• Journal of Korean Society of Forest Science
• /
• v.97 no.1
• /
• pp.61-70
• /
• 2008

This study was conducted to develop a mobile tower-yarder with tractor for agriculture and forestry that is the efficient yarder in steep terrains, thinning operation and small scale logging operation. It was designed and manufactured that the power source of tower-yarder is equiped three hydraulic pump connected to PTO of tractor, and three hydraulic pump is used to operate the four motor for drum, the cylinder for clutch of interlocker, the cylinder for tower expanding and the out-rigger cylinder. It was to adopt the running skyline system and the inter-lock function, and to equip the double capstan drum, the storage drum and the clutch for interlock in the development of tower-yarder. It was to develop the tower-yarder which the winch torque of double-capstan drum, the traction force of double-capstan drum, the number of rotation of double-capstan drum and the line speed is $191kg{\cdot}m$, 1,910 kgf, 220.5 rpm and 138.5 m/min, respectively. And it was known that the optimum flange diameter of the main and haulback storage drum is about 360 mm and about 460 mm in order to storage the main line length of 250m and the haulback line length of 450 m. The carriage was made to adopt the running skyline system and to equip the lock function in order to the convenience of chocking and the fall down preventing of tree. It was provided to develop the wire remote controller for the inter-lock function, the convenience of control and the efficiency of yarding. In development process, this tower-yarder was attached the 3-point linkage hitch equipment and the tire wheel for the traction and moving of tower-yarder. Also, it was equipped that the out-rigger and the guy line in order to raise the safety and efficiency of yarding of tower-yarder.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.473-478
• /
• 2003

This paper presents static and dynamic measurement of the stress and motion characteristics for crawler type excavators. Eight scenarios were prepared for static measurement based on two extreme digging positions, maximum digging reach position and maximum digging force position. The measured items for static motion included stress, cylinder pressure, cylinder stroke and digging force. The measured static stresses showed that asymmetric digging force acting on a bucket induced higher stress level than symmetric one. The measured static pressures and digging forces also agreed with design pressures and design digging forces, respectively. The dynamic measurement was performed for two types of motion, that is, simple reciprocation of each cylinder and actual digging motion. The measured items for dynamic motion were stroke and pressure of each cylinder, stresses on the working device and acceleration on the upper plate of an arm. The measured data showed that the natural frequency of the excavator highly depended on the hydraulic stiffness of cylinders. Digging motion tests revealed that digging motion was closer to static motion rather than dynamic one.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.1
• /
• pp.947-950
• /
• 2005

For revolving and elevating a turret of a tank, we substitute an existing oil pressure system with an electric system using a motor and applied the vector control method to this system. A switching method of an inverter for providing desired sinusoidal current to each phase of a motor, we adopted min-max pulse width modulation method which takes less computation time, rather than space vector pulse width modulation method. We designed a digital filter and applied it to the control system. Developed current controller is verified it's performance through a current control test, speed control test, frequency response and tracking a profile of speed test.

• Journal of the Society of Naval Architects of Korea
• /
• v.35 no.3
• /
• pp.26-37
• /
• 1998

In this study, the motion control techniques allied to the test ship NARAE are summarized and the results of sea trials are resented. NARAE adopted a hybrid hull form with lower hull and submerged foils. This type of ship has a substantial instability in heave, pitch and roll modes at the foil-borne stage due to little restoring force, so an active control is indispensable to keep the stability. 4-hydraulic actuators with servo valves were installed to drive foils, and several sensors were used to measure the motion of the ship. PID controller was adopted as a motion controller, and for the real-time control, Pentium-class industrial PC was used. Sea trials including take-off, landing, and banked turn maneuvering were carried out for a period of over 3 months and quite satisfactory results were obtained.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.17 no.2
• /
• pp.85-91
• /
• 1981

An equation was derived which describes the slip force that occurs at the casting of initial state due to unequilibrium with support bar weight, liquid metal, casting velocity, thickness, control roller, hydraulic motor and etc. The slip force equations are solved on the basis of velocity, gravity and thickness in casting ingot. In this paper the auther assumed that the other mechanisms are normal. The behaviour of slip force in many characteristics is calculated as a function of velocity, gravity and thickness with variation. The conclusion with this phenomena is reached that the present theory realistically predicts the growth of slip force in a flat plate ingot continuous casting machine.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• v.10 no.2
• /
• pp.59-63
• /
• 2005

가. 자율주행 트랙터가 작업하는 동안 작동상태를 효과적으로 모니터링하고 제어할 수 있도록 하기 위해 인터넷을 통한 자율주행 트랙터의 모니터링과 원격제어 기술에 대하여 시험 하였다. 나. 트랙터를 모니터링하고 제어하는 곳과 경작지가 있는 곳을 인터넷으로 연결하고, 운전자가 탑승하지 않은 트랙터는 인터넷을 통해 전달받은 명령을 수행하도록 액튜에이터를 제어하고 제어되는 상황을 경작지에 위치한 카메라가 촬영하여 인터넷을 통하여 원격지의 운전자 쪽으로 전송하도록 시스템을 구성했다. 다. HST 트랙터 조종장치로서 서보제어가 가능한 액튜에이터를 개발 장착하고 제어성능을 시험하였다. 전자유압제어(EHPS)식 조향액튜에이터는 , 조향가능각 100도의 전범위에 조향 제어가 가능했으며 전조향에 필요한 시간은 약 1.6초 정도 였다. 피스톤 펌프의 사판각을 제어하는 전후진 제어기는 리니어 모터 구동식으로 총 제어 변위 50mm를 이동하는데 제어시간이 약 1.2초 소요되었다. 엔진 회전수를 제어하기위한 스로틀 액튜에이터는 리니어 모터 구동식으로 제어변위 30mm에 대해 제어시간이 0.8초 소요되었다. 3점 링크에 부착된 작업기의 위치를 제어하는 리프트 제어기도 리니어모터로 구동하였으며 제어거리 40mm에 대해 제어시간 0.9초정도가 소요되었다 라. 제작된 HST 무인 트랙터를 인터넷과 무선통신 시스템을 이용하여 원격 모니터링과제어 가능성에 대해 시험 했다. 인터넷을 통한 장거리 원격제어 및 모니터링 시험에서 제어신호의 전달지연은 0.3 ${\sim}$ 0.5초정도로 제어신호의 피이드 백을 확인할 때까지는 약1초정도의 대기 시간이 필요한 것으로 나타나 모니터링 및 제어 시스템의 개발 시 이를 고려할 설계가 필요한 것으로 나타났다.된 표층수온 분포값보다 2005년 2월에 관측된 표층수온 분포값이 상대적으로 낮은 분포 특성을 나타내고 있었다. 따라서 인공위성자료를 이용한 황해의 2004년 해황 분석 결과는 이상수온 상승의 원인이 쿠로시오 해류의 변동과 관련성이 높다고 판단되며 이에 대한 지속적인 연구가 현재 진행중에 있다.에 인산염 처리, 여기에 초음파 처리, 마지막 단계로 3분 끓이면 억제율이 68%까지 억제되었다. 이는 단일처리시 전혀 억제를 못하는 처리를 단계별로 한 단계씩 더해가면 allergy 억제효과가 나타난다고 할 수 있겠다. 초음파 처리도 역시 저 allergy 처리 공정에 이용될 수 있는데 이것은 그 처리로 인해 새로운 알러젠이 생성될 수도 있다. 또한 복합처리로 allergy를 감소시키면 연속적이고 동시적으로 하기 때문에 원가를 절감할 수 있다.환경현안에 대한 정치경제적 접근을 외면하지 말고 교과서 저작의 소재로 삼을 수 있어야 하며, 이는 '환경관리주의'와 '녹색소비'에 머물러 있는 '환경 지식교육'과 실천을 한단계 진전시키는 작업으로 이어질 것이다. 이후 10년의 환경교육은 바로 '생태적 합리성'과 '환경정의'라는 두 '화두'에 터하여 세워져야 한다.배액에서 약해를 보였으나, 25% 야자지방산의 경우 50 ${\sim}$ 100배액 어디에서도 액해를 보이지 않았다. 별도로 적용한 시험에서, 토마토의 경우에도 25% 야자지방산 비누 50 ${\sim}$ 100배액 모두 약해를 발생하지 않았으나, 오이에서는 25% 야자지방산 비누 100배액에도 약해를 나타내었다. 12. 이상의 결과, 천연지방산을 이용하여 유기농업에 허용되는 각종의 살충비누를 제조할 수 있었으며, 방제가 조사결과 진딧물, 응애 등 껍질이 연약한

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.10
• /
• pp.928-935
• /
• 2015

This paper presents low temperature structural tests of a UAV wing which has room temperature-curing adhesive bond. The wing structure is made of carbon fiber reinforced composites, and the skins are bonded to the inner structures (such as ribs and spars) using room temperature-curing adhesive bond. Also, to verify damage tolerance design of the wing structure, barely visible impact damages are intentionally created in the critical areas. The attachment fittings of the wing are fixed in a specially designed chamber which can simulate the low temperature environments of the operating altitudes. The test load is applied by hydraulic actuators which are placed outside the chamber. The structural tests consist of strain survey tests and a durability test for 1-life fatigue load spectrum. During the tests, strains of major parts are measured by strain gauges and FBG sensors. The change of the initial impact damages is also monitored using piezoelectric sensors. The 1-life damage tolerance of the composite structure is verified by the structural tests under the simulated environments.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.4
• /
• pp.164-172
• /
• 2020

The fuel oil/heat exchanger installed in military aircraft is a device that cools the lubricant oil supplied to other devices, such as an AMAD, and a hydraulic pump using the low temperature of the fuel is cracked at the AMAD lubricant inlet port. If a crack in the heat exchanger occurs, the lubricant oil supplied to other equipment is not cooled. Therefore, the flight can no longer be performed. In this study, non-destructive inspection and microscopic examination of the fracture surface of the oil port were performed to analyze the crack tendency. The oil pipe connected to the oil port is a titanium pipe, which is fastened with over torque and has been identified as the leading cause of heat exchanger oil port cracks. In addition, it was verified as the main reason for cracking by finite element analysis. The material and diameter of the pipe were changed to improve this defect, and the applied torque was adjusted. In addition, the bending value of the pipe was adjusted to minimize the fatigue accumulation due to pulsating pressure. As a result, no cracks occurred on the heat exchanger via the ground test after the installation of an improved pipe under the same conditions.

• Journal of Advanced Marine Engineering and Technology
• /
• v.41 no.1
• /
• pp.105-110
• /
• 2017

This paper introduces a heave compensation system for offshore crane when it subjected to unexpected disturbances such as ocean waves, tidal currents or winds and their external force. The dynamic model consists of a crane which is considered to behave in the same manner as a rigid body, a hydraulic driven winch, an elastic rope and a payload. To keep the payload from moving upwards and downwards, PD(Proportional-Derivative) control was applied by using linearization. In order to achieve a better performance, the sliding mode control and the nonlinear generalized predictive control algorithm was applied according to the time-delay. As a result, the oscillating amplitude of the payload was reduced by the control algorithm. Considering the time-delay involved in the system to be one second, nonlinear generalized predictive controller with a robust controller was a suitable control algorithm for this heave compensation system because it made the position of te payload reach the desired position with the minimum error. This paper presented a control algorithm using the robust control and its simulation results.

• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.2
• /
• pp.61-71
• /
• 1999

This paper resents a novel cargo system adapted for a sea port subjected to severe time-varying tide. The proposed system can perform loading or unloading by using a sort of hydraulic elevator associated with real-tim position control. As a preliminary phase, a small-sized model of the cargo system is designed and constructed. The model consists of three principal components ; container palette transfer(CPT) car, platform with lifting columns and cargo ship. The platform activated by the electro-rheological(ER) valve-cylinder is actively controlled to track the position of the cargo ship subjected to be varied due to the time-varying tide and wave motion. Following the derivation of the dynamic model for the platform and cargo ship motions, an appropriate control scheme incorporating time sequence and PID(proportional-integral-derivative) controller is formulated and implemented. Both the simulated and the measured control results are presented to demonstrate the effectiveness of the proposed cargo system.