• The Journal of Engineering Geology
• /
• v.27 no.3
• /
• pp.323-330
• /
• 2017

For the formation identification, surface geological survey, drill core analysis, core description and well log analysis are widely used. Among them well log analysis is a popular method with drill core analysis, since it measures continuously physical properties at in-situ. In this study we calculated Thomsen anisotropic parameters (${\varepsilon},\;{\delta},\;{\eta}$) after applying Backus averaging method to the P wave velocity, S wave velocity, and density logs. The well log data application of Blackfoot, Canada, shows the formation could be divided by 12 layers. This shows that Thomsen anisotropic parameters for identifying formation using anisotropic parameters is useful if there is no natural gamma log that is widely used for the formation identification.

• Journal of the Korean Geophysical Society
• /
• v.4 no.2
• /
• pp.95-102
• /
• 2001

As a basic study of characterizing fracture condition in bore hole, conventional geophysical well log data consisting of sonic, gamma-gamma and resistivity logs were compared with geological core log and acousic televiewer log in limestone geology. Discontinuities shown on the acoustic televiewer log and the core log show fairly good correlation. The conventional Geophysical log is also shown to bi effective in locating discontinities in limestone geology; sonic log shows the best result and resistivity shows the worst. Particularly, the combination method of density and sonic logs is shown to be the most effective in delineating discontinuities.

• Geophysics and Geophysical Exploration
• /
• v.10 no.4
• /
• pp.299-307
• /
• 2007

Slowness time coherence (STC) technique has been applied to 3-receiver slim hole sonic log using 3 NX sized concrete model holes of different physical properties. We analyzed the effects of different source center frequencies on the wave forms, their amplitude spectra, and their STC results. We could determine the sonic velocity of each mode accurately by the application of STC method with the semblance projection and efficient selection of center frequency. Theoretical model and experimental model hole studies indicate that 4-receiver condition is the most ideal for STC in near surface slim hole sonic log. The result also indicates that favorable STC result can be obtained from three-receiver sonic log provided with the help of the first arrival picking method.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2006.06a
• /
• pp.225-231
• /
• 2006

As a study of efficient velocity analysis in sonic log, several preexisting techniques have been adopted to the sonic data taken from model borehole in Kangwon National University, and the results were compared. For the data taken from monopole source, Slowness-Time Coherence method which is a common technique for nondispersive wave was used. For the data taken from dipole source, conventional STC and Tang's method(Tang et al., 1995) were used. From the good matches in the P and Stoneley wave velocities, we could confirm the effectiveness of STC computation. We also could find that shear velocity obtained from Tang's method were exactly matched with shear velocity obtained from monopole source, and that the velocity were within the range of S wave velocity values obtained from conventional STC application to dispersive flexural waves.

• Proceedings of the KSEG Conference
• /
• 2000.04a
• /
• pp.231-236
• /
• 2000

• Proceedings of the KSEEG Conference
• /
• 2002.04a
• /
• pp.188-190
• /
• 2002

• Geophysics and Geophysical Exploration
• /
• v.9 no.1
• /
• pp.19-29
• /
• 2006

The first Japanese pilot-scale $CO_2$ sequestration project has been undertaken in an onshore saline aquifer, near Nagaoka in Niigata prefecture, and time-lapse well logs were carried out in observation wells to detect the arrival of injected $CO_2$ and to evaluate $CO_2$ saturation in the reservoir. $CO_2$ was injected into a thin permeable zone at the depth of 1110m at a rate of 20-40 tonnes per day. The total amount of injected $CO_2$ was 10400 tonnes, during the injection period from July 2003 to January 2005. The pilot-scale demonstration allowed an improved understanding of the $CO_2$ movement in a porous sandstone reservoir, by conducting time-lapse geophysical well logs at three observation wells. Comparison between neutron well logging before and after the insertion of fibreglass casing in observation well OB-2 showed good agreement within the target formation, and the higher concentration of shale volume in the reservoir results in a bigger difference between the two well logging results. $CO_2$ breakthrough was identified by induction, sonic, and neutron logs. By sonic logging, we confirmed P-wave velocity reduction that agreed fairly well with a laboratory measurement on drilled core samples from the Nagaoka site. We successfully matched the history changes of sonic P-wave velocity and estimated $CO_2$ saturation a(ter breakthrough in two observation wells out of three. The sonic-velocity history matching result suggested that the sweep efficiency was about 40%. Small effects of $CO_2$ saturation on resistivity resulted in small changes in induction logs when the reservoir was partially saturated. We also found that $CO_2$ saturation in the $CO_2$-bearing zone responded to suspension of $CO_2$ injection.

• Geophysics and Geophysical Exploration
• /
• v.1 no.3
• /
• pp.183-187
• /
• 1998

Seismic waveform estimation is based on the assumption that the seismic trace tying a well is one dimensional convolution of the propagating seismic waveform and the reflectivity series derived from well logs (sonic and density). With this assumption, the waveform embedded in a seismic trace can be estimated using a Wiener match filter. In this paper, I experimented a preprocessing procedure that applies both on the seismic trace and on the reflectivity series. The procedure is based on the assumption that the travel time can be estimated better from the seismic trace and that the instantaneous reflectivity values can be measured better on the well log. Thus the procedure is, 1) start-time adjustment and dynamic differential stretches are applied on the sonic log, and 2) seismic amplitudes are balanced such that the low frequency part of the seismic are matched to that of the reflectivities derived from well logs.

• Geophysics and Geophysical Exploration
• /
• v.8 no.1
• /
• pp.112-117
• /
• 2005

Geophysical logging is routinely undertaken as part of most coal mine exploration programs. Currently, the main application for the logs is to determine coal seam depth and to qualitatively estimate coal quality, lithology, and rock strength. However, further information can be obtained, if quantitative log interpretation is made. To assist in the uptake of quantitative interpretation, we discuss log responses in terms of the mineralogy of the clastic sedimentary rocks frequently found in the Australian black coal mining areas of the Sydney and Bowen Basins. We find that the log responses can be tied to the mineralogy with reasonable confidence. Ambiguities in the interpretation will be better resolved if a full suite of logs is run. A method for checking for internal consistency, by comparing calculated and observed velocities, is also described. A key driver for quantitative interpretation is geotechnical characterisation. We propose a classification system for clastic rocks that takes into consideration physical rock properties that can be inferred from geophysical logs.

• Journal of the Korean Geosynthetics Society
• /
• v.18 no.4
• /
• pp.115-127
• /
• 2019

The low-flow grouting injection technique, the target construction method for this study, is a method of pouring mortar into the ground by non-emission replacement principle, which can be expected to increase the density of the ground, and, in some cases, be used as a base file using the strength of the high injection solids, along with low noise, low pollution, and high durability. To verify that the dynamic characteristics of the ground are improved by the low-flow injection technique, the test work was conducted on the site and physical tests were performed, and the quality of the improvement formed in the ground was verified through the indoor test on the core and core recovery rate was analyzed. The density logs test layer calculated the volume density of the ground layer by using the Compton scattering of gamma-rays, and the sonic logs was tested on the ground around the drill hole using a detector consisting of sonar and receiver devices inside the drill hole. As a result of the measurement of the change in physical properties (density and sonic logs) before and after grouting, both properties were basically increased after infusion of grout agent. However, the variation in density increase was greater than the increase in speed after grouting, and the ground density measurement method was thought to be effective in measuring the fill effect of the filler. Strength and core recovery rates were measured from specimens taken after the age of 28 days, and the results of the test results of the diffusion and strength test of the improved products were verified to satisfy the design criteria, thereby satisfying the seismic performance reinforcement.