• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.5
• /
• pp.529-535
• /
• 2011

In this study, evaluation of acoustic emission signals characteristics for the post weld heat treated (PWHT) multi-pass weldment and weldment was dealt. Charpy standard specimens were taken from the lowest, middle and highest regions of the weld block. Pre-crack was made using the repeated load. Four point bend and AE tests were conducted simultaneously. Regardless of the specimens, AE signals were absent within elastic region and produced in the process of plastic deformation. AE signals for all specimens were not emitted after the maximum load. Value of signal strength for the all PWHT specimens was lower than that of the weldment. Besides, relations of plastic deformation zone size and accumulated AE counts for the PWHT specimens were more simple compared with the weldment. In case of the PWHT specimen, particles on the fractured surface decreased prominently compared with the weldment due.to PWHT. From these results, it can be concluded that PWHT was effective in reducing the AE sources for the weldment.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.5
• /
• pp.430-435
• /
• 2013

This study is investigation of the characteristics for acoustic emission signal generated by destruction on glass fiber bundles and specimen that was machined composite materials surrounding the outside of GFRP cylinder. The Amplitude of acoustic emission signal gets bigger as the cutting angle of knife increases. Accordingly, the number of hits in destruction of composite materials specimen have more in longitudinal direction (longitudinal direction to the glass fiber) than in hoop direction (horizontal direction to the glass fiber) while the amplitude of signals were bigger in hoop direction than longitudinal direction. It was found out that the amplitude of the glass fiber breakage is more than 40 dB and that the amplitude of signal for matrix crack was less than 40 dB because matrix crack signal was not observed when threshold value is 40 dB and matrix crack signal suddenly appered when threshold value is 32 dB. The slope of the amplitude is related to the acoustic emission source and the slope of the amplitude of the horizontal and vertical directions are 0.16 and 0.08. In particular, The slope of the amplitude of longitudinal direction breakage appear similar to the glass fiber breakage and therefore Acoustic emission source of longitudinal direction breakage is estimated the glass fiber breakage.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.04a
• /
• pp.293-298
• /
• 2003

This study deals with the source location method of defect which can be occurred in structure. The existing methods was very difficult to be applied to predict it because of using very complex numerical formula. The triangulation method which was proposed in his study can predict the source location predicted easily with small amount of data. Wave arrival time data can be directly converted into source-sensor distance is known. For this purpose, the propagation velocity was measured by Rayleigh wave, and the propagation behavior was analyzed. For the consideration of jointed part in structure, the source location method was applied to the welded workpiece. The signal propagation velocity was measured in welding part for the purpose of application to the part and the revised algorithm of source location was proposed.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.26 no.1
• /
• pp.1-7
• /
• 1990

Theoretical evaluations of the vertical displacement at the epicenter on the circular glass plate have been carried out in the case of the unit point loading(1 dyne force strength) with the Heaviside step-function time dependency. Acoustic emission signals generated during pencil lead($\Phi$=0.5mm, HB) fracture on the soda-lime glass($\Phi$=22cm, thickness=2.8cm) were observed by the optical Michelson interferometer with the stabilized circuit, and then the source function of the observed acoustic emission signals was analyzed by the deconvolution method. The source function of acoustic emission during pencil lead fracture had a 'dip' of~0.7$\mu$sec duration time at the front portion and a step function of~0.5$\mu$sec rise time with a force strength of~4.5N.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1998.06d
• /
• pp.9-12
• /
• 1998

공기경계층을 갖는 유리평판에서 힘의 크기가 10N이고 상승시간이 약 280ns 인 경사 점하중이 인가된 경우에 대하여 진앙점에서 입자 변위와 입자 속도를 계산하였다. 이론적으로 계산된 수직성분이 입자속도가 PZT변환자에 입사한다고 가정하여 PZT 변환자의 과도 응답특성을 Mason 등가회로와 격자점을 이용하여 계산하였다. 유리모세관의 파과시에 방출괴는 과도탄성파를 이용하여 유리평판의 진앙점에서 PZT 변환기의 응답을 조사하였고, 이론과 비교한 결과 상당히 일치하였다. 이를 이용하여 음향방출 시스템인 발생원, 전파매질, 변환자 및 신호분석시스템을 수학적으로 모형화할 수 있는 기초를 마련하였다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.3
• /
• pp.246-253
• /
• 2003

The initiation and growth of short fatigue cracks in the simulated aircraft structure with a series of rivet holes was detected by acoustic emission (AE). The location and the size of short tracks were determined by AE source location techniques and the measurement with traveling microscope. AE events increased intermittently with the initiation and growth of short cracks to form a stepwise increment curve of cumulative AE events. For the precise determination of AE source locations, a region-of-interest (ROI) was set around the rivet holes based on the plastic zone size in fracture mechanics. Since the signal-to-noise ratio (SNR) was very low at this early stage of fatigue cracks, the accuracy of source location was also enhanced by the wavelet transform do-noising. In practice, the majority of AE signals detected within the ROI appeared to be noise from various origins. The results showed that the effort of structural geometry and SNR should be closely taken into consideration for the accurate evaluation of fatigue damage in the structure.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.1
• /
• pp.39-45
• /
• 2001

Fourier transform has been one of the most common tools to study the frequency characteristics of signals. With the Fourier transform alone, however, it is difficult to tell whether signal's frequency contents evolve in time or not. Except for a few special cases, the frequency contents of most signals encountered in the real world change with time. Time-frequency analysis methods are developed recently to overcome the drawbacks of Fourier transform, which can represent the information of signals in time and frequency at the same time. In this study, damage process of a cross-ply carbon fiber reinforced plastic (CFRP) under monotonic tensile loading was characterized by acoustic emission. Different kinds of CFRP specimens were used to determine the characteristics of AE signals. Time-frequency analysis methods were employed for the analysis of fracture mechanisms in CFRP such as mix cracking, debonding, fiber fracture and delamination.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.17 no.4
• /
• pp.42-47
• /
• 2009

Recently, the wide range of the composite materials is used for the making airplanes, trains and automobiles body for the lightweight. Despite having complex structures, composite materials usually have well defined mechanical characteristics. However, composite materials are difficult to understand the fracture mechanism clearly by simple mechanical test. Nondestructive evaluation (NDE) combined with mechanical testing can play a more important role and especially Acoustic Emission Testing (AET) would become known to be a useful tool to assess damage and fracture behavior of composites. In this study The experiment was performed to acquire the acoustic emission signal during tensile test using unidirectional CFRP specimen and the data was analyzed the acoustic emission parameters with the waveform.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.8
• /
• pp.57-64
• /
• 2004

This study deals with the prediction of defect location which can be occurred in structure. The existing methods was very difficult to be applied to predict it, because of complex numerical formula. The triangulation method proposed in this study can predict the source location easily with small amount of data. The arrival time of wave can be directly converted into the distance between sensors. For this purpose, the propagation velocity was measured by Rayleigh wave, and the propagation behavior was analyzed. The welded workpiece is adapted to investigate for the consideration of jointed part in structure, The propagation velocity of signal was measured in welded workpiece and the revised algorithm of source location was proposed.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.1
• /
• pp.48-57
• /
• 2007

The fatigue crack growth behavior of a cracked and patch-repaired Ah2024-T3 panel has been monitored by acoustic emission(AE). The overall crack growth rate was reduced The crack propagation into the adjacent hole was also retarded by introducing the patch repair. AE signals due to crack growth after the patch repair and those due to debonding of the plate-patch interface were discriminated by usiag the principal component analysis. The former showed high center frequency and low amplitude, whereas the latter showed long rise tine, low frequency and high amplitude. This type of AE signal recognition method could be effective for the prediction of fatigue crack growth behavior in the patch-repaired structures with the aid of AE source location.