• Korean Chemical Engineering Research
• /
• v.62 no.3
• /
• pp.269-273
• /
• 2024

The normal stress of TiO₂ ER fluid under an electric field showed negative values due to the electrostatic attraction force in the normal direction between particles and the absolute value increased dramatically with electric field strengths. The normal yield stress exhibited E² dependence similar to the dynamic yield stress, indicating that normal stress can be utilized for evaluating the ER effect. Numerical simulation demonstrated good qualitative agreement with the experimental data and suggested that the decrease in the absolute value of normal stress with increasing shear rates was attributed to the rearrangement of particle configurations under shear.

• Korean Chemical Engineering Research
• /
• v.58 no.3
• /
• pp.480-485
• /
• 2020

The extended Maxwell-Wagner polarization model is employed to describe the ER behavior of the conducting particle ER suspensions, and solutions to the equation of motion are obtained by dynamic simulation. The simulation results show the nonlinear ER behavior (Δτ∝Eⁿ, n≈1.5) of the conducting particle ER suspensions. The response point, where shear stress reaches steady-state, is the point where stable break-up and rebuild of the chain-like structure of particles reaches. Also, it shows the minimum of shear stress, which corresponds the start-up of random particle configuration. The shear stress reaches plateau as particle volume fraction increases.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.5
• /
• pp.205-215
• /
• 1999

Crushable sandy soil grounds are widely found along the coast throughout the world. The ground composed of lime sand, which is characterized by the material with high compressibility due to particle crushing contains carbonate calcium. In this study, in order to clarify the characteristics of the particle crushing as related to the strength and deformation properties of sands, isotropic compression test was carried out on three different types of carbonate sands and a silica sand. A crushability index, K, is proposed in connection with the yielding and particle crushing stress of sands at various relative densities under isotropic compression. It is concluded that the representative crushability index, K, associated with the soil particle strength, can be a key factor in preliminary parameters in evaluating soil crushability.

• Journal of Digital Convergence
• /
• v.14 no.12
• /
• pp.193-199
• /
• 2016

MR(magnetorheological) devices for vehicle applications requires the consistent control performance and the reliable operation. However, the corrosion of iron particles consisting the MR fluid can significantly affect on MR properties. This paper presents an effect of the MR particle corrosion on the performance of MR fluids such as shear stress magnitude which is directly concerned with control performance. As a first step, MR particles are corroded by water-calcium chloride solution. The resulting MR particles are examined by scanning electron microscope (SEM) and their molar ratios are analyzed by the energy dispersive X-ray analysis (EDAX). By dispersing the corroded MR particles into silicone oil, the corroded MR fluid is synthesized for evaluation of MR effect change. A rotational viscometer is adopted to measure shear stress magnitude. Finally, it is demonstrated how much the corrosion affect on performances by comparing the normal MR fluid to the corroded MR fluid, from which performance investigation of the MR devices containing the corroded MR particles will be studied in the second phase of this study.

• Journal of Korea Game Society
• /
• v.14 no.6
• /
• pp.49-58
• /
• 2014

In particle-based fluid simulation, the yield stress is required for the deformation of the viscoelastic material like gel. von Mises's yield condition has been proposed to implement deformation of viscoelastic objects, but did not express the explosion. Furthermore, von Mises's yield condition is hard to approximate. We propose an ideal yield condition for viscoelastic object that reference from Tresca's yield condition. Unlike conventional particle-based simulation approximate the external power by the deformed length of the object, this paper is approximate the external power by area of the object. We check up that explosion was realistic when a viscoelastic object is compressed under the ideal yield condition.

• Tunnel and Underground Space
• /
• v.30 no.6
• /
• pp.573-590
• /
• 2020

This study presents the current status of DECOVALEX-2023 project Task G and our research results so far. Task G, named 'Safety ImplicAtions of Fluid Flow, Shear, Thermal and Reaction Processes within Crystalline Rock Fracture NETworks (SAFENET)' aims at developing a numerical method to simulate the fracture creation and propagation, and the coupled thermohydro-mechanical processes in fracture in crystalline rocks. The first research step of Task G is a benchmark simulation, which is designed for research teams to make their modelling codes more robust and verify whether the models can represent an analytical solution for displacements of a single rock fracture. We reproduced the mechanical behavior of rock and embedded single fracture using a three-dimensional grain-based distinct element model for the simulations. In this method, the structure of the rock was represented by an assembly of rigid tetrahedral grains moving independently of each other, and the mechanical interactions at the grains and their contacts were calculated using 3DEC. The simulation results revealed that the stresses induced along the embedded fracture in the model were relatively low compared to those calculated by stress analysis due to stress redistribution and constrained fracture displacements. The fracture normal and shear displacements of the numerical model showed good agreement with the analytical solutions. The numerical model will be enhanced by continuing collaboration and interaction with other research teams of DECOVALEX-2023 Task G and validated using various experiments in a further study.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.2
• /
• pp.87-97
• /
• 2008

Behaviors of cemented engineered soils, composed of rigid sand particle and soft rubber particle, are investigated under $K_o$ condition. The uncemented and cemented specimens are prepared with various sand volume fractions to estimate the effect of the cementation in mixtures. The vertical deformation and elastic wave velocities with vertical stress are measured. The bender elements and PZT sensors are used to measure elastic wave velocities. After cementation, the slope of vertical strain shows bilinear and is similar to that of uncemented specimen after decementation. Normalized vertical strains can be divided into capillary force, cementation, and decementation region. The first deflection of the shear wave in near field matches the first arrival of the primary wave. The elastic wave velocities dramatically increase due to cementation hardening under the fixed vertical stress, and are almost identical with additional stress. After decementation, the elastic wave velocities increase with increase in the vertical stress. The effect of cementation hinders the typical rubber-like, sand-like, and transition behaviors observed in uncemented specimens. Different mechanism can be expected in decementation of the rigid-soft particle mixtures due to the sand fraction. a shape change of individual particles in low sand fraction specimens; a fabric change between particles in high sand fraction specimens. This study suggests that behaviors of cemented engineered soils, composed of rigid-soft particles, are distinguished due to the cementation and decementation from those of uncemented specimens.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.5C
• /
• pp.209-218
• /
• 2010

In residual soils, large particles such as rock fragments or gravel are surrounded by sand or clay. The strength of such granular mixtures can be controlled by the concentration of fine or coarse grains. The percentage by weight, size or shape of gravel in the mixture that can control the strength of the mixture has not been clearly determined for various granular mixtures. In this study, the effect of dispersed gravels on the shear characteristics of sand was evaluated. Large and small gravels were inserted in the middle of each layer with moist Nakdong River sand and compacted into a cylindrical sample with five equal layers. Embedded gravel ratios by weight were 0, 3, 9, and 14%. After consolidation, a series of undrained triaxial compression tests was performed on Nakdong River sand with dispersed gravels. Maximum deviator stresses of the Nakdong River sand with large gravels decrease up to 38% as a percentage of embedded gravels increases. Such strength degradation decreases as a confining pressure increases. The maximum deviator stress increases as the percentage by weight of small gravel increases; at 3 or 9% of gravel weight it slightly increases but at 14% of gravel weight it increases up to 34%.

• The Journal of Engineering Geology
• /
• v.24 no.1
• /
• pp.23-38
• /
• 2014

The composition of carbonate sands from a sabkha at Ruwais in the UAE differs from that of silica sand, and these sands are crushed easily under low compression pressures. Accordingly, particle crushing of carbonate sand occurs under high pressure, which results in additional settlement and reduces the shear strength. In this study, consolidation and triaxial tests were conducted to analyze the characteristics of carbonate sands following particle crushing. The unusual shear strength graphs of the carbonate sands result from the degree of particle pre-crushing. For the range at p' > p in the p (p')-q diagram, negative (-) excess porewater pressures occur if the axial pressure causes particle crushing that induces exposure of the inner voids. In addition, the q value decreased after particle crushing. In conclusion, the unusual characteristics of the carbonate sands were induced by particle crushing. The triaxial tests revealed that the degree of particle pre-crushing influenced the excess porewater pressure.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.06a
• /
• pp.707-708
• /
• 2009