• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1995.11a
• /
• pp.49-55
• /
• 1995

이원 액체추진제를 사용하는 인공위성용 로켓 추진기관의 개발을 위한 핵심부품별 개념 및 상세설계, 성능해석, 성능실험용 시작품의 제작, 수류 성능실험 및 지상 연소시험이 수행되었다. 인공위성 궤도조종용 로켓 추진기관은 1.38MPa의 연소실 압력으로 4초동안 1780N(400$Ib_f$)의 평균추력을 내도록 설계되었으며, 산화제로는 질산, 연료로는 트리 에틸렌 아민(triethylene amine, TEA)과 자이리딘(xylidine)의 혼합물로 구성된 접촉발화형 이원 액체추진제를 사용하고, 추진제를 가압방식에 의해 연소실에 분사하는 방법으로 분사충돌, 미립화, 그리고 기화 후 연소시키게 된다. 효율적인 설계를 위하여 설계전용 소프트웨어를 개발하였으며, 추진기관의 핵심부품별로 유동 시뮬레이션을 수행하고, 해석결과와 수류 실험결과를 바탕으로 설계를 수정, 보완하였다. 지상 연소시험 및 수류 성능실험을 위하여 추진제 공급장치 및 계측 시스템이 설계, 제작되었고, 시스템의 작동 및 자료처리를 위한 소프트웨어를 개발하여 수류 성능실험 및 지상 연소시험에 사용하였으며, 연소시험결과 지상 평균추력 378$Ib_f$를 발생하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.260-263
• /
• 2005

The effects of internal manifold designs the reactant feed-stream in Polymer Electrolyte Fuel Cells (PEFCs) is studied to figure out mass flow-distribution patterns over an entire fuel cell stack domain. Reactants flows are modeled either laminar or turbulent depending on regions and the open channels in the bipolar plates are simulated by porous media where permeability should be pre-determined for computational analysis. In this work, numerical models for reactant feed-stream in the PEFC manifolds are classified into two major flow patterns: Z-shape and U-shape. Several types of manifold geometries are analyzed to find the optimal manifold configurations. The effect of heat generation in PEFC on the flow distribution is also investigated applying a simplified heat transfer model in the stack level (i.e. multi-cell electrochemical power-generation unit). This modeling technique is well suited for many large scale problems and this scheme can be used not only to account for the manifold flow pattern but also to obtain information on the optimal design and operation of a PEMC system.

• New & Renewable Energy
• /
• v.1 no.2 s.2
• /
• pp.41-52
• /
• 2005

The effects of internal manifold designs on the reactants feed-stream in Polymer Electrolyte Fuel Cells [PEFCs] is studied to figure out flow and thermal distribution patterns over an entire fuel cell stack. Reactants flows are modeled either laminar of turbulent depending on regions and the open channels in the bipolar plates are simulated by porous media where permeability should be pre-deter-mined for computational analysis. In this work, numerical models for reactants feed-stream In the PEFC manifolds are classified Into two major flow patterns: Z-shape and U-shape. Several types of manifold geometries are analyzed to find the optimal manifold configurations. The effect of heat generation in PEFC on the flow distribution is also Investigated applying a simplified heat transfer model in the stack level (i.e. multi-cell electrochemical power-generation unit). This modeling technique Is well suited for many large scale problems and this scheme can be used not only to account for the manifold flow pattern but also to obtain Information on the optimal design and operation of PEFC systems.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.2
• /
• pp.150-157
• /
• 2008

The main objective of this paper is to investigate the performance characteristics of a $CO_2$ air conditioning system for fuel cell electric vehicles (FCEV). The present air conditioning system for FCEV uses the electrically driven compressor and electrically controlled expansion valve for $CO_2$ as a working fluid. The experimental work has been done with various operating conditions, which are quite matching the actual vehicle's driving conditions such as different compressor speed and high pressure to identify the characteristics of the system. Experimental results show that the cooling capacity and coefficient of performance (COP) were up to 6.3kW and 2.5, respectively. This paper also deals with the development of optimum high pressure control algorithm for the transcritical $CO_2$ cycle to achieve the maximum COP.

• Transactions of the Korean hydrogen and new energy society
• /
• v.15 no.1
• /
• pp.1-11
• /
• 2004

Hybrid power systems with fuel cells and batteries have the potential to improve the operation efficiency and dynamic response. A proper load management strategy is important to better system efficiency and endurance in hybrid systems. In this paper, a fuzzy logic algorithm has been used to determine the fuel cell output power depending on the external required power and the battery state of charge(SoC). If the required power of the hybrid system is small and the SoC is small, then the greater part of the fuel cell power is used to charge the battery pack. If the required power is relatively big and the SoC is big, then fuel cell and battery are concurrently used to supply the required power. These IF-THEN operation rules are implemented by fuzzy logic for the energy management system of hybrid system. The strategy is evaluated by simulation. The results show that fuzzy logic can be effectively used to optimize the operational efficiency of hybrid system and to maintain the battery SoC properly.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.12
• /
• pp.1022-1030
• /
• 2009

Numerical analysis was carried out to investigate the effect of GDL (Gas diffusion layer) porosity on the performance of PEMFC (proton exchange membrane fuel cell). A complete three-dimensional model was chosen for single straight channel geometry including cooling channel. Main emphasis is placed on the heat and mass transfer through the GDL with different porosity. The present numerical results show that at high current densities, the cell voltage is influenced by the GDL porosity while the cell performance is nearly the same at low current densities. At high current densities, low value of GDL porosity results in decrease of the fuel cell performance since the diffusion of reactant gas through GDL becomes slow with decreasing porosity. On the other hand, for high GDL porosity, the effective thermal conductivity becomes low and the heat generated in the cell is not removed rapidly. This causes the temperature of fuel cell to increase and gives rise to dehydration of the membrane, and ultimately increase of the ohmic loss.

• Journal of the Society of Naval Architects of Korea
• /
• v.52 no.6
• /
• pp.419-427
• /
• 2015

Recently Energy Saving Device has been developed actively due to the regulation of the EEDI. This Energy Saving Device which is newly developed is integrated duct and stator. This paper verified performance of the Energy Saving Device through CFD. The experimentation to find the best pitch angle of each blade of the stator designed has been conducted. The angle of incidence of the duct has been obtained through the measurement of the wake. The experimentation has been carried out with and without Energy Saving Device. The efficiency increase was through these two experiments.

• Transactions of the Korean hydrogen and new energy society
• /
• v.18 no.1
• /
• pp.60-66
• /
• 2007

In terms of the vehicle efficiency, a fuel cell hybrid system has advantages compared to a conventional internal combustion engine and a fuel cell alone-powered system. The efficiency of the fuel cell hybrid vehicle mainly depends on the maximum power of the fuel cell and therefore it is important to decide the design value of the fuel cell maximum power. In this paper, to estimate the performance of the fuel cell hybrid mini-bus in the design phase the simulator based on the models for the fuel cell stack, the electric battery, the fuel cell balance of plant, the controller, and the vehicle itself is proposed. Additionally, the hybrid mini-bus efficiencies with several different fuel cell powers are simulated for a city driving schedule and are compared on another. Consequently, the proposed simulation scheme is useful to determine the best design value of the fuel cell hybrid vehicles.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.643-646
• /
• 2017

In a liquid rocket engine using hydrocarbon fuels, cooling of the combustion chamber wall is necessary to prevent the combustion chamber wall from melting or structurally deforming due to high heat flux. Among the various methods, regenerative cooling, which uses fuel as a coolant and then injects it into the combustion process, has good performance. This study investigated the heat transfer characteristics of kerosene as a coolant by varying the copper cross-sectional area, the flow rate in the channel, and the current applied to the channel. Convective heat transfer occurred rapidly when the cross-sectional area of the copper channel was small and when the kerosene flow velocity was fast.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.424-428
• /
• 2012

Air-breathing Propulsion System is one of the promising propulsion systems because of low cost, easy storage, compactness and simplicity. A study of gas generator propellant for air-breathing propulsion system was performed in this paper. Amorphous Boron Powder was applied in propellant with various kinds of additives to determine combustion characteristics. And boron beads were made to apply them to the propellant. Combustion characteristics of propellant using amorphous boron powder and boron beads was compared.