• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.3
• /
• pp.492-500
• /
• 2011

The airborne backbone network(ABN) provides communication transport services between airborne nodes, surface nodes and satellite nodes. Such ABN is generally constructed with wide-body and high-capacity planes such as AWACS, which can fly long-term along pre-defined flight paths. In this paper, we propose an efficient method to improve routing performances by reconfiguring routing path before link failure based on the prediction of link state with the information of pre-defined backbone nodes' trajectories. Since the proposed method does not need additional information exchange between airborne nodes in order to acknowledge the link failure, it can be effectively used for airborne backbone network with limited bandwidths.

• Journal of Advanced Marine Engineering and Technology
• /
• v.25 no.4
• /
• pp.797-808
• /
• 2001

Three-dimensional trajectory of fluid particle is simulated by a particle motion, which is able to examine the influences of changes in the several parameters. To calculate the trajectory of a particle, the Runge-Kutta method was utilized. The use of a projectile of particles for the trajectory of liquid jet has been shown to be useful to estimate the influence of different operating parameters such as best particle diameter, density of liquid body, initial take-off velocity, wind velocity, cross wind velocity, take-off angle, and base angle for a released flow from the nozzle. The results give the trajectories of various types of particle of body and at different elevations, base angles, wind velocities and densities of liquid body. The trajectories in a vacuum show that air resistances decreases both the distance and the maximum height of a projectile, and also explain that the termination time is also reduced in air. In addition, the maximum distance in the x direction was obtained with take-off angles from 30 degrees to 45 degrees in still air and the projectile of particles was highly effected by wind and cross wind. Clearly, a particle has to be so positioned as to take the optimum possible advantage of the wind if the maximum distances is requested. The wind astern increased the maximum distances of x direction compared with the wind ahead. Finally, it is possible to optimize the design of pump by using these results.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.2
• /
• pp.81-86
• /
• 2013

This paper presents the lane change system for collision avoidance. The proposed algorithm for the collision avoidance consists of path generation and path following. Using a calculated TTC (Time to Collision), partial braking is operated and collision avoidance path is generated considering relative distance, velocity and acceleration. Based on the collision avoidance path, desired yaw angle and yaw rate are calculated for the automated path following. The lateral controller is designed by a Lyapunov function approach using 3 D.O.F vehicle model and vehicle parameters. The required steering angle is determined from wheel velocity, longitudinal and lateral velocity in order to follow the desired yaw angle and yaw rate. This system is developed MATLAB/Simulink and its performance is evaluated using the commercial software CarSim.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2012.10a
• /
• pp.261-262
• /
• 2012

In this research, intelligent protection system for laser boat is introduced. The function of system is to measure the distance and velocity of object from our boat and generate control signals to avoid collision with moving targets. A novel approach to estimate object's position from our ship is tackled on this paper. To do this laser sensors are used to measure distance from ship to targets. The ship position and velocity is estimated by th Kalman filter algorithm. In the real phase, the filtering method will be applied to process signal gathered by laser sensors. Simulation to estimate ship's position and velocity under noise are executed and the results are introduced to show the effectiveness of the algorithm.

• International Journal of Highway Engineering
• /
• v.15 no.6
• /
• pp.135-141
• /
• 2013

PURPOSES : The lack of details of design guideline for zig-zag shaped section approaching central bus stop leads an traffic accident proneness. So, this study analysed the geometric elements of central bus stop area in terms of vehicle dynamics and suggested design alternatives. METHODS : The study analysed a dynamic behaviour of bus moving in and out of zig-zag shaped section using Auto-Turn under scenarios. Based upon dynamic analysis, the study found out the width of overtaking lane is the most influential factor for a safe moving at zig-zag alignment. RESULTS : The width of overtaking lane at design speed of 40, 50, and 60 km/h respectively was suggested given taper ratio of 1 to 10 required for Bus Rapid Transit (BRT), and the lane width is not wider than 4.0m which possibly makes two vehicles using the same lane. Also, the width of overtaking lane which mitigates the taper ratio was suggested with the same restriction about the maximum lane width. CONCLUSIONS : The results of the study can be used to prepare a design guideline on zig-zag shaped alignment of central bus exclusive lanes. The more stable moving is expected by applying the design alternatives suggested, therefore the lower rate of traffic crashes at the vicinity of central bus stops.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.429-434
• /
• 2012

Ignition delay of micro/nano aluminum particles is caused by aluminum oxide shell. The method of minimizing this ignition delay is proposed in the study. Generating and heating of particles are processed at the same time. As soon as heated particles are produced, they immediately contact with oxygen. Chemical reaction is induced on the contact surface instead of crystallization of oxide shell. Finally particles are ignited. Aluminum particles are generated by laser ablation on an aluminum plate using Nd:YAG pulse laser. Injected particles are confirmed through visualization of particles using scattering method. $CO_2$ continuous laser supplies heat to aluminum plate and generated particles. Trace of burning particles is observed in the experiment.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2004.05a
• /
• pp.481-484
• /
• 2004

이 논문에서는 소포 배달 서비스를 위한 인텔리전트 모니터링 시스템(Intelligent Monitoring and Control System; IMCS)에 대해 기술한다. IMCS 는 GIS, GPS 그리고 무선 통신 기술을 이용하여 택배의 접수와 배달 업무를 효율적이고 효과적으로 개발하기 위한 시스템이다. IMCS는 모두 세개의 서브 시스템으로 구성되어 있는데 접수와 배달 계획을 수립하는 PDPS(Pick-up and Delivery Planning System)과 접수/배달 현황과 차량의 위치를 파악할 수 있는 PDMS(Pick-up and Delivery Monitoring System), 그리고 개인휴대단말기(PDA)을 이용한 실시간 업무 처리 시스템인 MOCS(Mobile Operations and Communication System)으로 구성되어 있다. PDPS는 GIS와 최적화 알고리즘을 이용하여 접수와 배달을 위한 방문 순서와 경로 그리고 고객에게 방문할 예정시간 등을 생성한다. MOCS에서는 GPS와 무선 통신을 이용하여 업무 중 발생한 접수/배달 결과와 위치 정보를 실시간으로 PDMS에 전송하고 바코드 스캐닝과 전자 서명 등의 업무를 지원한다. PDMS에서는 수신한 정보에 따라 소포의 접수/배달 현황과 차량의 위치를 전자지도 상에 표현하고 업무 차량의 이동 궤적을 표시하여 계획된 경로와 비교하여 모니터링하고 관제할 수 있다. 현재 IMCS는 국내 한 우체국에서 시범 운영되고 있다.

• Journal of Korea Game Society
• /
• v.20 no.6
• /
• pp.63-74
• /
• 2020

Recently, research on automating game tests using artificial intelligence agents instead of humans is attracting attention. This paper aims to collect play data from human and artificial intelligence and analyze their similarity as a preliminary study for game balancing automation. At this time, constraints were added at the learning stage in order to create artificial intelligence that can play similar to humans. Play datas obtained 14 people and 60 artificial intelligence by playing Flippy bird games 10 times each. The collected datas compared and analyzed for movement trajectory, action position, and dead position using the cosine similarity method. As a result of the analysis, an artificial intelligence agent with a similarity of 0.9 or more with humans was found.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.9
• /
• pp.639-646
• /
• 2022

Landing site searching algorithms are developed for a quadrotor using a depth map in unknown environment. Guidance and control system of Unmanned Aerial Vehicle (UAV) consists of a trajectory planner, a position and an attitude controller. Landing site is selected based on the information of the depth map which is acquired by a stereo vision sensor attached on the gimbal system pointing downwards. Flatness information is obtained by the maximum depth difference of a predefined depth map region, and the distance from the UAV is also considered. This study proposes three landing methods and compares their performance using various indices such as UAV travel distance, map accuracy, obstacle response time etc.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2011.11a
• /
• pp.1027-1030
• /
• 2011

휴머노이드 로봇 중 초상화를 그리는 로봇이 있지만 다양한 영상을 입력받아 명암 및 그림자까지 그림을 그리는 로봇은 흔하지 않다. 기존의 화가로봇들은 사용자의 얼굴을 영상으로 입력받아 윤곽선만 추출하여 그리는 방식으로, 입력된 영상으로부터 로봇 암을 제어하는 과정에서 제대로 동기화가 이뤄지지 못해 드로잉 속도가 느리고 원본 영상과 비교 시 차이가 많이 난다. 본 연구에서는 입력된 영상으로부터 명암과 그림자를 인식하여 표현해 줌으로써 입체감 있는 그림의 드로잉이 가능하다. 또한, 로봇 암의 미세한 컨트롤을 통해 드로잉 선 두께를 제어함으로써 자연스러운 그림을 그리고, 드로잉 속도가 향상되어 정확도를 높일 수 있게 하는 휴리스틱 암 제어 기술을 제안한다. 이를 구현하기 위해서는 영상으로부터 명암, 그림자의 농도에 따라 레벨을 결정하고, 레벨을 바탕으로 주변 명암 픽셀들을 평활화 하여 좌표 집합을 추출한다. 좌표 값들로 부터 유효 궤적을 분석하여 로봇 암이 이동할 경로를 추출하고, 효율적인 드로잉 기법을 통해 명암을 표현하여 드로잉하려 한다.