• Journal of the Korea Concrete Institute
• /
• v.14 no.5
• /
• pp.726-733
• /
• 2002

Shrinkage strip or separation strip is a temporary joint that is left open for a certain time during construction to allow a significant part of the shrinkage to take place without inducing stress. A shrinkage stress analysis method of shrinkage strip in concrete slab of multi-story building considering the relaxation effect of creep and construction sequence is proposed. The analysis results of 10-story example building show that the effect of shrinkage strip can be analyzed easily by the proposed method. And shrinkage strip installed in a particular floor makes the stress of that floor reduced and the stress of the other floors increased a little. The rate and amount of stress reduced with closing time mainly depends on the development of shrinkage with time of concrete model used. The amount of stress reduced is determined by the amount of shrinkage strain developed before the closing of shrinkage strip.

• Journal of Energy Engineering
• /
• v.29 no.3
• /
• pp.91-96
• /
• 2020

For the anchor bolts and brackets that fix the stone wall, which is an external finishing material, it is necessary to maintain the performance required for the mechanical structure from the initial design stage and secure high durability. For this, the design and safety evaluation in consideration of the load conditions are necessary, so the structural analysis applying the finite element analysis technique was performed as a method to verify durability. As a result of structural analysis for various shapes for optimal design, a reinforcing structure was added to alleviate the maximum stress generated at the rear part of the bracket in contact with the bolt. In addition, a reinforcing plate was additionally attached to the bracket to relieve the stress concentration of the L-shaped bracket to make the stress distribution uniform, so that the safety factor satisfies the standard conditions. In addition, the fatigue life analysis by cyclic load was performed, and the fatigue safety factor was analyzed. As a result, the durability was obtained.

• Korean Journal of Food Science and Technology
• /
• v.24 no.4
• /
• pp.335-340
• /
• 1992

The amounts of salt diffused into radish after immersing in various concentrations of salt solution at different temperatures were measured and the changes of radish texture by the salt diffusion were estimated with the viscoelastic constants of a 3 element solid model determined by a stress relaxation test. The amount of salt diffused through radish was increased with increasing the salt concentration and soaking temperature. While the instantaneous stress, equilibrium elastic solid content and viscoelastic constants of radish were decreased as salt concentration and soaking temperature increased, the stress relaxed fast. Viscoelastic constants as well as the diffusivity were influenced by salt concentration more than by soaking temperature. The rheological equations for the predictable stress changes of radish after immersed in the salt solution at various conditions (temperature, salt concentration and impure salt) were suggested as a function of time.

• Journal of Conservation Science
• /
• v.17 s.17
• /
• pp.19-32
• /
• 2005

The exterior of Korean traditional wooden buildings have been painted with Danchung of painting method using glue and pigments. However because of losing traditional techniques and materials through the period of colonization and industrialization, many problems are occurring today. Especially after several years from painting, occurrence of scalings and flakings in painting layer is a serious problem. To improve weathering resistance of painting layer caused by stress from the difference of swelling and shrinkage between painting layer and wood plate, was examined by weathering tests. The stress is due to the hydrophilic property of wood, mechanical properties(tensile property and stress relaxation) of painting layer, and priming methods by various binders such as glue, acrylic emulsion(Primal AC-3444), acrylic resin(Paraloid B-72). Because stress relaxation of acrylic emulsion of which glasf transition temperature is below room temperature$(7^{\circ}C)$ is high, painting layers with acrylic emulsion generate no scalings and flakings and are in the most durable state in all weathering tests. Priming method which starts from low concentration to high concentration, is more effective to improve durability than other priming methods.

• Polymer(Korea)
• /
• v.27 no.2
• /
• pp.113-119
• /
• 2003

The thermal properties and crystallization behaviors of poly(ethylene terephthalate) (PET) were investigated by controlling the annealing conditions of PET sample, such as relative humidity, temperature, and time. The variations of moisture content, glass transition temperature ($T_g$) and cold crystallization temperature ($T_{\propto}$) were examined after annealing the PET sample. Subsequently crystallization process was performed with the annealed PET specimen, and then the degree of crystallinity and heat distortion temperature (HDT) of variously crystallized PET specimen were examined. Residual stress relaxation in the injection molded PET sample after annealing was also observed through polarized films. Moisture content in the PET specimen increased up to 6000 ppm with increasing the relative humidity, temperature, and time of annealing. $T_g$ and $T_{\propto}$ of the annealed PET specimen decreased with increasing moisture content. The degree of crystallinity increased as increasing moisture content in the PET specimen. However for same moisture content, the degree of crystallinity varied with annealing conditions. The relaxations of residual stress in the PET sample differed from annealing conditions, and the maximum degree of crystallinity increased with decreasing residual stress in the PET sample.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.10 s.181
• /
• pp.2552-2559
• /
• 2000

Most of ferrous b.c.c weld materials have martensitic transformation during rapid cooling after welding. It is well known that volume expansion due to the phase transformation could influence on the relaxation of welding residual stress. To apply this effect practically, it is necessary to establish a numerical model which is able to estimate the effect of phase transformation on residual stress relaxation quantitatively. For this purpose, the analysis is carried out in two regions, i.e., heating and cooling, because the variation of material properties following a phase transformation in cooling is different in comparison with the case in heating, even at the same temperature. The variation of material properties following phase transformation is considered by the adjustment of specific heat and thermal expansion coefficient, and the distribution of residual stress in analysis is compared with that of experiment by previous study. In this study, simplified numerical procedures considering phase transformation, which based on a commercial finite element package was established through comparing with the experimental data of residual stress distribution by other researcher. To consider the phase transformation effect on residual stress relaxation, the transition of mechanical and thermal property such as thermal expansion coefficient and specific heat capacity was found by try and error method in this analysis. In addition to, since the transformation temperature changes by the kind and control of alloying elements, the steel with many kinds of transformation temperature were selected and the effect of transformation on stress releasement was investigated by the numerical procedures considering phase transformation.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.10
• /
• pp.83-90
• /
• 1998

The effects of dopant activation anneal on GOI (Gate Oxide Integrity) of MOS capacitor with amorphous silicon gate electrode were investigated. It was found that the amorphous silicon gate electrode was crystallized and the dopant atoms were sufficiently activated by activation anneal. The mechanical stress of gate electrode that reveals large compressive stress in amorphous state, was released with increase of anneal temperature from $700^{\circ}C$ to 90$0^{\circ}C$. The resistivity of gate electrode polycrystalline silicon film is decreased by the increase of anneal temperature. The reliability of thin gate oxide and interface properties between oxide and silicon substrate greatly depends on the activation anneal temperature. The charge trapping characteristics as well as oxide reliability are improved by the anneal of 90$0^{\circ}C$ compare to that of $700^{\circ}C$ or 80$0^{\circ}C$. Especially, the lifetimes of the thin gate oxide estimated by TDDB method is 3$\times$10$^{10}$ for the case of $700^{\circ}C$ anneal, is significantly increased to 2$\times$10$^{12}$ for the case of 90$0^{\circ}C$ anneal. Finally, the interface trap density is reduced with relaxation of mechanical stress of gate electrode.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.28 no.2
• /
• pp.125-130
• /
• 2008

A spherical indentation has been proposed as a nondestructive method of measuring local residual stress field in laser-voided joints. The apparent yield strengths interpreted from the spherical indentation data of as-welded cutting wheel were compared with the intrinsic yield strengths measured at nearly equivalent locations in annealed wheel. Their difference along the distance from the welding line is welding stress distribution because the intrinsic yield strength is invariant regardless of the elastic residual stress. The spherical indentations show that the laser-welded diamond cutting wheel displays a 10 min-wide distribution of the welding residual stress and has peak compressive and tensile stresses in the shank and tip regions, respectively.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.4
• /
• pp.612-618
• /
• 1998

Monolithic SiC and SiC/C FGM layers were deposited on the graphite substrates by the CVD method and their thermal properties of the two specimens were investigated by thermal shock test for comparison. Temperature profiles and thermal stress distributions on thermal shock test were calculated by a commercially used computer program to see the thermal stress differences inside of two specimens. The specimens coated with FGM were expected to show a efficient relaxation of thermal stresses at the interface and they were not cracked under the actual $\Delta$T=1600 K experimental condition. This result proved that the experimental results were well accorded with the expectation from the theoretical calculations.

• Korean Journal of Materials Research
• /
• v.7 no.10
• /
• pp.908-913
• /
• 1997

플라즈마 화학 증착 방법에 의해 corning 7059 유리기판위에 비정질 실리콘 박막을 만들고 고온열처리, 다단계급속열처리, 일차원 선형빔(line shape beam)의 가우스 분포를 가지는 엑시머 레이저 열처리를 이용하여 고상 및 액상의 재결정화를 통해 다결정 실리콘 박막을 제작하였다. 편광된 라만 분광학(Raman spectroscopy)을 통하여 여러 가지 열처리 방법과 기판온도에 따른 다결정 실리콘 박막의 잔류응력을 조사하였다. 레이저 열처리에 의하여 결정화된 실리콘 기판의 경우, 높은 결정화된 체적량과 잔류응력을 갖으며 equaxial결정성을 갖는다. 그러나 이러한 고상 재결정화된 다결정 실리콘 박막은 라만스펙트럼에서 480$cm^{-1}$ /주위에 넓게 퍼져있어 비정질상(amorphous phase)이 함께 존재함을 알 수 있다. 고온열처리와 다단계급속열처리의 경우 잔류응력의 크기는 각각 4.07x$10^{9.}$과 4.56x$10^{9 dyne}$ $\textrm{cm}^2$이다. 또한 엑시머레이저 열처리의 경우 기판온도가 상온에서 40$0^{\circ}C$로 증가할수록 열적인 완화에 의해 잔류응력이 1.35x$10^{10}$에서 8.58x$10^{9}$dyne/$\textrm{cm}^2$으로 감소하는 것을 알 수 있다.다.