• Journal of Korean Society on Water Environment
• /
• v.36 no.3
• /
• pp.185-193
• /
• 2020

Bimodal flocculation describes the aggregation and breakage processes of the flocculi (or primary particles) and the flocs in the water environment. Bimodal flocculation causes bimodal size distribution with the two separate peaks of the flocculi and the flocs. Extracellular polymeric substances and ionic species common in the water environment increase the occurrence of bimodal flocculation and flocculi-floc size distribution, under the flocculation mechanisms of electrostatic attraction and polymeric bridging. This study investigated bimodal flocculation and flocculi-floc size distribution, with respect to the extracellular polymeric substance concentration and ionic strength in the kaolinite-containing suspension. The batch flocculation tests comprising 0.12 g/L of kaolinite showed that the highest flocculation potential occurred at the lowest xanthan gum (as extracellular polymeric substances) concentration, under all the ionic strengths of 0.001, 0.01, and 0.1 M NaCl. Also, it was important to note that the higher ionic strength resulted in the higher flocculation potential, at all the xanthan gum concentrations. The bimodal flocculation and flocculi-floc size distribution became apparent in the experimental conditions, which had low and intermediate flocculation potential. Besides the polymeric bridging flocculation, steric stabilization increased the flocculi mass fraction against the floc mass fraction, thereby developing the bimodal size distribution.

• Journal of Korean Society of Water and Wastewater
• /
• v.20 no.2
• /
• pp.245-255
• /
• 2006

Dissolved air flotation is a solid-liquid separation system that uses fine bubbles rising from bottom to remove particles in water. In order to enhance the flotation velocity and removal efficiency of flocs in the flotation process, we tried to obtain pretreatment conditions for the optimum DAF process operation by comparing and evaluating features of actual floc formation and flotation velocity etc, according to coagulant types and conditions for flocculation mixing intensity by using PIA, PDA, and FSA. Accordingly, generating big flocs that have low density at low flocculation mixing intensity may reduce treatment efficiency. In addition, generating small flocs at high flocculation mixing intensity makes floc-bubbles smaller, which reduces flotation velocity, In this study, it was found that high flocculation mixing intensity could not remove the remaining micro-particles after flocculation, which had negative effects on treated water quality, Therefore, in order to enhance treatment efficiency in a flotation process, flocculation mixing intensity around $50sec^{-1}$ is effective.

• Restorative Dentistry and Endodontics
• /
• v.33 no.2
• /
• pp.125-132
• /
• 2008

The purpose of this study is to compare the shear bond strength of repaired composite resin with different bonding agents and evaluate the effect of bonding agents on composite repair strength. Forty composite specimens (Z-250) were prepared and aged for 1 week by thermo cycling between 5 and $55^{\circ}C$ with a dwell time of 30s. After air abrasion with $50\;{\mu}m$ aluminum oxide, following different bonding agents were applied (n = 10); SB group: Scotchbond multipurpose adhesive (3 step Total-Etch system); XE group: Clearfil SE bond (2 step Self-Etch system); XP group: XP bond (2 step Total-Etch system); XE group: Xeno III (1 step Self-Etch system). After bonding procedure was completed, new composite resin (Z-250) was applied to the mold and cured. For control group. 10 specimens were prepared. Seven days after repair, shear bond strength was measured. Data was statistically analyzed using one-way ANOVA and Tukey's test (p<0.05). The means and standard deviations of shear bond strength (MPa ${\pm}$ S.D.) per group were as follows: SB group: 17.06; SE group: 19.10; XP group: 14.44; XE group: 13.57; Control Group: 19.40. No significant difference found in each group. Within the limit of this study, it was concluded that the different type of bonding system was not affect on the shear bond strength of repaired composite resin.

• Elastomers and Composites
• /
• v.34 no.1
• /
• pp.31-44
• /
• 1999

Interfacial adhesive strength between the fully-crosslinked and partially-crosslinked rubber layers were Investigated at the temperature range of $30{\sim}120^{\circ}C$ for four different rubbers(NR, SBR, EPDM, BIMS). The surfaces of interfacial failure were also investigated using a scanning electron microscopy(SEM). The physical interlinking played a major role in the adhesive strength between the fully-crosslinked rubber layers. When a partially-crosslinked rubber layer was bonded to the fully-crosslinked one, the chemical as well as the physical interlinking affected the adhesive strength. NR showed a "interfacial knotty tearing" pattern, while EPDM showed a typical "cross-hatched" one when the adhesive strength approached to the cohesive tear strength of each material.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2020.06a
• /
• pp.50-50
• /
• 2020

하천, 강어귀 및 해안 지역의 점착성 유사는 흐름 내에 입자의 충돌에 의한 흡탈착으로 인해 다양한 크기의 플록을 형성한다. 이 플록은 오염물과도 군집을 형성하여 하상이 퇴적되는 경우가 많으며 홍수 등과 같은 외부 충격으로 인해 재부 되어 하천 환경 및 생태계에 악영향을 미친다. 군집의 형성은 화학적인 결합과 물리적인 응집으로 분류할 수 있는데, 미세 점착성 유사의 군집형성에 대한 연구는 주로 화학적인 결합에 대한 연구가 활발하다. 반대로 물리적인 결합 혹은 외부 충격에 대한 플록형성 매커니즘에 대한 연구는 미비한 실정이다. 따라서, 본 연구에서는 교반기를 활용한 실험을 통하여 점착성 유사에 대한 물리적인 흡탈착 과정을 분석하였다. 유입된 점착성 유사를 교반기로 외부충격을 주어 흡착과 탈착하는 정도를 탁도와 농도를 통해 정량화하였다. 실험은 원통 수조에서 수행되었으며, 교반기의 RPM을 조절하면서 외부충격의 강도를 조절하였다. 초기 실험을 통해 탁도-농도의 관계를 제시하였고 이를 활용하여 교반강도와 점착성 유사의 농도를 분석하였다. 실험 결과 교반강도가 증가할수록 플록 형성이 활발하게 진행되었으나, 일정 교반강도 이상에서는 다른 흡착 과정을 보였다. 이를 토대로 점착성 유사의 흡탈착의 임계값을 제시하였다. 향후 본 연구결과와 유속 혹은 난류강도 등의 하천특성과 연관성을 분석한다면 하천 내 오염물 관리에 효과적으로 사용될 것으로 기대된다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.32 no.4
• /
• pp.233-240
• /
• 2019

Open-hole tensile tests are usually performed to measure the tensile strengths of composites as they are an essential parameter for designing composite structures. However, correctly modeling the tensile test is extremely challenging as it involves various damages such as fiber and matrix damage, delamination, and debonding damage between the fiber and matrix. Therefore, a progressive damage model was developed in this study to estimate the in-plane failure and delamination between the fiber and matrix. The Hashin damage model and cohesive zone approach were used to model ply and delamination failures. The results of the present model were compared with previously published experimental and numerical findings. It was observed that neglecting delamination during finite element analysis led to overestimation of tensile strength.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.24 no.3
• /
• pp.231-242
• /
• 2008

Purpose: The purpose of this study was to investigate the bond strength of the core-veneer interface in all ceramic systems. Material and Methods: The all ceramic systems tested with their respective veneer were IPS Empress 2 with IPS Eris, IPS e.max Press with IPS e.max Ceram and IPS-e.max ZirCAD with IPS e.max Ceram. Cores (N=36, N=12/group, diameter: 10mm, thickness: 3mm) were fabricated according to the manufacturer's instruction and cleaned with ultrasonic cleaner. The veneer(diameter: 3mm, thickness: 2mm) were condensed in stainless steel mold and fired on to the core materials. After firing, they were again ultrasonically cleaned and embedded in acrylic resin. The specimens were stored in distilled water at $37^{\circ}C$ for 1 week. The specimens were placed in a mounting jig and subjected to shear force in a universal testing machine(Z020, Zwick, Germany). Load was applied at close to the core-veneer interface as possible with crosshead speed of 1.00mm/min until failure. Average shear bond strengths(MPa) were analyzed with a one-way analysis of variance and the Tukey test(${\alpha}=.05$). The failed specimens were examinated by scanning electron microscopy(JSM-6360, JEOL, Japan). The pattern of failure was classified as cohesive in core, cohesive in veneer, mixed or adhesive. Results: The mean shear bond strength($MPa{\pm}SD$) were IPS e.max Press $32.85{\pm}6.75MPa$, IPS Empress 2 $29.30{\pm}6.51MPa$, IPS e.max ZirCAD $28.10{\pm}4.28MPa$. IPS Empress 2, IPS e.max Press, IPS e.max ZirCAD were not significantly different from each others. Scanning electron microscopy examination revealed that adhesive failure did not occur in any all ceramic systems. IPS Empress 2 and IPS e.max Press exhibited cohesive failure in both the core and the veneer. IPS e.max ZirCAD exhibited cohesive failure in veneer and mixed failure.

• Korean Journal of Food Science and Technology
• /
• v.27 no.1
• /
• pp.1-5
• /
• 1995

The texture profile of frankfurter sausages was carried out by comparing the domestic(A) and imported(B) products. Fourteen character notes were identified: elasticity, surface moisture, surface smoothness, center hardness, skin toughness, cohesiveness, denseness, chewiness, moisture release, cohesiveness of mass, lumpiness, graininess, skin separation, and oiliness. Reference scales and the $0{\sim}3$ point numerical scaling method were also established. Panelists evaluated sausage A harder than the sausage B. It had higher skin separation and elasticity scores requring more chewing. Sausage B had lower surface moisture and cohesiveness of mass, but higher moisture release and graininess. Panelists commented that the sausage B were oilier but had milder tastes.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.27 no.5
• /
• pp.495-500
• /
• 1994

Mackerel water-soluble protein solution Mackerel meat washing water were concentrated by isoelectric point shifting precipitation process, and the concentrates were utilized as a material for processing of an elastic gel food such as kamaboko. The water-soluble proteins were partly polymerized during the isoelectric point shifting precipitation process. Then, the water soluble protein concentrates were partly substituted for frozen minced Alaska pollack meat in processing of a good quality kamaboko. The maximum substitution percentage for good quality kamaboko manufacturing was concluded to be below $30\%$, according to the criteria of color difference, jelly strength and folding tests using the substituted recovered protein concentrates.

• Magazine of the Korea Concrete Institute
• /
• v.4 no.2
• /
• pp.119-126
• /
• 1992

고강도 시멘트 복합체의 유동성 손실을 감소시키기 위한 연구의 일환으로 시멘트계 입자에 대한 고성능감수제의 흡착특성, 현탄액 속에서의 응집특성을 관찰하여 시멘트풀과 모르터의 유동성과 관련시켜 고찰하였다. 본 연구결과 알루미네이트계 화합물이 많이 함유된 보통포틀랜드 시멘트의 흡착률이 가장 크며, 시멘트풀 및 모르처의 유동성 손실이 작았으며 나프탈린계 고성능 감수제가 유동성 손실면에서 얼마간 유리하였다.