• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.5
• /
• pp.572-578
• /
• 1985

A composite gear with involute-circular are tooth profile and a tooth profile of the rack to cut this gear are theoretictically obtained. The composite gear has involute tooth profile in the vicinity of pitch point and has circular arc tooth profiles at addendum adn dedendum. The contact ratio(M$_{c}$), chordal tooth thickness (chordal tip tooth thickness S$_{t}$, chordal root tooth thickness S$_{t}$) of the composite gear are compared with those of involute gear. When module, number of teeth and pressure angle eqaul, S$_{t}$ of composite gear is much larger than that of involute gear. Under the same conditions, S/sib t/ and M$_{c}$ of composite gear become smaller than those of involute gear.lute gear.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.4
• /
• pp.463-473
• /
• 2011

The warm shrink fitting process is generally used to assemble automobile transmission parts (shaft/gear). But the fitting process can cause the dimensions of addendum and dedendum of the gear to change with respect to the fitting interference and the profile of the gear. As a result, there may be additional noise and vibration between gears. To address these problems, we analyzed the warm shrink fitting process according to process parameters; the fitting interference between the outer diameter of the shaft and the inner diameter of the gear, the inner diameter of the gear, addendum and dedendum of the gear, the heating temperature. In this study, a closed form equation for predicting the amount of deformation of addendum and dedendum in the R-direction was proposed. And the FEA method to analyze the cooling process was proposed for thermal-structural-thermal coupled field analysis of the warm shrink fitting process (heating-fitting-cooling process).

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.5
• /
• pp.34-42
• /
• 2008

• Transactions of The Korea Fluid Power Systems Society
• /
• v.2 no.4
• /
• pp.23-29
• /
• 2005

In order to improve the efficiency of hydraulic gear pumps or motors especially for high operating pressure, power losses due to viscous friction and leak flow through gear teeth end-gaps are considered in this paper. Optimal gaps minimizing the power loss for pumps and motors with uniform heights of gaps are analysed first. And the effect of the shapes of gaps with unequal heights on the power loss are studied and discussed by simulation. Considering that the outer shell lacing gear teeth may expand due to high internal pressure or thermal stress, the results drawn in this paper can be used for the design of high efficiency pumps and motors.

• Tribology and Lubricants
• /
• v.9 no.2
• /
• pp.1-8
• /
• 1993

기어가 비교적 큰 하중과 고속의 운전상태에서 사용되는 경우 되풀이 응력에 의한 피로를 대상으로 하는 면압이나 굽힘강도 이외에 치면에서 발생되는 긁힘이나 융착(瀜着) 또는 용착(溶着)을 대상으로 한 스코어링(scoring) 강도를 고려하여야 한다. 스코어링은 주로 치의 이끝 부분에서 접촉방향으로 긁힘이 나타나는 손상으로 특징지워진다. 미국기어제조협회(AGMA)에서는 윤활막 파손에 의한 금속과 금속과의 접촉에 기인하여 발생되는 여러형태의 손상, 예를 들면 scuffing, seizing, galling 등을 광범위하게 스코어링으로 통칭하고 있다. 미국계통의 기술분야에서는 스코어링을 고온 스코어링(hot scoring)과 저온 스코어링(cold scoring)으로 구분하고 있다. 고온 스코어링은 고속 운전시 표면의 섬광온도(flash temperature)에 기인한 용착과 접촉방향으로 재료를 이탈시키는 형태를 나타내고, 저온 스코어링은 저속의 기어에서 윤활막 파단으로 표면에 줄질(filing)한 듯한 손상이 발생되는 것을 나타낸다. 유럽에서는 고온 스코어링 손상은 스커핑이라 하고 저온 스코어링손상만을 스코어링이라 부르고 있다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.803-806
• /
• 1995

The vibration and nosic of gears is causeed by manufacting error,alignment error in assembly, and thr meshing stiffness of gears which changes periodically as the meshing of teeth process. On a pair of power transmission helical gears with profile error, the relation between the characteristics of gear vibration and the profile error type have been investigated by simulating the vibrational acceleration level and calculating the natural frequency. The results show that the profile error decrease the natural frequency by reducing the tool stiffness and that the concave error type increase the vibrationsl level. And this paper describes the effect of the tip relief on the vibrational acceleration level which a pair of helical gears with concave error generates.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.2
• /
• pp.223-230
• /
• 2003

Stress patterns are created in the plastic spur gear tooth body by introducing a hole or a steel pin to improve stress distribution. Static analysis using finite element method is carried out to show the effect. The result shows that maximum stress as well as tooth tip displacement is dependent on the size and location of a hole or a steel pin. When a hole located on the tooth center line, the maximum static stress level and the tooth tip deflection is always higher than that of a solid gear. But, a considerable reduction in the maximum stress and tooth tip displacement is achieved by insertion of steel pin.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.6
• /
• pp.870-875
• /
• 1986

In this study, full-rounded tip curve of rack and its mating fillet curve of pinion in Involute-circular arc composite tooth profile are derived. Mechanical characteristics are calculated analytically, i.e., Specific sliding, Nominal bending stress at working root circle and the Contact factor of the arc of contact in circular arc part to the arc of double contact. These characteristics compared with standard involute tooth profile are improved in circular arc part of composite tooth profile. To obtain more efficient composite tooth profile, we studied these characteristics with regard to the changes of unwound angle and radius of circualr arc. And a design method of composite tooth profile is suggested. Composite tooth profile are compared with standard involute tooth profile.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.312-315
• /
• 2002

This paper summarizes the results of a numerical study conducted to analyze the effect of selected process parameters on material flow and thread profile in thread rolling of large diameter blanks. Based on the previous work where a plane strain mode was found to provide a reasonable approximation of the thread rolling process, the effect of varying thread form, friction factor, flow stress, and blank diameter on effective strain and thread height was analyzed using the finite element code DEFORM. This study show that effective strain for flank angle, that blank diameter had important effect on the as-rolled thread while flow stress, friction factor, and crest round of dies had significant impact on effective strain at the thread root and crest and load of thread rolling. While the rate of strain harding was found to have an effect on the crest profile, the results indicate that it is the primary factor responsible for seam formation in rolled threads.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.8
• /
• pp.1029-1033
• /
• 2013

Elliptical gear is used as a rotor of oval flowmeter. The elliptical gear can assist water flow-rate measurement by the space of the elliptical shape. Presently, elliptical gears have been processed using hob tool imported from Japan. But if it were not for the technical cooperation with Japan company, the Elliptical gears can't be processed. The purpose of this study is developing a domestic technology for elliptical gears and overcoming the dependence of foreign technical skills. It will bring the import substitution effect. In case of pressure angle $20^{\circ}$, the elliptical gears have an interference of tooth. The increase of pressure angle makes the root of a tooth thick and the top of tooth thin. By results of this study, tooth of elliptical gear was designed and verified through the 2D and 3D simulation.