• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2008.11a
• /
• pp.108-110
• /
• 2008

다이아몬드마이크로블레이드의 윤활제첨가에 따른 절삭 성능과 수명향상을 위해 절삭에 따른 블레이드의 마모량을 측정시험을 행하였고 블레이드의 절삭성능을 평가할 수 있는 지표인 일정속도로 절삭 중 블레이드의 전력소모량을 측정하였다.

• Tribology and Lubricants
• /
• v.1 no.1
• /
• pp.46-58
• /
• 1985

The basic mechanism of lubrication between the piston ring and the cylinder wall is developed theoretically under the assumption of a reciprocating and dynamically loaded slider-bearing pair of parabolic form and smooth plane. A numerical computation for the prediction in cyclic variations of film thickness, net lubricant flow and frictional behaviour is attempted, and the influenec on the performance characteristics due to the ring height, ring face radius of curvature and the degree of offset, is also examined. The computational procedures develeped for a single ring system are extended and applied further to the complex problem of a ring pack system. It is well known that the ring pressure which is the total load on a ring, can be obtained from either an experimental measurement or a gas flow analysis. In this work, the latter of a gas low analysis method was used to calculate the pressures. It is remarked that the work done was focused on the role of flow continuity and lubricant starvation within the ring pack lubrication.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.19 no.5
• /
• pp.706-712
• /
• 2009

In this paper, a fault diagnosis method is proposed to detect and classifies faults that occur in press process line. An oil level automatic monitoring method is also presented to detect oil level. The FFT(fast fourier transform) frequency analysis and ART2 NN(adaptive resonance theory 2 neural network) with uneven vigilance parameters are used to achieve fault diagnosis in proposing method, and GUI(graphical user interface) program for fault diagnosis and oil level automatic monitoring using LabVIEW is produced and fault diagnosis was done. The experiment results demonstrate the effectiveness of the proposed fault diagnosis method of induction motors and oil level automatic monitor system.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.6
• /
• pp.916-922
• /
• 2001

A mechanical face seal is a tribo-element intended to control leakage of working fluid at the interface between a rotating shaft and its housing. Leakage of working fluid decreases drastically as the clearance of the mating seal faces gets smaller. But the very small seal clearance results in an increased reduction of seal life because of high wear and heat generation. Therefore, in the design of mechanical face seals a compromise between low leakage and acceptable seal life is important, and it presents a difficult and practical design problem. A fluid film or sealing dam geometry of the seal clearance affects seal lubrication performance very much, and thereby it is one of the main design considerations. In this study the Reynolds equation for the sealing dam of mechanical face seals is numerically analyzed, using the Galerkin finite element method, which is readily applied to various seal geometries. Film pressures of the sealing dam are analyzed, including the effects of the seal face coning and tilt. Then, lubrication performances of the seals, such as opening forces, restoring moments, leakage, and dynamic coefficients, are calculated, and they are compared to the results obtained by the narrow seal approximation.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.06a
• /
• pp.219-226
• /
• 2000

Frictional performance of ring pack in internal engine is investigated by varying spatial dimensions of ring pack and operating speed. This investigation is performed with commercial software by Ricardo Consultant Engineers, Inc. which is now in wofdwide use in automobile industries. Among the ring performances, blow-by rate, axial ring motions and frictional behaviors of top and second rings are studies in our work.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.11a
• /
• pp.197-203
• /
• 2001

In this paper, numerical analyses were undertaken to calculate the static and dynamic performances of step-pocket, inward pumping spiral grooved, outward pumping spiral grooved and herringbone grooved bearings. For each bearing, optimal values for various design parameters were obtained to maximize the load capacity and the stiffness and bearing performances were calculated. The optimized performances of these bearings were compared to conclude that the performance of step-pocket bearing is better than the other bearings.

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.1
• /
• pp.12-24
• /
• 2017

The main purpose of this research is for the investigation on the impact of engine oil aging on PM and DPF. It is widely known that lubricant specifications and consumption from an ICE have significantly influenced on the regulated and unregulated harmful emissions as the engine operating conditions. Considering DPF clogging phenomena with lubricant-derived soot/ash components, simulated aging mode for the DPF was newly designed for engine dynamometer testing. PM/ash accumulation cycle were developed in reflecting real-world engine operating conditions for the increment of engine oil consumption and natural DPF regeneration for the ash accumulation. The test duration for DPF aging reached around 100hrs with high- and low-SAPS engine oils, respectively. Using high SAPs engine oil made more PM/ash accumulation compared with low SAPs engine oils and it could accelerate fouling of EGR in engine. Fouling of EGR made effects on more harmful exhaust gases emissions. The test results on engine lubricant under engines operating conditions will deliver for the establishment of regulated and unregulated toxic emissions policy, lubricant quality standard.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.17-18
• /
• 2014

최근 자동차 성능 및 연비향상을 위해서 엔진의 고출력화 및 소형화 경향이 뚜렷해지고 있으며, 이로 인해 엔진내부의 부품이 받는 환경은 더욱 가혹해 지고 있다. 즉, 자동차 엔진 구동부품은 금속간의 접촉가능성이 매우 높은 경계윤활조건에 놓이게 되며, 또한 배기가스 규제로 인한 첨가제를 최소화 하려는 경향에 따라 경계윤활 환경에서 더욱 심한 마모문제에 직면할 것으로 예상되어 내구성 및 내마모성이 높은 코팅기술에 대한 요구가 더욱 증가하고 있다. 본 연구에서는 Zr기지의 비정질 형성능을 갖는 합금계를 이용하여 아르곤 및 질소분위기에서 스퍼터링 함으로써 고경도의 ZrN상과 엔진오일과 반응하여 저마찰 트라이보 필름을 형성시킬 수 있는 금소계 원소가 Tissue phase로 존재하는 질화물 나노박막합성기술을 개발한 후 자동차 구동부품인 벨브트레인계 및 피스톤링/라이너 부품에 적용하여 마찰특성을 평가하였다.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.11a
• /
• pp.347-352
• /
• 2000

Before investigating the performance of NA-Q additive oil, we have studied the properties of the commercial reference oil by using an engine dynamometer. Experimemts were conducted for 300 hours with 2,950rpm and 22kw and every 50 hours the used oil was sampled for analyzing its physical and chemical propreties. The reference oil shows stable but slightly increasing viscosities during the experiment. It has good agreements with the change of its TAN and TBN. Friction coefficients and anti-wear characteristics are compared with its ZDTP depletion factor and the diameters of wear scar. The concentrations of metal particles are analyzed with the results of ICP and spectrometer, However it is found that the concentrations by filtration method shows large difference with those by standard method in spectrometer.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.3
• /
• pp.1664-1670
• /
• 2015

As journal bearing has a sliding motion between the shaft and bearing with lubricating oil, it produces a hydrodynamic lubrication condition. Journal bearing can receive a large force because it takes a distributed load at the large friction face. As the oil groove or oil hole is made in the journal bearing surface for the journal bearing smoothly working under a hydrodynamic lubrication condition, sufficient lubricating oil is supplied through the clearance of journal bearing. The performance of the journal bearing is changed according to the shapes, sizes and positions of an oil groove. In this paper, the flow rate according to the oil groove shapes (triangle, semicircle and rectangle) among the various oil supply conditions was measured. The shape that discharges the highest flow rate was observed and the groove shape of optimal performance for the journal bearing was determined. The results showed that the flow rate increases with decreasing operating temperature, the influence of temperature on the flow rate decreased with increasing rotational speed, and flow rate in the triangular groove shape was greater than in other shapes.