• Journal of Korea Society of Industrial Information Systems
• /
• v.23 no.1
• /
• pp.43-52
• /
• 2018

This paper presents the performance of a Phase Shift Full Bridge (PSFB) converter with inductive load and a new current control scheme to improve dynamic response of output current with various inductive loads. Enhanced dynamic model is used which includes leakage inductance and inductive load. Effect of changing of inductive load was analyzed in detail. Proposed current control scheme is designed based on phase margin specifications. As a result, the proposed current control scheme helps to improve the dynamic response in comparison with the existing current control scheme. The performance of the designed controller is verified by a 500 A PSFB converter. The results will be utilized for high current applications with high inductive load such as superconducting devices.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.9B
• /
• pp.823-833
• /
• 2003

To satisfy the requirements of the real-time Internet services, queue management and scheduling schemes should be enhanced to accommodate the delay and jitter characteristic of them. Although the existing queue management schemes can address the congestion problems of TCP flows, they have some problems in supporting real-time services. That is, they show performance degradation when burst traffics are continuously going into the system after the queue is occupied at a predefined threshold level. In addition, under the congestion state, they show large jitter, which is not a desirable phenomenon for real-time transmissions. To resolve these problems, we propose a SDRED (State Dependent Random Early Detection) and dynamic scheduling scheme that can improve delay and jitter performances by adjusting RED parameters such as ma $x_{th}$ and $w_{q}$ according to the queue status. The SDRED is designed to adapt to the current traffic situation by adjusting the max,$_{th}$ and $w_{q}$ to four different levels. From the simulation results, we show that the SDRED decreases packet delays in a queue and has more stable jitter characteristics than the existing RED, BLUE, ARED and DSRED schemes.mes.mes.

• The Transactions of the Korea Information Processing Society
• /
• v.7 no.8
• /
• pp.2463-2472
• /
• 2000

In this paper, we consider pits and falls of V oIP service scheme over the air link environment. It results that V oIP over packet switching is a more attractive approach in several points. We point out the ffilIior requirements for successful V oIP service over the air. Also, we propose V oIP CP concept for efficient wireless channel utilization. Additionally, we analyze and evaluate the performance. According to the results, It shows that the long cycle VolP vocoder CODEC such as ITU-T G.723 is better than short cycle V oIP vocoder CODEC. In this case, the increase of the simultaneous user of system is almost 60% larger than conventional circuit switching.

• Journal of Bio-Environment Control
• /
• v.11 no.2
• /
• pp.93-100
• /
• 2002

This study was carried out not only to develop CFD model for numerically simulating fog cooling system but also to verify the validity of the developed model by data measured in fag cooling greenhouse. In addition the developed model was applied to investigate the effects of spraying water temperature, spraying water amount, spraying interval and evaporation percentage on the performance of the fog cooling system. According to the simulation results, the temperature differences between the measured and predicted temperatures at each measurement point were $0.1~1.4^{\circ}C$ in case of no shading and $0.2~2.3^{\circ}C$ in close of shading. The humidity differences were 0.3~6.0% and 0.7~10.6%, respectively in the cases of no shading and shading. Because the predicted data showed a good agreement with the measured ones, the developed model is supposed to be able to predict the cooling effect of the fog cooling system. The performance of fog cooling system was greatly influenced by spraying water amount, spraying interval and evaporation percentage, but it was not influenced by spraying water temperature.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.1
• /
• pp.52-60
• /
• 2013

Ejector-diffuser system makes use of high-pressure primary stream to entrain the low-pressure secondary stream through pure shear action between two streams. In general, the flow field in the ejector-diffuser system is highly complicated due to turbulent mixing, compressibility effects. A fatal drawback of the ejector system is in its low efficiency. Many works have been done to improve the performance of the ejector system, but not yet satisfactory. In the present study, a mixing guide vane was installed at the inlet of the secondary stream for the purpose of the performance improvement of the ejector system. A CFD method has been applied to simulate the supersonic flows inside the ejector-diffuser system. The present results obtained were validated with existing experimental data. The mixing guide vane effects are discussed in terms of the entrainment ratio, total pressure loss as well as pressure recovery.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.3
• /
• pp.251-257
• /
• 2012

The flight controller should meet the flying qualities, stability margins, and time response requirement according to the class of a target aircraft or UAV. Classical design process of PID controller is a very time consuming process and needed trial and erros. The best way is to apply the multi-disciplinary optimization algorithm to meet the numerous constraints of controller requirements. This paper presents how multi-objective parameter optimization (CONDUIT) can be used to determine many design parameters of lateral stability and augmentation system for roll and heading controller of the small UAV. To verify the effectiveness of applying the optimization method, designed controller using optimization are compared with the baseline controller that is designed only considering the time responses.

• Journal of Digital Contents Society
• /
• v.15 no.1
• /
• pp.1-9
• /
• 2014

Delay-Tolerant Network (DTN) is an asynchronous networking technology that has been deployed for the networking environment in which steady communication paths are not available, and therefore it stores receiving data in a data storage and forward them only when the communication links are established. DTN can be applied to sensor networks and mobile ad-hoc network (MANET) as well as space communication that supports data transmissions among satellites. In DTN networking environments, it is very important to secure a scheme that has relatively low routing overhead and high reliability, so that it can enhance the overall routing speed and performance. In order for achieving efficient data transmissions among the nodes that have comparatively periodic moving patterns, this paper proposes a time information based DTN routing scheme which is able to predict routing paths. From the simulation results using Omnet++ simulation tools, it has been verified that the proposed time information based DTN routing algorithm shows satisfied levels of routing speed and routing reliability even with lower routing overheads.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.6
• /
• pp.681-691
• /
• 2017

In the clutter environment, it is necessary to update the target tracking filter by detecting the target signal among many measured value data obtained via the radar system, the track does not diverge, and tracking performance is maintained. The method of associating the measurement most relevant to the target track among numerous measurement values is referred to as data association. PSNF and PSNF-m are data association methods of SN-series. In this paper, we provide an IPSNF-m(Integrated Probabilistic Strongest Neighbor Filter-m) algorithm with a track management method based on the track existence probability in PSNF-m algorithm. This algorithm considers not only the presence of the target but also the case where the target is present but not detected. Calculating the probability of each caseenables efficient management. In order to verify the performance of the proposed IPSNF-m, the track existence probability of the IPSNF algorithm applying the track management technique to PSNF, which is known to have similar performance to PSNF-m, is derived. Through simulation in the same environment, we compare and analyze the proposed algorithm with RMSE, Confirmed True Track, and Track Existence Probability that show better performance in terms of track retention and estimation than the existing PSNF-m and IPSNF algorithms.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.10
• /
• pp.4725-4732
• /
• 2012

This paper studies MR16 that can strengthen the strength and make up for the weakness of MR16 by replacing halogen light source using multifaceted Reflector(MR16) with LED light source. To achieve this, developed MR16 for LED applying optical system that four aspheric lens is one sheet. Optical system is designed by optics software and lighting performance of the designed data is predicted lighting simulation program. Also, heatsink's heat radiation analysis program to predict the thermal performance. Finally, optical prototype system based on simulation analysis data is manufactured and the results comparing performance of the developed system and the designed data are follows: Radiation angle was around $50^{\circ}{\sim}60^{\circ}$ in results of simulation analysis and the test of the prototype system. Also, temperature measurement result indicates that the thermal equilibrium is realized after one minute and thirty seconds and heat is generated up $60^{\circ}C$ in all of simulation analysis and the test of the prototype system. Finally, simulation analysis result on light disturbance curve of MR16 is similar to that of performance of the prototype system.

• Journal of Bio-Environment Control
• /
• v.26 no.4
• /
• pp.402-410
• /
• 2017

The effect of the steel pipe member joint on the design performance of a plastic multi-span greenhouse was analysed through the comparing full-scale experiment and numerical analysis. The design performance of the greenhouse is generally evaluated through numerical analysis, but it is rare to consider the characteristics of the connections or joints of the members. In this study, the effect of the column-gutter beam-rafter-wind break wall joint on the design performance of the whole structure of a plastic multi-span greenhouse was analysed. The numerical results with assuming that the member joint are rigid condition were compared with the full-scale load test results using member joints used in the field. The stiffness of the entire structure was compared using the load-displacement relationship and the change of the load sharing ratio that the main members such as column, rafters, and wind break wall was analysed. The results of the load test were about 40% larger than the numerical result and the member stress was more than twice as large as those of the loaded columns. In order to increase the reliability of the design performance of the greenhouse, it is necessary to develop a numerical analysis model which can consider the characteristics of various joints.