• Composites Research
• /
• 제12권2호
• /
• pp.53-61
• /
• 1999

복합재료의 파단식은 강도계수의 산정이 쉽고, 형상이 유연하며, 논리적인 단순성을 유지하기 위하여 각 파단모드와 하중조건을 고려하는 것이 바람직하다. 본 연구에서는 인장 및 비틀림의 이축하중에 대한 등가강도를 도입함으로써 새로운 파단식을 유도하였다. 이축 실험 결과는 등가이축강도가 cos($tan^{-1}R_b$)의 지수함수로 표현됨을 보였다. 이축하중의 파단강도는 일방향 인장강도 및 비틀림강도와 이축비의 함수로 예측할 수 있다. 실험 데이터의 산포성은 Weibull 분포함수와 등가이축강도 개념을 이용하여 분석하였다. 또한, 일방향 인장 및 비틀림 S-N 선도로부터 복합하중하의 S-N 선도를 구할 수 있는 피로해석법을 평면 응력 모델을 기반으로 개발하였다. 예측결과는 적층복합재료의 이축강도와 피로수명의 실험 데이터와 잘 일치하였다.

• 한국정밀공학회지
• /
• 제22권12호
• /
• pp.149-155
• /
• 2005

The rotating components such as turbine rotors in service are generally subjected to multiaxial cyclic loading conditions. The prediction of fatigue lift for turbine rotor components under complex multiaxial loading conditions is very important to prevent the fatigue failures in service. In this paper, axial and torsional low cycle fatigue tests were preformed for 3.5NiCrMo steels serviced low pressure turbine rotor of nuclear power plant. Several methods to predict biaxial fatigue life such as Tresca, von Mises and Brown & Miller's critical plane approach were evaluated to correlate the experimental results for serviced NiCrMoV steel. The fracture mode and fatigue characteristics of NiCrMoV steel were discussed based on the results of fatigue tests performed under the axial and torsional test conditions. In particular, the Brown and Miller's critical plane approach was found to best correlate the experimental data with predictions being within a factor of 2.

• 대한기계학회논문집A
• /
• 제25권10호
• /
• pp.1644-1650
• /
• 2001

Mechanical properties of domestic 374 stainless steel have been evaluated fur membrane material used in LNG storage tank. LNG tank is operated around -162$^{\circ}C$. The temperature of membrane depends on LNG level. Accordingly, the membrane material is deteriorated by variation of liquid pressure and temperature. Tensile test and fatigue life test were performed at room temperature and -l62$^{\circ}C$ per code requirements. Especially the biaxial fatigue life test was conducted with shaped membrane sheet at a thermal strain of $\Delta$T=190$^{\circ}C$ The test results obtained with the domestic 304 stainless steel showed better properties compared to the values required by code.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.206-211
• /
• 2000

Fatigue test was conducted on a S45C steel using hour-glass shaped smooth tubular specimen under biaxial loading in order to investigate the crack formation and growth at room temperature. Three types of loading system, i.e fully reserved cyclic torsion without a superimposed static tension or compression, fully reserved cyclic torsion with a superimposed static tension and fully reserved cyclic torsion with a superimposed static compression were employed. The test results show that a superimposed static tensile mean stress reduced fatigue lifetime. however a superimposed static compressive mean stress increased fatigue lifetime. Experimental results indicated that cracks were initiated on planes of maximum shear strain with either a superimposed mean stresses or not. A biaxial mean stress had an effect on the direction which cracks nucleated and propagated at stage I (mode II).

• 콘크리트학회논문집
• /
• 제16권1호
• /
• pp.27-35
• /
• 2004

지금까지 콘크리트에 대한 피로실험과 연구는 대부분 압축응력, 휨응력을 받는 경우에 대하여 연구를 진행하였으나 실제 교량이나 도로 포장콘크리트 구조물은 이축응력상태의 조합응력을 받게 된다. 따라서, 본 연구에서는 이러한 콘크리트 구조체가 받게 되는 이축응력 상태를 이상적으로 재현할 수 있는 쪼갬인장 피로실험방법을 제안하고 적용성을 평가 하고자 하였다. 실험은 ${\phi}15{\times}30cm$를 사용한 KS 규정을 응용하여 ${\phi}15{\times}7.5cm$의 시편을 제작하고, 쪼갬인장 피로실험에 적용하기 위한 타당성 검증을 수행하였으며, 이상적 탄성재료인 강재와 고체의 비교를 위하여 모르타르 시편을 제작하여 검증실험을 수행하였다. 또한, 이론적 고찰과 유한요소 해석을 수행하여 이론치와 해석치의 비교 고찰하였으며 정적 강도측정 및 게이지 부착실험을 수행하여 타당성을 입증하고자 하였다. 실험결과, FEA결과, 수평응력과 압축응력의 비는 3.1로 나타나 이론치 3.0과 유사한 결과를 얻을 수 있었다. 수평응력은 시편의 길이가 30cm일 경우 이론상 3MPa이지만, 본 연구에서는 시편의 길이가 30cm와 5cm일 때 각각 2.98MPa와 2.96MPa로 나타났다. 쪼갬인장 피로실험방법은 유한요소 해석, 정적 강도측정 및 게이지 부착실험모두에서 충분한 타당성을 나타내었으며, 이 방법은 실제 응력 모사, 실험의 간편성, 현장 시편 이용 가능성 등 많은 장점을 가지고 있는 것으로 판단되어 향후 교량이나 도로포장 구조물에 사용되는 콘크리트의 피로거동을 모사하는데 적합한 실험방법으로 사료된다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 추계학술대회 논문집
• /
• pp.666-671
• /
• 1993

Fatigue life prediction under multi-axial variable load were performed for Aluminium 7075-T651 alloy using SAE Notched specimen & Torque tube shaft component specimen. When variable multiaxial load is applied to material, maximum damaged plane(critical plane) change. To clarify the situation, experiment is performed on two different changing load path. For multiaxial fatigue life prediction, miner rule is expanded to critical plane theory. Shear based parameter and Elliptical parameter give better correlation. This suggests that miner rule can be applicable on multi-axial variable load.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.156-161
• /
• 2004

To predict the direction of the fatigue crack initiated from a hole under various types of biaxial fatigue loads with different phase difference and biaxiality, fatigue parameters were investigated. Axial and torsional biaxial fatigue loads were selected with the respective combination of five different phase differences of 0, 45, 90, 145 and 180 degrees and five biaxialities of 0, $1/{\sqrt{3}}$, 1, ${\sqrt{3}}$, ${\infty}$. Directions of the fatigue crack initiation around the hole were found to approach to the circumferential direction of the specimen with increment of the phase difference for fatigue tests with phase differences less than $90^{\circ}$. Whereas directions for tests with phase differences greater than $90^{\circ}$ went away from the circumferential direction and those were symmetric to the directions for tests with phase difference less than $90^{\circ}$. With increase of biaxilities, the fatigue crack initiated more apart from the circumferential direction of the specimen. These crack initiation direction were predicted using maximum tangential stress range and maximum shear stress range obtained at far-field and around the hole. Comparing these two stress parameters, The crack initiation direction can be successfully explained by using the direction of the maximum tangential stress range obtained around the hole and at far-field.

• 대한기계학회논문집A
• /
• 제27권10호
• /
• pp.1695-1702
• /
• 2003

Fatigue crack initiation around a hole subjected to biaxial fatigue loads with a phase difference was investigated. Axial and torsional biaxial fatigue loads with different phase differences and biaxiality of 1/√3 were applied to thin-walled tubular specimens. Five phase differences of 0, 45, 90, 145 and 180 degrees were selected. Directions of the fatigue crack initiation around the hole were found to approach to the circumferential direction of the specimen with increment of the phase difference for fatigue tests with phase differences less than 90$^{\circ}$. Whereas directions for tests with phase differences greater than 90$^{\circ}$ got away from the circumferential direction and those were symmetric to the directions for tests with phase difference less than 90. . Furthermore, it was shown that the fatigue initiation life decreased with increment of phase difference for fatigue tests with phase differences less than 90$^{\circ}$, but it increased for tests with phase difference greater than 90$^{\circ}$. The crack initiation direction can be successfully explained by using the direction of the maximum tangential stress range obtained around the hole and at far-field.

• 한국해양공학회지
• /
• 제18권6호
• /
• pp.84-90
• /
• 2004

Fatigue tests were conducted on SM45C steel using hour-glass shaped smooth tubular specimen under biaxial loading in order to investigate the crack formation and growth at room temperature. Three types of loading systems, were employed fully-reserved cyclic torsion without a superimposed static tension or compression fully-reserved cyclic torsion with a superimposed static tension and fully-reserved cyclic torsion with a superimposed static compression. The test results showed that a superimposed static tensile mean stress reduced fatigue life however a superimposed static compressive mean stress increased fatigue life. Experimental results indicated that cracks were initiated on planes of maximum shear strain whether or not the mean stresses were superimposed. A biaxial mean stress had an effect on the direction that the cracks nucleated and propagated at stage 1 (mode II).

• 한국기계가공학회지
• /
• 제17권4호
• /
• pp.113-122
• /
• 2018

A hydraulic breaker is an attachment of an excavator, and it crushes stones. Recently, research to reduce the impact and noise of breakers are ongoing. In this paper, a method to improve the upper, lower, and side dampers, which act as insulation for the attenuation of vibration during breaker operation, is studied through testing and simulation. To obtain the nonlinear material constants required for the simulation, the biaxial tensile test was performed with urethane, which is a material used for dampers. The existing parts and the improved parts were compared and evaluated using the LS-DYNA program. As a result, 50% of the equivalent stress was reduced in the bracket body of the hydraulic breaker, and the equivalent stress of the side damper was also decreased. We verified that the fatigue conditions were satisfied by performing a fatigue analysis.