• Proceedings of the Korean Fiber Society Conference
• /
• 2001.10a
• /
• pp.175-178
• /
• 2001

일반적으로 점탄성 거동을 나타내는 고분자 액체의 전단유동특성(shear flow properties)을 평가하기 위하여 정상전단(steady shear), 동적전단(dynamic shear), 응력완화(stress relaxation) 그리고 크리프(creep) 및 크리프 회복(creep recovery) 실험 등이 활용되고 있다[1], 이때 영전단점도(zero shear viscosity)와 정상상태 회복 컴플라이언스(steady-state recoverable compliance)는 정상상태(steady state)에서 얻어지는 물리량으로, 각 실험방법으로부터 직접적 또는 간접적으로 측정이 가능하다. (중략)

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.341-344
• /
• 2008

Plastics is commonly used in consumer electronics because of it is high strength per unit mass and good productivity. But. using, transporting, and keeping of plastic component was happened post-deformation. As time goes by and temperature is changed, the post-deformation causes the problems of exterior design and performance. But, it is difficult to estimate the post-deformation by only thermal deformation analysis. Also, the estimation technique of the pest-deformation must be easily applied to product development and it should be reliable because development time of product is limited. In the paper. the process to predict the post deformation under cyclic thermal loadings was suggested. The process was applied to the real panel, and the deformation predicted by the analysis was compared with that of real test, which showed the possibility of applying the suggested process to predict the post deformation of plastic product under thermal loadings.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.14 no.1
• /
• pp.32-37
• /
• 2018

When designing high temperature piping system, creep phenomena must be considered. Since ASME code does not provide detailed methods of design by rule (DBR) for high temperature piping, Finite element analysis should be performed. However, In the case of piping system with frequent design changes, creep analysis of the entire piping system for every change is ineffective and practically impossible. Therefore, based on elastic and elastic-plastic analysis, which takes a relatively short time, the creep stress is predicted by using elastic follow-up factor method provided in R5 code and plastic-creep analogy presented by Hoff. The predicted creep stress for a virtual piping system was compared with the creep analysis result and the two results showed similar stress relaxation tendency in time.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.10
• /
• pp.873-881
• /
• 2008

Weld overlay is one of the residual stress mitigation methods which arrest crack initiation and crack growth. Therefore weld overlay can be applied to the region where cracking is likely to be. An overlay weld used in this manner is termed a preemptive weld overlay(PWOL). In pressurized water reactor(PWR) dissimilar metal weld is susceptible region for primary water stress corrosion cracking(PWSCC). In order to examine the effect of PWOL on residual stress mitigation, PWOL was applied to a specific dissimilar metal weld of Kori nuclear power plant by finite element analysis method. As a result, strong compressive residual stress was made in PWSCC susceptible region and PWOL was proved effective preemptive repair method for weldment.

• Korean Journal of Food Science and Technology
• /
• v.27 no.2
• /
• pp.193-198
• /
• 1995

The changes in the rheological properties of soybean curd upon the various storage temperatures ($5{\sim}25^{\circ}C$) were measured by the stress-relaxation test and analysed by time-temperature superposition theory. As the storage temperature was lower, higher initial and equilibrium stress of soybean curd were observed. When the stress-relaxation curves were moved horizontally by using the shift-factor on the basis of reference temperature, the master curve was obtained. By applying master curve and shift-factor to the WLF (Williams-Landel-Ferry) equation, activation energy (30kcal/mol) was calculated and storage time at the specific temperature could be predicted, suggesting the equivalent shelf-life of soybean curd texture.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.127-127
• /
• 2000

다이아몬드상 카본(Diamond-like Carbon, DLC) 필름은 비정질 재료로서 다이아몬드와 유사한 높은 경도, 내마모성, 화학적 안정성, 그리고 광학적 특성을 가지고 있으며, 낮은 마찰계수와 높은 탄성률 등으로 인해 많은 분야에서 응용이 연구되고 있는 재료이다. 그러나 DLC 필름이 이러한 우수한 특성이 가지고 있음에도 불구하고 수 GPa에 이르는 높은 압축 잔류 응력으로 인해 응용에 제약을 받고 있다. 이러한 압축 잔류 응력이 상당한 값에 이르게 되면 기판의 구속에서 벗어나게 되어, 기판으로부터 떨어지게 되고 굽힘을 받게 되는 delamination buckling 현상이 일어나기도 한다. 본 연구에서는 높은 잔류 응력으로 인해 자연적으로 발생하는 buckling 현상과 식각 과정을 통해 인위적으로 기판의 제한으로부터 필름을 완화시키는 freehang 방법을 이용하여 필름이 기판에 접착되는데 필요한 에너지를 평가하려고 한다. 본 실험에서는 rf-PACVD 장비를 이용하여 필름을 증착하였다. 이때 전극과 플라즈마 사이의 바이어스 음전압은 -100~700 Vb로 변화를 주었으며, 합성압력은 9mTorr로 고정하였다. 사용한 반응 가스는 메탄(CH4)이고, 아르곤(Ar)을 이용하여 모든 실험에서 동일하게 기판을 전처리 하였다. buckling 현상을 관찰하기 위해 사용된 기판은 slide glass이고, freehang을 제작하기 위해 사용된 기판은 (100) p-type Si wafer 이다. freehang 제작시 사용한 식각 용액은 KOH(5.6mol)이며 외부 요인을 제거하기 위해 7$0^{\circ}C$ 항온조를 사용하였다. Buckling 된 필름과 freehang은 광학 현미경과 전자 주사 현미경에 의해 관찰되었으며, 사인 함수 형태의 곡면을 가지고 있었다. 또한 freehang 제작시 각각의 주기와 진폭을 통해, 필름과 기판사이의 계면에너지와 buckling 되면서 새로 생성된 두 표면에너지 차이를 구할 수 있게 되고, 이를 통해 접착에너지를 평가할 수 있었다.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.100-100
• /
• 2009

This paper is concerned with numerical analyses of residual stresses in welds and material's susceptibility to stress corrosion cracking (SCC) for the primary piping system in nuclear power plants: Both the dissimilar metal weld (DMW) for stainless steel to low alloy steel joints and the similar metal weld (SMW) for forged stainless steel to cast stainless steel joints are considered. Thermal elasto-plastic analyses using the finite element method (FEM) are performed to predict residual stresses generated in fabrication welding and its related processes for both the DMW and SMW, including effects of quenching for cast stainless steel piping, machining of the DMW root, and grinding of the SMW root. As a result, the effect of quenching should be included in the evaluation of residual stresses in the SMW for the cast stainless steel piping. It is deemed that residual stresses in both the DMW and SMW would not affect the SCC susceptibility of the welds providing that the welding processes are completed without any weld repair on the inside wall of the joint. However, the grinding process if performed on the safe-end to piping weld, would produce a high level of residual stresses in the inner surface region and thus a stress improvement process (e.g. buffing) should be considered to reduce susceptibilities to SCC.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.36 no.4
• /
• pp.329-336
• /
• 2000

Welding is a important technological method in mechanical engineering. $CO_2$MAG(metal active gas) welding means that metal part in double capstan drum for the inshore and costal vessels are joined by melting(with or without a filler material) or that new material is added to a metal part by melting. The thermal stresses appear due to a non-uniform temperature field, inhomogeneous material properties, external restraint and volume changes during phase transformations. In this study analysis the elasto-plastic thermal stresses distribution of welding part in double capstan drum for the inshore and costal vessels using finite element method (FBM). Therefore it calculates the numerical value that can be applied to the optimum design of welding parts and the shapes. The significant results obtained in this study are summarized as fellows. At early stage of the cooling after welding process, the abrupt thermal stresses gradient has been shown in the vicinity of welding part. In the thermal stresses analysis due to temperature gradient and heat shocking maximum stress was occurred of welding part and stresses were distributed from 54MPa~48MPa.

• Journal of the Korean Magnetics Society
• /
• v.8 no.4
• /
• pp.185-191
• /
• 1998

Magnetic domain structure and static magnetic properties were investigated in the ultra thin 3%Si-Fe strip wound cores when the strips were wound and annealed to relief the stress. The elastic and plastic deformation due to the radius of curvature was also investigated for the cores. At the as-wound state, the maze pattern domain structure was generated on the concave surface of the core and 180$^{\circ}$ domain wall was recovered by annealing 600 $^{\circ}C$$\times$30 min. After annealed by 900 $^{\circ}C$$\times$30 min, Hc of strip-wound cores was not reached to the $H_c$ of the strip even at the cores of elastic deformation region. It is necessary to relief the local stress remained in the core when the cores were manufactured for the application of ultra-thin 3%Si-Fe strip.

• Journal of the Korean Society for Railway
• /
• v.14 no.2
• /
• pp.94-99
• /
• 2011

In this study, the stress reduction effect was evaluated for GFRP/Mg single lap bonded joints according to six different adherend shapes. Six different types of the single lap joint specimen were modeled and assessed using geometrically nonlinear finite element analysis. Moreover, three dimensional effect of stress distribution for the different adherend shapes was investigated. From the analysis, the dissimilar single lap bonded joint with the normal tapering and without the spew fillet (model 2) showed the highest stress values. In contrast, the peel stress values of both the square ended adherends with the spew fillet (model 3) and the reverse tapered adherends with the spew fillet (model 5) were 65.8% and 65.5% lower than the reference model.