• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.196-199
• /
• 2010

본 연구는 판에 존재하는 유공형상에 따른 응력 집중 해석이다. 일반으로 판은 가공이 쉽고 제작이 편리하여 그 사용이 많다. 이러한 판의 연결에는 원형의 유공을 이용하는 경우가 많고 구조물의 중량감소를 목적으로 유공을 만드는 경우도 있다. 그러나 판에 존재하는 유공의 경우 응력 집중으로 인한 균열생성과 같은 단점을 가진다. 이를 보완하기 위해 유공부의 최적설계 및 응력해석과 같은 많은 연구들이 수행되고 있다. 본 연구에서는 원형, 정사각형과 정삼각형의 유공을 유한 요소 프로그램을 이용하여 시뮬레이션하고 유공형상에 따라 판에 발생하는 응답을 알아보았다. 또한 원형유공의 응답을 기준으로 정사각형과 정삼각형 유공의 모서리의 곡률반경을 변화시켰을 때 발생하는 응답을 비교하였다. 상용 유한 요소 프로그램인 ANSYS/Workbench를 사용하여 인장응력하의 유공판의 응답 해석을 수행하였으며 얻어진 결과를 유공의 형상, 곡률반경의 변화에 따라 분석하였다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.12 no.4
• /
• pp.681-690
• /
• 1999

본 논문에서는 요소를 사용하지 않은 수치해석기법인 무요소법 중에서 다중해상도(multi-resolution)특성이 내재되어 있는 Reproducing Kernel Particle Method (RKPM)의 이중스케일 분해기법을 사용하여 RKPM의 형상함수를 상단성분과 하단성분으로 분리하고 이를 3차원 선형탄성해석과정에 적용하여 von Mises 응력장의 상·하단성분을 유도하였다. 유도된 응력장의 상단성분을 이용하여 후처리과정을 거치지 않고도 응력의 고변화도 부위를 손쉽게 파악할 수 있는 기법을 개발하였으며 이를 이용한 효율적인 적응적 세분화기법의 적용가능성을 연구하였다. 대표적인 2차원 및 3차원 응력집중 문제에 적용하여 응력집중부위를 파악하고 간단한 적응적 세분화과정에 따른 절점추가를 통하여 해의 정도 향상을 파악해 본 결과, 본 연구에서 개발된 기법이 응력집중부위를 정확히 판정할 수 있었으며 효율적인 적응적 세분화기법의 유용한 도구로서 활용될 수 있음을 검증하였다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.6
• /
• pp.491-498
• /
• 2016

Stress on plates may increase in the neighborhood the edges or the holes for rivets or bolts. Excessive stress concentration may lead to severe breakage of the plates. Thus, it is important to conduct optimization of arrangement of holes at the design stage. In this paper, accuracy of FEM analysis was examined for such stress concentration. By changing the hole size on a narrow plate, change of the stress concentration factor(K) was investigated. Additionally, the same experiment was conducted about series of multiple holes on plate to investigate interaction between the adjacent holes. Then, the FEM results were compared to the reference predictions respectively. Finally, a method by which simple stress concentrating situations can be optimized, will be suggested. This method was examined by FEM, and showed similar tendency with the expectation. Therefore, this method can be valuable when arranging the holes on a plate.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.28 no.2
• /
• pp.92-100
• /
• 2016

Reliability analysis of tripod support structure for offshore wind turbine was performed. Extreme distribution function of peak response due to wind and wave loads was estimated by applying peak over threshold(POT) method. Then, stress based limit state function was defined by using maximum stress of support structure which was obtained by multiplying beam stress and concentration factor. The reliability analysis result was compared when maximum stress was calculated from shell element. Reliability index was evaluated using first order reliability method(FORM).

• Journal of Power System Engineering
• /
• v.13 no.4
• /
• pp.49-55
• /
• 2009

복합재 적층판의 자유단 근처에서 나타나는 층간 응력의 집중 현상을 층간면 효과를 고려해 해석하였다. 복합재 적층판 내부의 임의의 위치에서 3차원 평형방정식을 만족시키기 위해 렉니츠키 응력함수를 도입하였으며, 가상일의 원리를 이용하여 지배방정식을 유도하였다. 주어진 응력함수를 이용하여 구한 3차원 응력들은 복합재 적층판의 아래 위 면뿐만 아니라 자유단에서 하중자유조건을 잘 만족한다. 기하학적 불연속성 때문에 복합재 적층판의 자유단에서는 응력의 특이가 발생하지만, 층간면 효과를 고려하게 되면 층간응력의 집중현상을 정확하게 해석할 수 있다. 자유단에서 발생한 층간응력의 크기를 보면, 층간면 효과를 고려할 경우, 응력특이 효과가 많이 줄어드는 것을 관찰할 수 있다. 본 연구에서 주어진 층간면에서의 정확한 응력 해석은 복합재 적층판의 강도설계를 수행하는 초기 설계 툴로 사용할 수 있다.

• Asia-pacific Journal of Multimedia Services Convergent with Art, Humanities, and Sociology
• /
• v.5 no.2
• /
• pp.207-214
• /
• 2015

Stress concentrations around discontinuities, such as a hole or a sudden change in cross section of a structural member, have great important cause in the most materials failure because the stress near the points of application of concentrated loads can reach values much larger than the average value of the stress in the member. This paper presents the stress concentrations between fillet and hole at different locations in a stepped plate under tensile loading. The analysis for interaction effect of stress concentration was performed by photoelasticity and ANSYS which is a commercial finite element software. From the analysis results, the circular hole located at the different position from the fillet radius can cause different values of stress concentration factor within interacting region.

• Journal of the KSME
• /
• v.31 no.4
• /
• pp.356-363
• /
• 1991

선형 탄성 유한요소 응력해석과 평균응력 효과를 고려한 저주기 피로실험으로부터 결정된 피로 특성, 그리고 국부변형률 방법을 종합하여 외경에 흠이 존재하는 자긴가공된 두꺼운 압력 용기의 피로수명이 평가되었다. 직사각형의 매우 날카로운 흠에서의 응력집중계수는 타원형 홈에서의 응력집중계수의 약 두배의 값이 얻어졌으며, 고강도 압력용기강인 ASTM A723의 저주기 피 로거동에 대한 평균응력 영향은 Morrow 및 SWT 파라메타를 이용하여 충분히 고려되었다. 균열발생이 예상되는 위험한 부분인 홈의 뿌리부분에서의 국부적인 응력, 변형률이 계산되었으며 예측된 피로수명은 실험적으로 얻어진 수명과 비교했을 때 2에서 4배의 오차를 보이면서 일치 하는 결과를 얻었다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.5
• /
• pp.513-523
• /
• 2016

The stress concentration factors and stress intensity factors for a simple beam and a cantilever are analyzed by using finite element method and phtoelasticity. Using the analyzed results, the estimated graphs on stress concentration factors and stress intensity factors are obtained. To analyze stress concentration factors of notch, the dimensionless notch length H(height of specimen)/h=1.1~2 and dimensionless gap space r(radius at the notch tip)/h=0.1~0.5 are used. where h=H-c and c is the notch length. As the notch gap length increases and the gap decreases, the stress concentration factors increase. Stress concentration factors of a simple beam are greater than those of a cantilever beam. However, actually, the maximum stress values under a load, a notch length and a gap occur more greatly in the cantilever beam than in the simple beam. To analyze stress intensity factors, the normalized crack length a(crack length)/H=0.2~0.5 is used. As the length of the crack increases, the normalized stress intensity factors increase. The stress intensity factors under a constant load and a crack length occur more greatly in the cantilever beam than in the simple beam.

• Asia-pacific Journal of Multimedia Services Convergent with Art, Humanities, and Sociology
• /
• v.7 no.2
• /
• pp.437-444
• /
• 2017

Stress concentrations around discontinuities, such as a hole in cross section of a structural member, have great importance because the most materials failure around the region may be occurred. Stress on the point applied by concentrated load reaches much larger value than the average stress in structural member. In this paper, stress analysis was performed for the plate with a partial through-hole to find the difference of the principal stress distribution. The difference between maximum principal stress and minimum principal stress in photoelasticity is equal to the value obtained by multiplying the isochromatic fringe order by the fringe constant of the material divided by the distance through which the light passes, that is, the thickness of the specimen. Since the difference of principal stress is proportional to the photoelastic fringe order, the distribution of the principal stress difference by the finite element analysis can be compared with the photoelasticity experimental result. ANSYS Workbench, that is the finite element software, is used to compute the differences of principal stresses at the specific points on the measured lines. The computation values obtained by ANSYS are compared with the experimental measurements by photoelasticity, and two results are comparable to each other. In addition, the stress concentration factor is obtained using the stress distribution analyzed from the variation of hole depth. Stress concentration factor is increasing, as the depth of hole increase.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.1
• /
• pp.373-379
• /
• 2020

This study performed stress and fatigue life analysis of the damping hinge of a built-in side-by-side refrigerator that occurs when the door is opened to the maximum angle. An analysis of the initial design showed that stress concentration occurred at the corner between the cylinder and upper disk of the bracket pin, and the maximum stress exceeded the yield strength. The maximum stress location and the calculated fatigue life were consistent with the door opening-and-closing endurance test results for a prototype. Three cases of design improvement for the bracket pin were derived with the aim of reducing the stress concentration that appeared in the initial design. An analysis of the cases showed that inserting a fillet between the disk and the cylinder of the bracket pin reduced the stress and increased the fatigue life. Moreover, changing the disk into two steps was more favorable. In conclusion, the best design improvement was the case that the disk was changed to two steps and the fillet with a large radius was inserted. In that case, the stress was the smallest and the fatigue life was infinite.