• Proceedings of the Korea Water Resources Association Conference
• /
• 2010.05a
• /
• pp.1089-1093
• /
• 2010

최근 하천의 자연성 및 생태기능의 향상을 위해 매트류 호안공법의 적용이 증가하고 있다. 이러한 공법이 적용된 호안은 강수 및 하천수의 지속적인 유입으로 인해 앵커핀과 비탈면 간의 마찰력을 저하시킬 수 있다. 마찰력의 저하는 앵커핀의 고정능력을 저하시켜 매트가 들뜨는 현상을 발생시키고, 이로 말미암아 비탈면에 식재된 식생의 고사는 물론 비탈면의 슬라이딩 현상의 발생에 의해 비탈면 붕괴에 까지 이르게 하고 있다. 그러나 현재 호안매트와 함게 시공하는 앵커핀의 적용에 대한 구체적인 기준과 연구가 미흡한 실정이다. 본 연구에서는 매트류 호안제품을 비탈면에 고정시키는 목적으로 사용하고 있는 앵커핀에 대한 인발특성을 파악하고자 하였다. 인발실험에 사용된 앵커핀은 실제 하천호안에 적용되고 있는 상용제품으로 형태가 다른 4가지 type을 실험에 사용하였으며, 앵커핀의 관입깊이(170mm, 250mm) 별로 인발실험을 실시하였다. 실험에 사용된 인발장치는 인발부에 로드셀을 장착하여 앵커핀과 결합이 가능하도록 하였으며, 인발시 발생하는 계측 값을 컴퓨터를 통해 출력이 가능하도록 제작하였다. 실험결과 4가지 형태의 앵커핀에 대한 관입깊이별 형태별 인발특성을 파악할 수 있었으며, 비탈면 및 매트의 고정효과가 우수한 앵커핀의 형태에 대해서도 파악할 수 있었다. 관입깊이별 최대 인발력은 두 변위(170mm, 250mm) 모두 Type 4가 337N, 594N 으로 가장 큰 인발력을 가지는 것으로 측정되었으며, 변위에 의한 인발력의 증가는 Type 2가 138%로 가장 큰 폭의 증가 값을 보였다. 또한 토양과 앵커핀의 마찰력 향상을 위해 하부가 돌출된 형태로 제작된 Type 2와 Type 4가 상대적으로 실험 후반부에서 최대 인발력이 발생하고 인발지속시간이 길게 나타나는 것으로 볼 때, 인발저항은 앵커핀 하부의 돌출면적에 영향을 받는 것으로 판단된다.

• Journal of the Korean Geosynthetics Society
• /
• v.22 no.4
• /
• pp.27-34
• /
• 2023

This paper describes the results of a pile pullout test considering the confine pressure and fines content of the ground. The Pullout tests were conducted under various ground conditions using model piles. The effect of ground confine pressure on the pullout resistance and the pullout resistance parameters of the pile were evaluated based on the experimental results. The results of pullout test showed that the maximum pullout resistance occurred at a pullout displacement of about 7mm to 9mm, regardless of the fines content and the confine pressure of the ground. The maximum pullout resistance of the pile decreased as the fines content of the ground increased, and this trend became clearer as the confine pressure increased. The pullout resistance calculated by theoretical formula was compared with the experimental results in order to ensure the reliability of the pullout test results. The comparative results showed that the experimental and theoretical values showed a tendency to decrease the pullout resistance as the fines content increased, in all confine pressure conditions. The analysis result of the pullout resistance parameters confirmed that the pullout resistance was greatly influenced by the adhesion compared to the interface friction angle, as the fines content of the ground around the pile increased.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.319-324
• /
• 2011

최근 자연환경보전이라는 새로운 패러다임의 대두로 하천의 생태기능 향상을 위한 호안조성공법 중 하나인 식생매트호안 공법의 적용이 증가하고 있다. 국내 하천의 경우 비교적 큰 하상계수와 소류력의 증가로 식생매트 고정용 앵커핀의 기능 저하에 따른 호안의 피해가 발생하고 있다. 그러나 앵커핀의 외력저항성 연구 및 설치를 위한 기준이 마련되어 있지 않는 실정이다. 본 연구에서는 앵커핀의 인발특성을 연구함으로서 외력저항 특성을 파악하고자 하였다. 연구방법으로는 앵커핀을 관입시킨 토사에 인발장치를 연결하여 최대인발력과 인발력의 변화추이를 관찰하였다. 실험에 사용된 토사는 물다짐으로 다졌으며, 앵커핀은 식생매트 고정용으로 적용이 많은 이형철근형 앵커핀을 사용하였다. 대조군으로 형태가 동일한 원형철근을 이용하여 앵커핀을 제작 실험에 사용하였다. 실험조건은 앵커핀의 직경(10mm, 16mm)에 따른 주면과 침수토사의 배수시간 (48hr, 96hr, 144hr) 조절을 통한 함수율의 변화에 따른 인발특성을 관측하였다. 실험결과 평균 최대인발력의 변화는 48시간 배수시 직경변화에 따라 이형철근은 12.8N, 28N, 원형철근은 10.6N, 21N으로 나타났으며, 96시간 배수시 이형철근은 18.8N, 33N, 원형철근은 12.2N, 21.6N으로 나타났고, 144시간 배수시 이형철근은 21.4N, 36.4N, 원형철근은 20.4N, 33.2N으로 나타났다. 앵커핀의 인발력은 주면의 크기에 비례하며, 표면의 형태와 함수량에 따라 영향을 받는 것으로 나타났다. 따라서 이러한 앵커핀의 인발 특성을 파악하고, 식생호안에 적용한다면 피해를 최소화 할 수 있을 것으로 사료된다.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.1
• /
• pp.121-133
• /
• 2013

This paper presents the results of an investigation into the pull-out capacity characteristics of screw anchor piles. Theoretical background of screw anchor pile (SAP) was first discussed. A series of reduced-scale model tests were performed on a number of cases with different SAP geometries such as pitch and diameter of screw as well as relative density of the model ground. The applicability of the pull-out capacity prediction equations were also examined based on the test results. It was shown that the pitch of screw has negligible effect on the pull-out capacity, while the diameter of screw has relatively large effect on pull-out capacity under a given condition. Practical implications of the findings from this study are discussed in great detail.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.13 no.1
• /
• pp.71-82
• /
• 2011

This paper presents the tensile strength of shotcrete steel fibers depending on the shape of steel fiber. The experimental and numerical analyses are performed in this study. In experimental study, a series of laboratory pullout tests are carried out by changing both the angle and the length of the embedded steel fiber according to the corresponding type of steel fiber in order to derive the optimal type of steel fiber. Results obtained from the experimental work are evaluated and compared with the numerical analysis results. The results clearly show that the pull-out strength of the steel fiber are increased with increasing the hook angle and embedded angle of steel fiber. It is also found that the pull-out strength of the steel fiber is larger in case of the short steel fiber body length.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.11
• /
• pp.27-37
• /
• 2011

A series of centrifuge model tests to investigate the suction pile pullout loading capacity in sand have been performed. The main parameters that affect the pullout loading capacity of a suction pile include the mooring line inclination angle and the padeye position of the suction pile. With respect to the padeye position, the maximum pullout loading capacity is obtained when the padeye position is near 75% of the pile length from the top. The direction of the pile rotation changes when the padeye position reaches somewhere near 50~75% for all mooring line inclination angles. The translation displacement of suction pile to develop the time of maximum pullout loading capacity decreased as the mooring line inclination angle increased. In addition, the vertical displacements of the center of a suction piles for all cases appeared to develop toward the ground surface.

• Journal of the Korea Concrete Institute
• /
• v.25 no.5
• /
• pp.547-554
• /
• 2013

This study was intended to estimate the bond strength of steel fiber in UHPFRC through pullout test. The pullout test was carried out with the double-sided pullout specimens with multiple fibers. First, the effect of fiber density on the bond strength was investigated, and the experimental result presented that the density range considered in this study was proved not to produce fiber-to-fiber interaction. The bond strength was estimated from several methods, which are based on the pullout load or energy at peak load, and the total energy absorbed until fibers are pulled out completely. the estimated bond strength obtained from the total energy was shown to be under the influence of the embedded length of fiber. the bond strengths obtained from peak load condition was 6.64 MPa in average, which had little difference compared to 6.46 MPa calculated by peak load only. Considering simplicity of test and analysis, it may be no matter to estimate the bond strength from peak load in pullout test.

• Journal of the Korea Institute of Building Construction
• /
• v.22 no.2
• /
• pp.149-160
• /
• 2022

In this study, a pull-out test considering the adhesive type, embedded length, and direction of re-bar was conducted to evaluate the pull-out performance of glued-in rod joints using timber and adhesive produced in Korea. In the test, the specimens using liquid adhesive showed better pull-out performance, and the longer the embedded length of the re-bar, the higher the maximum tensile load by inducing the yield of the re-bar first. Through the test results, a glued-in rod joints design, which is advantageous to design the adhesive strength stronger than the yield strength of re-bar, was proposed, and a correction factor of 0.75 for the adhesive strength considering construction error was also suggested.

• Journal of the Korea Concrete Institute
• /
• v.19 no.3
• /
• pp.323-331
• /
• 2007

The development length equations of the GFRP rebars are suggested based on the pullout tests performed in this study. A total of 48 pullout and modified pullout tests were completed. Test variables included embedment length (L=10, 15, 20, and $30d_b$), vertical and horizontal installation of the rebars, height of the rebars (H=100 and 300 mm), and cover thickness $(C=2{\sim}5d_b)$. D13 GFRP rebars domestically developed were used in the experimental program. The average of the bond strength of all vertically installed GFRP rebars was 6.39 MPa with a 5% fractile of 4.63 MPa. A basic development length equation was derived that resulted in an equation equivalent to the one proposed in the ACI 440.1R-03. Careful reevaluation of the bond strength using the modified pullout test indicated that a modification of the design equation was necessary so that the basic development length increases by 11%. The top bar effect of the horizontally installed rebars as well as the effect of the cover thickness were determined and included in the set of suggested equations. Since the current equations were derived from testing rebars embedded in relatively low strength concrete $(f_{ck}=20{\sim}24MPa)$, they result in conservative development lengths when applied to bars embedded in higher strength concretes.

• Journal of Bio-Environment Control
• /
• v.10 no.3
• /
• pp.148-154
• /
• 2001

The uplift capacity of a pile for improving the wind resistance of the 1-2 W type plastic film pipe on greenhouses was tested using the plane and corrugated piles with various shapes and diameters. First, the resistant uplift capacity was measured by using the uplift loading on plane piles. As the uplift loading on plane piles increased, the resistant uplift capacity also increased until the loading was reached to ultimate uplift capacity. After ultimate uplift capacity was appeared the uplift displacement, the uplift capacity was decreased gradually. Secondly, the resistant uplift capacity was measured by using the uplift loading on corrugated piles. After the uplift capacity was reached the uplift displacement, the uplift capacity was continually increased or decreased. In general, the ultimate uplift capacity was independent of pile shapes, pile diameter length, and embedded pipe depth. However, the ultimate uplift capacity of a corrugated pile was twice more than that of a plane pile without regard to its diameter and embedded depth. The ultimate uplift capacity per unit pile area was increasing in deeper embedded depth. However, the longer a pile diameter was, the less ultimate uplift capacity. The uplift capacity of a plane pile, used in conjunction with the design wind velocity (26.9m.s$^{-1}$ ) of the project area, was unsatisfiable without regard to diameters and embedded depths of piles, while most of corrugated piles were well appeared uplift capacity under various experimental conditions.