• Korean Journal of Materials Research
• /
• v.25 no.5
• /
• pp.226-232
• /
• 2015

High temperature plasma coating technology has been applied to recover damaged aluminum dies from wear by spraying pure aluminum and alumina powder. However, the coated mixed powder layer composed of aluminum and alumina often undergoes a detachment from the substrate, making the coated substrate die unable to maintain its expected life span. In this study, in order to increase the bonding strength between the substrate and the coating layer, a pure aluminum layer was applied as an intermediate bond layer. In order to prepare the specimen with variable bond coating conditions, the bond coat layers with a various gun speed from 10 cm/sec to 30 cm/sec were prepared with coating cycle variations ranging from three to nine cycles. The specimen with a bond coat layer coated with a gun speed of 20 cm/sec and three coating cycles exhibited ~13MPa of adhesion strength, while the specimen without a bond coat layer showed ~6 MPa of adhesion strength. The adhesion strength with a variation of bond coat layer thickness is discussed in terms of coating parameters.

• Korean Journal of Food Science and Technology
• /
• v.27 no.4
• /
• pp.506-515
• /
• 1995

The cultural characteristics of 60 strains of psychrotrophic lactic acid bacteria which were isolated from kimchi, a Korean traditional fermented vegetable food, and identified as Leuconostoc mesenteroides subsp. mesenteroides, Leu. mesenteroides subsp. dextranicum, Leu. paramesenteroides, Leu. lactis, Lactobacillus bavaricus and Lac. homohiochii were tested. All strains grew at $5^{\circ}C,\;10^{\circ}C\;and\;37^{\circ}C$ in tomato glucose broth, but not at $45^{\circ}C$. The optimum growth temperature of Leu. mesenteroides and Lactobacillus sp. were $33{\sim}34^{\circ}C\;and\;34{\sim}36^{\circ}C$, respectively. All strains of Leu. mesenteroides and Lactobacillus sp. grew at 4.8 and 4.2 of initial pH, but not at 4.0. The final pH of Leu. mesenteroides and Lactobacillus sp. in glucose broth were $3.84{\sim}4.10\;and\;3.82{\sim}3.99$, respectively. None of the 60 strains clotted milk nor reduced litmus in litmus milk. All strains of Leu. mesenteroides and Lactobacillus sp. grew in tomato glucose broth containing 7% ethanol or 6.5% NaCl, but not in the broth containing 15% ethanol or 10% NaCl. All strains grew in tomato glucose broth containing 40% bile juice and survived in the artificial gastric juice of pH 3.5. Furthermore, all strains of Leu. mesenteroides survived in the artificial gastric juice of pH 3.0. Since many strains of lactic acid bacteria tested in this study showed differences in several physiological characteristics from those described in Bergey's Manual of Systematic Bacteriology, it was considered that further tests would be necessary to clarify their positions in taxonomic system.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.18 no.5
• /
• pp.195-199
• /
• 2008

Production of the silicon feedstock for the semiconductor industry cannot meet the requirement for the solar cell industry because the production volume is too small and production cost is too high. This situation stimulates the solar cell industry to try the lower grade silicon feedstock like UMG (Upgraded Metallurgical Grade) silicon of 5$\sim$6 N in purity. However, this material contains around 1 ppma of dopant atoms like boron or phosphorous. Calculation of the composition profile of these impurities using segregation coefficient during crystal growth makes us expect the change of the type from p to n : boron rich area in the early solidified part and phosphorous rich area in the later solidified part of the silicon ingot. It was expected that the change of the growth speed during the silicon crystal growth is effective in controlling the amount of the metal impurities but not effective in reducing the amount of dopants.

• Resources Recycling
• /
• v.20 no.5
• /
• pp.34-39
• /
• 2011

Metallurgical grade silicon(MG-Si) was melted with Ca at 1500$^{\circ}C$ under Ar atmosphere. The sample was cooled at 10 $^{\circ}C$/min to room temperature and leached in aqua regia. In the present study, the effect of Ca addition and conditions of acid leaching on removal of Fe and P in MG-Si were investigated. CaSi$_2$ phase was formed at the grain boundary of MG-Si melting with Ca. Also FeSi$_2$ phase was precipitated in CaSi$_2$ phase. By the formation of CaSi$_2$ phase, 97% of Fe and 66 % of P were removed from Ca added MG-Si with the particle size of 600~850${\mu}m$ by aqua regia(more than 30%) leaching.

• Journal of Ocean Engineering and Technology
• /
• v.3 no.2
• /
• pp.125-137
• /
• 1989

To check technical improvement in the soundness and strength of 12% Cr steel rotor, a 25 tons of rotor with 65 tons of ingot was made in real size and was cut to pieces to take test samples, and the various mechanical tests such as impact, tensile, creep, and fatigue were carried out. The strengths are compared with those of 1% Cr-Mo-V rotor of same size. Microstructures of the samples are examined and reviewed. The results can be summarized as follows. 1) Fracture appearance transition temperatures are 80.deg. C at the center part and 60.deg. C near surface of 12% Cr rotor, and 8.deg. C near surface of 1% Cr-Mo-V rotor. 2) Comparative rapid softening occurs at higher temperatures above 600.deg. C for 12% Cr steel and 550.deg. C for 1% Cr-Mo-V steel in tension tests. 3) Fatigue crack propagation rate of 12% Cr steel is almost same as that of 1% Cr-Mo-V steel at the same corresponding surface part of the rotors. The crack growth rate of center part of 12% Cr rotor is faster than near surface part of the rotor, and the crack growth rate at the load condition of R=0.04 is slower than that of the load condition of R=0.5 for both 12% Cr steel and 1% Cr-Mo-V steel. 4) Crack growth rate of radial direction near surface of 12% Cr rotor is faster than that of transverse direction at the same part because of the difference in residual stresses. 5) Both creep and fatigue strengths of 12% Cr steel are superior to those of 1% Cr-Mo-V steel and the difference is thought the effect of climb and glide controlled creep by solid solution of alloying elements and dispersion of carbides.

• Journal of Ocean Engineering and Technology
• /
• v.3 no.2
• /
• pp.625-625
• /
• 1989

To check technical improvement in the soundness and strength of 12% Cr steel rotor, a 25 tons of rotor with 65 tons of ingot was made in real size and was cut to pieces to take test samples, and the various mechanical tests such as impact, tensile, creep, and fatigue were carried out. The strengths are compared with those of 1% Cr-Mo-V rotor of same size. Microstructures of the samples are examined and reviewed. The results can be summarized as follows. 1) Fracture appearance transition temperatures are 80.deg. C at the center part and 60.deg. C near surface of 12% Cr rotor, and 8.deg. C near surface of 1% Cr-Mo-V rotor. 2) Comparative rapid softening occurs at higher temperatures above 600.deg. C for 12% Cr steel and 550.deg. C for 1% Cr-Mo-V steel in tension tests. 3) Fatigue crack propagation rate of 12% Cr steel is almost same as that of 1% Cr-Mo-V steel at the same corresponding surface part of the rotors. The crack growth rate of center part of 12% Cr rotor is faster than near surface part of the rotor, and the crack growth rate at the load condition of R=0.04 is slower than that of the load condition of R=0.5 for both 12% Cr steel and 1% Cr-Mo-V steel. 4) Crack growth rate of radial direction near surface of 12% Cr rotor is faster than that of transverse direction at the same part because of the difference in residual stresses. 5) Both creep and fatigue strengths of 12% Cr steel are superior to those of 1% Cr-Mo-V steel and the difference is thought the effect of climb and glide controlled creep by solid solution of alloying elements and dispersion of carbides.

• Journal of Power System Engineering
• /
• v.14 no.2
• /
• pp.71-77
• /
• 2010

This paper was studied on microstructure, mechanical properties and corrosion characteristics of 316L stainless steel pipe welds was fabricated by orbital welding process. S-Ar specimen was fabricated by using Ar purge gas and S-$N_2$ specimen was fabricated by using $N_2$ purge gas. Ferrite was not detected in weld metal of S-$N_2$ specimen but the order of 0.13 Ferrite number(FN) was detected in weld metal of S-Ar specimen. Oxygen and Nitrogen concentration of S-$N_2$ specimen was higher than S-Ar specimen on HAZ and inner bead. The welds microstructural characteristics of S-Ar and S-$N_2$ specimens are similar. The microvickers hardness values of S-Ar and S-$N_2$ specimens welds were similar and average values of each regions were in the range of 174~194. The microstructures of S-Ar and S-$N_2$ weld metal were full austenite by primary austenite solidification. The Solidification structures of S-Ar and S-$N_2$ weld metal were formed directional dendrite toward bead center. The potentiodynamic polarization curve of STS 316L pipe welds exhibited typical active, passive, transpassive behaviour. Corrosion current density$(I_{corr.})$ and corrosion rate values of S-Ar specimen in 0.1M HCl solution were $0.95{\mu}A/cm^2$ and $0.31{\mu}A$/year respectively. The values of S-$N_2$ specimen were $1.4{\mu}A/cm^2$ and $0.45{\mu}m$/year.

• Korean Journal of Materials Research
• /
• v.12 no.12
• /
• pp.897-903
• /
• 2002

Morphological evolution and growth mechanism at the solid/liquid interface during solidification were investigated in the Ni-base superalloy GTD111M by directional soldification and quenching(DSQ) technique. The experiments were conducted by changing solidification rate(V) and thermal gradient(G) which are major solidification process variables. High thermal gradient condition could be obtained by increasing the furnace temperature and closely attaching the heating and cooling zones in the Bridgeman type furnace. The dendritic/equiaxed transition was found in the G/V value lower than $0.05$\times$10{^3}^{\circ}C$s/$\textrm{mm}^2$, and the planar interface of the MC-${\gamma}$ eutectic was found under $17 $\times$ 10{^3}^{\circ}C$ s/$\textrm{mm}^2$. It was confirmed that the dendrite spacing depended on the cooling rate(GV), and the primary spacing was affected by the thermal gradient more than solidification rate. The dendrite lengths were decreased as increasing the thermal graditne, and the dendrite tip temperature was close to the liquidus temperature at $50 \mu\textrm{m}$/s.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.7-7
• /
• 2009

TIG 용접에서는 후판 용접의 경우 용입의 한계 때문에 깊고 넓은 그루브 가공을 하여 다층 용접을 한다. 이 때, 그루브를 채우는 용착금속에 의한 응고 수축과 과대한 입열로 인한 변형이 문제시 되고 있다. 변형을 줄이기 위해서는 용착금속의 양과 입열량을 줄여야 한다. 이러한 문제를 해결하기 위해 그루브의 루트패이스를 두껍게 하고 그루브각을 줄여서 용착량을 줄인다. 이때, 좁은 그루브에서 두꺼운 루트패이스를 완전 용입할 수 있는 용접 프로세스가 필요하다. 비드가 좁고 깊은 용입 특성을 가지는 Plasma welding(PAW) 경우에는 좁은 그루브 속에 토치가 접근하기 어려워 적용하기 어렵다. 따라서 접근성이 용이한 TIG 용접에서 높은 용입형상비를 가지는 용접공정 개발이 필요하다. 선행연구로 높은 용입 형상비를 가지는 Active flux Tungsten Inert Gas(ATIG) 용접이 연구되었다. ATIG의 용입 증가 메커니즘으로는 Marangoni effect, 음이온들로 인한 아크 수축 효과, 절연 플럭스에 의한 아크 수축효과 등으로 알려져 있다. 또한 선행연구에서 ATIG에서 Ar가스에 He 또는 $H_2$ 가스를 첨가하면 용입이 더욱 증가하는 것을 확인하였다. 본 연구에서는 A-TIG에 He 가스를 적용하고 아크길이 0.5mm, 1.0mm, 2.0mm와 전극 선단각 30도, 60도, 90도에 따른 용입 형상비와 변형량을 검토하기 위해 실험을 하였다. 실험 결과는 아크길이가 감소할수록 전극 선단각이 증가할수록 용입 형상비는 증가하였고, 변형량은 감소하였다.

• Fire Science and Engineering
• /
• v.31 no.6
• /
• pp.83-90
• /
• 2017

If an overcurrent exceeding the rated value is applied to an electric wire, the temperature of the electric wire increases, and the electric wire covering deteriorates to cause a short circuit. The upper limit temperature of the wire varies according to the magnitude of the overcurrent. When a short circuit occurs at each upper temperature limit, a cooling speed difference occurs during the solidification process due to the temperature difference between the short circuit temperature and the wire surface temperature. At this time, the pattern characteristics of the dendritic structure formed on the molten cross section are different. In this study, the upper temperature limit, which varied according to the overcurrent magnitude, was measured. At the time a short circuit occurred, the second branch spacing (dendrite Arm Spacing : DAS) of the dendrite was analyzed and the numerical value was quantified. The experimental results showed that the upper temperature limit increases with the magnitude of the overcurrent, and that the second branch spacing increases with increasing wire temperature.