• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.950-952
• /
• 2000

Considering the effective distribution coefficient of Ni in Fe-Ni-Co invar alloy containing a little amount of carbon, we investigated on the thermal expansion coefficient(${\alpha}$). Fe-Ni-Co invar alloy had a large thermal expansion coefficient in as-casted compared with solution treated. The thermal expansion coefficient of Fe-Ni-Co alloy increased with the carbon content in both state of as-casted and solution treated. The effective distribution coefficient(Ke$\^$Ni/) of Ni was smaller than unity in alloy of not containing carbon, but is way larger than unity in alloy of containing carbon. It was considered that the homogeneity of Ni in primary austenite affected thermal expansion coefficient.

• Journal of the Korean Magnetics Society
• /
• v.3 no.1
• /
• pp.7-12
• /
• 1993

The effects of Mn, Cr or Co addItion on the magnetic properties of Fe-Ni Invar alloys were investigated. The composition range of the three additives is up to 5wt%. In the temperature range of room temperature-$250^{\circ}C$, the variation of specific magnetization with the addition of Mn, Cr or Co in the Fe-Ni alloys except for 5wt% Co shows the phenomenon characteristics of the Invar effect, viz., the specific magnetization decreases very abrubtly with the temperature and the dependence of temperature on the specific magnetization is in the mixed form of $T^{3/2}$ and $T^{2}$. In the room temperature, the amount of increase in the specific magnetization, Curie temperature and coercivity is in order of Co > Cr > Mn. In the case of 5wt% Co an anomalous phenomena were observed due to the occurrance of ferromagnetic $\alpha$ phase which reduces the invar effect.

• Journal of the Korean Vacuum Society
• /
• v.10 no.2
• /
• pp.201-206
• /
• 2001

The evolution of textures in Fe-Ni alloy thin films fabricated by PVD using a sputtering method was investigated with parameters such as deposition time and chemical composition. The textures of the as-deposited films were characterized by fibre-type. In Invar alloy(Fe-36.5 wt%Ni) thin film, the <110>//ND fibre texture as a starting component changed to the <210>//ND fibre texture with increasing deposition time. In Permalloy(Fe-81 wt%Ni) thin film, a mixture of the <221>//ND and <311>//ND fibres developed at the early stage of deposition, and then transformed to the <210>//ND fibre with increasing deposition time. These texture changes were discussed in terms of relationship with the microstructural evolution of the films.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1993.02a
• /
• pp.80-80
• /
• 1993

• 전기산업
• /
• v.12 no.11
• /
• pp.22-27
• /
• 2001

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2005.11a
• /
• pp.164-165
• /
• 2005

• Proceedings of the Korean Magnestics Society Conference
• /
• 1993.03a
• /
• pp.52-53
• /
• 1993

• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.1
• /
• pp.39-43
• /
• 2013

The experiments were carried out in the variation of current density, pH, temperature, and duty cycle to investigate the influence of electroplating parameters on the properties of Ni-Fe invar alloys. When the current density and temperature were changed, the composition of invar alloy was varied, however, duty cycle and pH hardly affected on the composition of electrodeposited alloys. However, as the duty cycle was increased, microstructure was changed and the decrease of hardness was also observed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.560-563
• /
• 2004

Invar is a compound metal of Fe-Ni system and contain 36％ Ni. The most distinction characteristic of Invar is the coefficient of thermal expansion is 1.0 10$^{-6}$ /$^{\circ}C$. That is a tenth of general steel material. This low thermal expansion characteristic of Invar is applied to the missile, aircraft, monitor CRT and frontier display's shadow mask such as FED and OLED. The usage of the Invar shadow mask for display is increasing due to the requirement of larger size and flatness monitor. The Invar shadow mask is machined by two ways electro-forming and laser now. However the electro-forming takes a too long time and the laser machining is accompanied with Burr. In this study, PEMM(pulse electrochemical micro machining) is conducted to machine the micro hole to the Invar and 80${\mu}{\textrm}{m}$ hole was machined.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.10a
• /
• pp.147-147
• /
• 2009

Shadow mask는 OLED의 R-G-B 컬러를 구현하기 위한 유기화합물을 증착하는데 사용하는 금속막으로 수없이 많은 홀이 뚫려있고 디스플레이의 화질, 선명도 및 색상을 좌우하는 핵심적인 소모성 부품이다. 하지만 증착공정시 발생되는 열에 의해 홀의 치수변화가 발생되기 때문에 이를 방지하기 위하여 본 연구에서는 열팽창에 치수변화가 없는 인바소재를 이용하여 Shadow mask를 제조하였다.