• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.363-367
• /
• 2009

From the recent, an big issue of the internet attack is DDoS(Distributed Denial of Service). Some government agencies and companies will buy Anti-DDoS SW for protect their their network system form DDoS attack. But We don't have any objective valuation standard of Anti-DDoS SW. So When you try to buy an Anti-DDoS SW, you can get only subjective Anti-DDoS SW information which from Anti-DDoS SW vender. Anti-DDoS SW market is getting bigger, so market needs objective valuation standard of Anti-DDoS SW for a fair evaluation. In this paper, we describe a part of Anti-DDoS SW performance tests in valuation standard of Anti-DDoS SW.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.21 no.7
• /
• pp.402-408
• /
• 2009

In this paper, the effects of ventilation and humidification on thermal comfort and indoor air quality(IAQ) were evaluated in a classroom when a heat pump system was operated in winter. Thermal comfort parameters, such as temperature, relative humidity, globe temperature and air velocity, were measured at 9 points in the classroom. The concentration of $CO_2$ and total suspended particles(TSP) in the classroom were measured in order to analyze IAQ. Temperature distribution in the classroom was decreased by $2{\sim}5^{\circ}C$ when the ventilation system and the humidifier were operated. When the relative humidity was adjusted to 60% by operating the humidifier and the ventilation system, the predicted mean vote(PMV) in the classroom was within the comfortable range of $-0.5{\sim}0.5$. When the ventilation system was operated, the average concentration of $CO_2$ and TSP were decreased by 645 ppm and 0.17 $mg/m^3$, respectively. This paper suggests the humidification and ventilation conditions to maintain the comfortable environment in the school classroom in winter experimentally.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.6
• /
• pp.381-387
• /
• 2008

The presence of non-condensable gases as an additional thermal resistance inside a refrigerating circuit has been found for a general refrigerator, The effect of non-condensable gases was varied by controlling the injection amount of dry air into the refrigerating circuit to increase a thermal resistance. Energy consumption tests for the refrigerator were conducted under the various amounts of non-condensable gases. The tested refrigerating circuit was the household refrigerator. As the molar fraction of non-condensable gases was increased from 0% to 1.46%, the amount of energy consumption was found to increase up to 25%. The increase of the amount of non-condensable gases in refrigerating circuit was found to result in increasing the condensation temperature at the condenser and decreasing the evaporation temperature at the evaporator, which were presumably caused by the low specific heat and increased partial pressure of non-condensable gas.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.6
• /
• pp.394-399
• /
• 2008

There are many attempts to use a fuel cell system as a residential power generation system. The purpose of this study is to investigate the optimal design of a water tank for a hot water system when the fuel cell co-generation system is combined with a domestic hot water supply system. The demands of hot water supply per month per home are investigated in Busan for a year. It showed somewhat large differences between the actual demand and the designed demand of hot water, but the actual capacity of hourly averaged hot water demands is analyzed as $60{\ell}/h$ in this study based on the actual demand. The experiments are performed in the various inlet and outlet locations of nozzles, and the hot water consumption rates. The experimental results are showed that the optimal capacity of the water tank is $200{\ell}$ when the thermal efficiency, the storing capacity of hot water and the space for installation are considered.

• Transactions of Materials Processing
• /
• v.28 no.5
• /
• pp.257-265
• /
• 2019

Multi-axial forging (MAF), a severe plastic deformation technique, is known to be difficult to obtain materials with homogeneous microstructures. Recently, multi-axial diagonal forging (MADF) process has been developed to solve this problem. In this study, in order to compare the microstructural and mechanical homogeneities of the MAFed and MADFed samples, oxygen-free copper (OFC) cubes measuring 25 mm in length were deformed through MAF and MADF processes and the average grain size and hardness were measured at the edge, face, and center regions of the samples. In the MAFed samples, ultrafine grains were formed at the center region, but a considerable amount of coarse grains remain at the face region. Therefore, the MAFed samples showed a high inhomogeneity in regards to grain size and hardness. On the contrary, in the case of the MADFed sample, the grain sizes at the edge, face, and center regions were similar and the hardness in all the regions are almost similar. This indicates that the MADFed sample has a homogeneous microstructure and uniform mechanical properties, which can be attributed to the homogeneous distribution of the effective strain throughout the material. The results of this study suggests that the MADF is a suitable process in the fabrication of high-strength copper materials with a homogeneous and ultrafine grain structure.

• Journal of Medicine and Life Science
• /
• v.15 no.2
• /
• pp.108-111
• /
• 2018

Extra-corporeal membrane oxygenation (ECMO) has the potential to rescue patients in cardiac arrest or respiratory failure. ECMO has two systems such as veno-arterial and veno-venous circulation. In cardiac arrest resulting from acute myocardial infarction, veno-arterial ECMO is mandatory for systemic circulation and oxygenation. A 75-year old female patient underwent primary coronary intervention for acute myocardial infarction. Despite successful revascularization, recurrent ventricular tachycardia and heart failure were progressing. We performed a veno-arterial ECMO through the femoral artery and vein, then the patient seemed to be stable clinically. However, laboratory studies, echocardiography, and vital signs indicated multi-organ failure and decreasing cardiac function. We found out an error that we performed veno-venous ECMO instead of veno-arterial ECMO. We added a femoral artery cannula and exchange the circuit system to veno-arterial ECMO. While the systemic circulation seemed to be recovered, the left ventricular function was decreased persistently. A hypovolemia resulting from pulmonary hemorrhage was occurred, which lead to ECMO failure. The patient died of cardiac arrest and multi-organ failure 23 hours after ECMO. Because the color of arterial and venous circuits represent the position and efficacy of ECMO, if unexpected or abnormal circuit colors are detected, prompt and aggressive evaluation for ECMO function is mandatory.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.22 no.4
• /
• pp.492-500
• /
• 2019

Equal channel angular pressing(ECAP) is a severe plastic deformation technique capable of introducing large shear strain in bulk metal materials. However, if an ECAPed material has an inhomogeneous microstructure and anisotropic mechanical properties, this material is difficult to apply as structural components subjected to multi-axial stress during use. In this study, extruded oxygen-free copper(OFC) rods with a large diameter of 42 mm are extruded through ECAP by route Bc up to 12 passes. The variations in the microstructure, hardness, tensile properties, and microstructural and mechanical homogeneity of the ECAPed samples are systematically analyzed. High-strength OFC rods with a homogeneous and equiaxed-ultrafine grain structure are obtained by the repeated application of ECAP up to 8 and 12 passes. ECAPed samples with 4 and 8 passes exhibit much smaller differences in terms of the average grain sizes on the cross-sectional area and the tensile strengths along the axial and circumferential directions, as compared to the samples with 1 and 2 passes. Therefore, it is considered that the OFC materials, which are fabricated via the ECAP process with pass numbers of a multiple of 4, are suitable to be applied as high-strength structural parts used under multi-axial stress conditions.

• Korean Journal of Medicinal Crop Science
• /
• v.28 no.6
• /
• pp.445-454
• /
• 2020

Background: Culturing wild ginseng adventitious root using plant factory technology provides genetic safety and high productivity. This production technology is drawing attention in the fields of functional raw materials and product development. The cultivation method using elicitors is key technology for controlling biomass and increasing secondary metabolites. Methods and Results: Elicitor treatments using methyl jasmonate, pyruvic acid, squalene, β-sistosterol were performed to amplify total ginsenosides (Rb1, Rc, Rb2, Rb3, and Rd) of cultured wild ginseng adventitious root. Thereafter, fermentation and steaming processes were performed to convert total ginsenosides into minor molecular ginsenosides (Rg3, Rk1, and Rg5). The result indicated that methyl jasmonate minimizes the reduction in fresh weight of cultured wild ginseng adventitious root and maximizes total ginsenosides (sum of Rb1, Rc, Rb2, Rb3, and Rd). Ginsenoside conversion results showed a maximum degree of conversion of 131 mg/g. Conclusions: In this study, we demonstrated that the optimal elicitor treatment method increased the content of total ginsenosides, while the steaming and fermentation processing method increased the content of minor ginsenosides.

• Journal of radiological science and technology
• /
• v.45 no.1
• /
• pp.57-67
• /
• 2022

CZT detectors, which are compound semiconductors that have been widely used recently for gamma-ray detection purposes, are difficult to detect neutrons because direct interaction with them does not occur unlike gamma-rays. In this paper, a method of detecting and determining energy levels (fast neutrons and thermal neutrons) of neutrons, in addition of identifying energy and nuclide of gamma-rays, and evaluating gamma dose rates using a CZT semiconductor detector is described. Neutrons may be detected by a secondary photoelectric effect or compton scattering process with a characteristic gamma-ray of 558.6 keV generated by a capture reaction (¹¹³Cd + ¹n → ¹¹⁴Cd + 𝛾) with cadmium (Cd) in the CZT detector. However, in the case of fast neutrons, the probability of capture reaction with cadmium (Cd) is very low, so it must be moderated to thermal neutrons using a moderator and the material and thickness of moderator should be determined in consideration of the portability and detection efficiency of the equipment. Conversely, in the case of thermal neutrons, the detection efficiency decreases due to shielding effect of moderator itself, so additional CZT detector that do not contain moderator must be configured. The CZT detector that does not contain moderator can be used to evaluate energy, nuclide, and gamma dose-rate for gamma-rays. The technology proposed in this paper provides a method for detecting both neutrons and gamma-rays using a CZT detector.

• Journal of radiological science and technology
• /
• v.47 no.3
• /
• pp.183-195
• /
• 2024

Additional functional upgrades to the large-area compton camera (LACC) measurement device that can provide characteristics evaluation information (nuclear species and radioactivity) and two-dimensional or three-dimensional distribution imaging information of radioactive materials existing in surface or internal of concrete structures are required in terms of work stability and efficiency in order to apply to actual decommissioning sites such as nuclear power plants or medical cyclotron facilities by using this measurement device. To this purpose, the technology that allows radiation workers to intuitively and visually check the distribution of radioactive materials in advance by matching the two-dimensional distribution imaging information of radioactive materials obtained through the LACC measurement device and visual imaging of the measurement zone (10 m × 5 m) was developed. In addition, the separate system that can automatically adjust the position (height) in units of the measurement area size (0.7 m × 0.3 m × 0.8 m) of the LACC measurement device was developed and the integrated management system for characteristics evaluation information and two-dimensional or three-dimensional distribution imaging information obtained per unit of measurement for radioactive materials was developed. These functional upgrades related to LACC measurement device can improve work efficiency and safety when measuring radioactivity of concrete structures and enable the establishment of appropriate decommissioning strategies using radioactivity measurement information for decommissioning nuclear power plants or medical cyclotron facilities.