• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.3
• /
• pp.216-223
• /
• 2006

The high efficiency full-bridge LLC resonant converter using a contact-less transformer Is proposed for the photovoltaic power generation system. For the series resonance with a series capacitor, the LLC resonant converter utilizes the leakage inductance and magnetizing inductance of a contact-less transformer Unlike the conventional series resonant converter operated to the continuous resonant current at above resonance frequency, the proposed converter operates to the discontinuous resonant current at the narrow frequency control range below resonance frequency. Due to the discontinuous mode resonant current, the proposed converter can be achieved the zero voltage switching (ZVS) in the primary switches and the zero current switching (ZCS) in the secondary rectification diodes without my auxiliary circuit. In this paper, the experimental results of the proposed full-bridge LLC resonant converter using a contact-less transformer are verified on the simulation based on the theoretical analysis and the 150W experimental prototype.

• Journal of the Korean Magnetics Society
• /
• v.26 no.4
• /
• pp.137-141
• /
• 2016

There is a growing demand for non-contact current measurements for efficient use of electrical power and energy saving. In this study, I propose a non-contact current sensor using LC resonance by a resonance circuit composed of a sensor coil and 2 coupling coils for enabling a wireless measurement. The inductance of the sensor coil, which could be changed by applied current, causes the change of resonance frequency of the resonance circuit. A pair of magnet was attached to the ferrite core to apply a bias magnetic field that enabled the determination of the current direction. We obtained an output voltage change of 18 V with the current of -3~3 A. But, the output was nonlinear. In order to realize the non-contact current measuring method proposed in the present study, there is a need for a strict investigation of linearity and resolution for the future study.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.42 no.2
• /
• pp.7-14
• /
• 2005

This paper presents a method to reduce torque ripple of brushless DC motor by compensating phase delay due to winding inductance. For considering torque ripple comes from the phase winding inductance, torque equation of one phase is derived as Fourier series that is function of the delay. From the equation, also the resultant equation that the current delay is compensated is derived. It is validated that the compensated torque has a form of Fourier series for rectangular wave that is ideal torque, and torque ripple is reduced, consequently. Experimental method for the compensation is realized by replacing switching pattern of inverter by pattern of compensated rotor position. The effectiveness of the proposed method to reduce torque ripple has been demonstrated by the simulation and experimental results using 3 phase 4 pole brushless DC moor.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.3
• /
• pp.445-453
• /
• 2000

In this paper, the method of designing an active inductor for MMIC is proposed. The proposed tunable active inductor is composed of a cascade FET with feedback capacitors and resistors. Because of a very low series resistance in the proposed inductor, a very high Q factor can be obtained. Also it has an excellent characteristics suitable for high frequency band. The inductance value can be changed by controlling feedback capacitors, resistors and a bias voltage respectively. When the feedback resistor and parallel resistor within circuits are varied, the inductance value is changed from 0.2 nH to 1.7 nH in the range 1 to 15 GHz. Also we designed bandpass filter using the proposed active inductor and it shows the insertion loss of 0.4 dB and return loss, 20 dB.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.17 no.5
• /
• pp.22-28
• /
• 2003

This paper describes the frequency dependence of the grounding impedance. In order to propose the evaluation method of the transient response of powered grounding systems, the grounding impedances were measured with varying the frequency of incoming currents by way of the variable frequency inverter and band pass filter. The magnitude and phase of the grounding impedance were analyzed in the frequency range of 20 [Hz]∼2.1[kHz]. The grounding impedance were increased with increasing the frequency of the test current. The grounding impedance at the frequency of 2[kHz] in the actual 22.9[kV] substation grounding system was approximately 3 times as large as the 60[Hz] grounding impedance. It was found that the frequency dependence of the grounding impedance is mainly subject to the inductive reactance of the grounding conductors. As a result, it is critical to determine the shape and size of grounding grid reducing the resultant inductance in grounding systems for lightning surge protection.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.5
• /
• pp.405-412
• /
• 2004

In this paper, Non-contact power supply(NCPS) with the long primary cable longer than 20m and the large air-gap between the primary and secondary of Non-Contacting Transformer(NCT) is presented. The NCT has a large leakage inductance bigger than its magnetizing inductance because it has low coupling, and it is not efficient for NCPS to transfer the primary energy to the secondary one. In order to improve this problem, the voltage-gain characteristics of the series resonant converter, the parallel resonant converter, and the series-parallel resonant converter are analyzed respectively. In addition, the experimental results of 10kW prototype the series-parallel resonant converter is presented.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.3
• /
• pp.301-307
• /
• 2002

A multilayer ceramic chip antenna with helical structure is analyzed to enhance the narrow bandwidth of conventional ceramic chip antennas. The simulations are performed by HFSS to verify the effects of structural parameters on impedance bandwidth. The multilayer ceramic chip antennas consist of a rectangular-parallelepiped ceramic body$({\varepsilon}_r=7.8,\; tan\; {\delta}=0.0043)$ and helical conductor patterns are embedded in the ceramic body using LTCC-MLC technology. 3D structure design of the multilayer ceramic chip antenna suitable for IMT-2000 (1,920~2,170 MHz) handset has been implemented, and experimental results are presented and discussed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.287-287
• /
• 2008

HTS-케이블은 구리도체 대신 고온초전도도체를 사용하여 저항이 0이 되는 초전도현상을 이용하여 대용량 전력수송이 가능한 전력케이블로서 대도시의 전력부하 집중문제를 해결할 수 있는 환경 친화적 전력케이블이다. 최근 고온초전도선재의 고임계전류밀도화 및 장척화에 힘입어 HTS-케이블의 실용화를 목표로 경제성이 있는 전력케이블을 개발하려는 움직임뿐만 아니라 실증시험 등 활발한 연구가 진행 중이다. 그러나 초전도전력케이블에서 발생되는 교류손실은 케이블의 효율을 저하시킬 뿐만 아니라 냉동기비용 증가로 인한 기존 케이블과의 가격경쟁에서 경제성을 저하시키는 주된 요인으로 작용하기 때문에 이의 상용화에 앞서 교류손실에 대한 정확한 규명이 되어야 하며 또한 실계통 투입 시 중요한 선로임피던스에 대한 정확한 규명도 필요하다. 본 논문에서는 실제 한전 주관으로 고창시험장에 설치된 배전급 22.9 kV, 100 m, 50 MVA급 3 상 HTS-케이블에 대한 통전특성을 규명하기 위하여 먼저 HTS-케이블의 DC 통전특성을 조사하였다. 또한 3상평형운전상태에서 AC 통전특성(인덕턴스 및 교류손실)을 실험적으로 조사하였으며 5m-케이블에서 측정된 결과와 비교 검토하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.05b
• /
• pp.161-164
• /
• 2004

변압기는 권선방법에 따라 많은 특성의 변화를 나타내게 되는데 일반적인 동선의 권선법과 코일형태로 동판을 가공하여 사용하는 평면 권선방법, 그리고 고전류용 변압기에 이용되는 것으로 코어의 권선창 표면을 감싸는 형태의 관형 권선방법의 3가지의 코일 형태 또는 권선방법에 따른 변압기의 특성 변화와 컨버터에 채용되었을 때의 전력효율에 대하여 고찰하였다. 평면 코일을 이용한 변압기는 높은 코일간의 결합도로 인해 가장 낮은 누설인덕턴스와 가장 높은 성능지수 및 결합계수를 나타내었고, 관형코일을 이용한 변압기는 높은 누설특성으로 인해 가장 낮은 성능지수와 결합계수를 나타내었다. 그리고 이들을 DC-DC 컨버터에 채용하여 분석한 결과 평면변압기가 가장 높은 효율을 발휘하였다. 관형변압기는 저전력에서는 높은 누설량으로 인해 효율이 상대적으로 낮지만 출력전력이 증가할수록 상승하는 발열량에 대한 방열효과가 높아 효율의 감소폭이 작아서 고주파 또는 대전류용 변압기 응용이 기대된다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.10a
• /
• pp.238-240
• /
• 2017

Balun using a coaxial lines i often used in microwave circuits due to easy fabrication, high operating power, and stable operation. However, it is difficult to predict an accurate balun operation characteristic due to the parasitic reactance component to be generated when the coaxial line is connected to the microstrip line existing on the substrate, and the inductance and the capacitance component of the coaxial line itself. In this paper, it is measured the phase characteristics at two output ports of the coaxial line balun which should have opposite phase characteristics. Based on these results, it will examine closely the feasibility of making more improved coaxial line balun.