of weld was formulated with neural network algorithm. Performance of this model was verified through coefficient of determination and average error rate.

• Laser Solutions
• /
• v.2 no.1
• /
• pp.38-42
• /
• 1999

As very large scale integration technology has been developed, much more accurate, reliable technology is needed for outer lead bonding. Laser soldering has been researched as an alternative for fine pitch device bonding. This study is focused on how to select optimal laser soldering variables with which solder wets parent material, the microstructural results of laser soldering and the reliability test One of popular packages, QFP100 was soldered successfully with two kinds of solder. The inspection of the joint for reliability was carried out by optical microscope, SEM, EDAX and pull test, which demonstrated the superiority of laser soldering.

• Proceedings of the KAIS Fall Conference
• /
• 2010.05b
• /
• pp.773-776
• /
• 2010

일반적으로 자동차의 내장부품인 콘솔박스에 가죽을 입히는 커버링 작업은 가죽을 일정한 힘으로 인장한 후 정확한 비율로 씌워야 하는데 가죽의 신축과정에서 어려움이 있고 현재 제품의 생산 공정은 10개의 수작업 공정을 필요로 하며 이로 인해 제품의 품질 편차가 일정하지 못하고 생산량의 변동이 심하며, 작업자의 잦은 부상 및 이직, 늦은 작업 속도에 의한 생산원가의 상승 등의 문제가 발생하고 있다. 이를 위하여 본 연구는 상기 10개의 수작업 공정을 1개의 자동화 공정으로 단축시지는 자동화 시스템의 구동 메커니즘 설계 및 제품에 대한 해석을 행하며 자동화 장비 시작품을 제작하여 성능을 분석한다.