• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.3
• /
• pp.377-383
• /
• 1997

Yttria-stabilized TZP alloyed with pentavalent oxides $(Ta_2O_5,\;Nb_2O_5)$ were fabricated by the conventional sintering method at $1500^{\circ}C$ in air to construct the simplified ternary phase diagram. The phase stability of tetragonal -$ZrO_2$ from the quasi-binary system $ZrO_2-YTa(Nb)O_4$, which do not transform to monoclinic-$ZrO_2$ even for a wide range of grain size and annealing temperature, was investigated to determine composition region of the non-transformable $t-ZrO_2$ solid solution$(NT_{ss})$. Phase stability of $NT_{ss}$ was probably due to the enhanced stability of $_YTa(Nb)O4$ having the tetragonal fergusonite structure. It was experimentally found that mixtures having $NT_{ss}$ alloyed with $T_{ss}$ by weight%% showed both excellent phase stability of $t-ZrO_2$ and fracture toughness even though the calculated composition of the mixture /was located outside $NT_{ss}$ composition region.

• Transactions of the Korean hydrogen and new energy society
• /
• v.26 no.6
• /
• pp.516-523
• /
• 2015

Nickel based oxygen transfer materials supported on two different YSZs were tested to evaluate their performance in methane chemical-looping reforming. The oxygen transfer materials of YSZs were selected with different amount of the doped yittrium in the $ZrO_2$ structure. The yittrium of 8 mol% stabilized the zirconia oxide to a cubic structure compare to the 3 mol% doping, which is known to be a good for oxygen transfer. Various nickel amounts (16wt.%, 32wt.%, 48wt.%) were loaded on the selected supports. The nickel amount of 32% shows the optimized catalyst structure with good physical properties and reducibility from the XRD, BET and H2-TPR analysis, especially when the support of 8YSZ was used. From the methane chemical-looping reforming, hydrogen was produced by methane decomposition catalyzed by Ni on both YSZs. Comparing two YSZ supports of 3YSZ and 8YSZ during the cycling tests, the catalyst with 8YSZ (Ni 32%) exhibits not only the higher methane conversion and hydrogen production but also a faster reaction rate reaching to the stable point.

• Korean journal of applied entomology
• /
• v.37 no.1
• /
• pp.23-30
• /
• 1998

Restriction fragment length polymorphism (RFLP) of a DNA has been a useful tool for analyzing genetic variation. This research was performed to establish an RFLP analytic method on the mitochondrial DNA (mtDNA) of the beet armyworm, Spodoptera exigua (Hiibner). To do this, total size of the mtDNA was measured and polymerase chain reaction (PCR) primers were selected. Its mitochondrial genome size was ca. 16kb. From a serial PCR test of 29 primers refered to the compilation of Simon et al. (1994), 22 primers were selected to amplify its mtDNA fragments. These primers resulted in short (300-700 bp) or long (1000-2000 bp) DNA products which represented a total or partial sequence of each of CO-I, CO-11, Cyt-B, ND-1, 12s rRNA, 16s rRNA, and some tRNAs. PCR-RFLP was performed in some variable mtDNA regions with 8 kinds of 4bp recognizing restriction enzymes. Different populations from Andong, Kyungsan, and Sunchun did not show any restriction site polymorphisms but had some length variation in certain regions of mtDNA.

• Journal of Digital Convergence
• /
• v.13 no.12
• /
• pp.187-192
• /
• 2015

If the software is developed to analyze the speech disorder, the application of various converged areas will be very high. This paper implements the user-friendly program based on CART(Classification and regression trees) analysis to distinguish between normal and pathological voices utilizing combination of the acoustical and HOS(Higher-order statistics) parameters. It means convergence between medical information and signal processing. Then the acoustical parameters are Jitter(%) and Shimmer(%). The proposed HOS parameters are means and variances of skewness(MOS and VOS) and kurtosis(MOK and VOK). Database consist of 53 normal and 173 pathological voices distributed by Kay Elemetrics. When the acoustical and proposed parameters together are used to generate the decision tree, the average accuracy is 83.11%. Finally, we developed a program with more user-friendly interface and frameworks.

• Journal of Sensor Science and Technology
• /
• v.1 no.1
• /
• pp.93-100
• /
• 1992

Sinterability, mechanical and electrical properties of yttria-stabilized zirconia(92 mole% $ZrO_{2}$+8 mole% $Y_{2}O_{3}$) doped with 0.5 mole% $SiO_{2}$ and $0{\sim}2.0 mole%{\;}Al_{2}O_{3}$ were studied as a function of $Al_{2}O_{3}$ addition. Sintered density increased with increasing $Al_{2}O_{3}$ addition up to 0.5 mole % but leveled off with further addition. Victors hardness is proportional to sintered density. The specimen with 0.5 mole% $Al_{2}O_{3}$ and 0.5 mole% $SiO_{2}$ exhibited the maximum electrical conductivity and revealed a maximum electromotive force for a given oxygen partial pressure. Experimental voltage curve of this oxygen sensor take on a sharper, more steplike transition at the stoichiometric A/F ratio than those of other commercial oxygen sensors.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.6
• /
• pp.359-364
• /
• 2019

The suspension plasma spraying is a modification of conventional plasma spray techniques that has been developed to overcome the challenge of using fine particles in plasma spray processes. In this study, microstructure developments and mechanical property of yttrium oxide (Y₂O₃) coatings prepared by the suspension plasma spray coating technique have been investigated to determine the effect of processing parameters including plasma gun current and total gas flow. The results showed that a highly dense Y₂O₃ coating having low porosity of 0.2 vol% without any lamellar structures can be achieved at the optimum condition of gun current 200 A and total gas flow 220 L/min.

• Korean Journal of Materials Research
• /
• v.11 no.4
• /
• pp.283-289
• /
• 2001

Composite cathodes of 50/50 vol% LSM- YSZ (La$_{1-x}$Sr$_{x}$MnO$_3$-yttria stabilized zirconia) were deposited onto surface- Polished YSZ electrolytes by colloidal deposition technique. The cathode characteristics were then examined by scanning electron microscopy (SEM) and X-ray diffraction (XRD) and studied by ac impedance spectroscopy (IS). The typical impedance spectra measured for an air/LSM- YSZ/YSZ/Pt/air cell at $700^{\circ}C$ were composed of two depressed arcs. Addition of YSZ to the LSM electrode significantly enlarged the triple-phase boundaries (TPB) length inside the electrode, which led to a pronounced decrease in cathodic resistivity of LSM-YSZ composite electrodes. Polishing the electrolyte surface to eliminate the influences of surface impurities and to enlarge the TPB length can further reduce cathode resistivity. The cathodic resistivity of the LSM- YSZ electrodes was a strong function of operation temperature, composition and particle size of cathode materials, applied current, and electrolyte surface roughness.

• Journal of Powder Materials
• /
• v.20 no.6
• /
• pp.445-452
• /
• 2013

Yttria-stabilized zirconia (YSZ) coatings are fabricated via suspension plasma spray (SPS) for thermal barrier applications. Three different suspension sets are prepared by using a planetary mill as well as ball mill in order to examine the effect of starting suspension on the phase evolution and the microstructure of SPS prepared coatings. In the case of planetary-milled commercial YSZ powder, a deposited thick coating turns out to have a dense, vertically-cracked microstructure. In addition, a dense YSZ coating with fully developed phase can be obtained via suspension plasma spray with suspension from planetary-milled mixture of $Y_2O_3$ and $ZrO_2$.

• Journal of Korean Ophthalmic Optics Society
• /
• v.11 no.2
• /
• pp.85-89
• /
• 2006

To research of the improved mechanical properties of materials for spectacle lens cutting, SiC and TiC were used as the main powder. Also, $Al_2O_3$ and $Y_2O_3$ was included as a sintering additive. The weight ratio of the alumina($Al_2O_3$) to yttria($Y_2O_3$) was set to 1:1. The materials for spectacle lens cutting were fabricated by hot-pressing at $1810^{\circ}C$ for 1h and subsequently annealed at $1860^{\circ}C$ for 3, 6 and 12h to initiated grain growth. The longer annealing time is, the bigger the grain size is. The microstructures were observed by scanning electron microscopy (SEM). The SEM images were quantitatively analyzed by image analysis (Image-Pro Plus, Media Cybernetics, Maryland, U.S.A.). Crack deflection by elongated SiC grains was most frequently observed as the dominant toughening mechanism. Crack deflection was generally observed for elongated SiC grains with aspect ratio(AR) > 2.5 and grain thickness < $2.3{\mu}m$. Crack bridging was also observed as one of the operating toughness mechanism.

• Transactions of the Korean hydrogen and new energy society
• /
• v.17 no.2
• /
• pp.204-211
• /
• 2006

The electrolyte in the solid oxide fuel cell must be dense enough to avoid gas leakage and thin enough to reduce the ohmic resistance. In order to manufacture the thin and dense electrolyte layer, 8 mol% $Y_2O_3$ stabilized-$ZrO_2$ (8YSZ) electrolyte layers were coated on the porous tubular substrate by the novel vacuum slurry dip-coating process. The effects of the slurry concentration, presintering temperature, and vacuum pressure on the thickness and the gas permeability of the coated electrolyte layers have been examined in the vacuum slurry coating process. The vacuum-coated electrolyte layers showed very low gas permeabilities and had thin thicknesses. The single cell with the vacuum-coated electrolyte layer indicated a good performance of $495\;mW/cm^2$, 0.7 V at $700^{\circ}C$. The experimental results show that the vacuum dip-coating process is an effective method to fabricate dense thin film on the porous tubular substrate.