• International Journal of Highway Engineering
• /
• v.9 no.1 s.31
• /
• pp.1-15
• /
• 2007

The objective of this paper is the establishment of finite element analysis frame work for pavement research. Finite element analysis results simulating various loading experiments are verified with sensor measurements obtained from the KHC Test Road. The accuracy of the finite element analysis can be supported by these efforts so that it helps spread out the finite element analysis to pavement research and design processes. The finite element model used in this research is the full 3D nonlinear model including concrete slab, lean concrete base, subbase, shoulder, dowel, and tie-bar. In order to accomplish the accurate verification, the loading condition and the pavement temperature distribution are exactly simulated with field measured data. The curling behavior and the strain distribution are compared with measured responses from the loading tests with a truck and the FWD. Strain and curling predictions from the concrete slab are matched well with measured responses but the strain prediction from the lean concrete base is not matched with measured response. In addition, the magnitude of permanent curling is evaluated with the finite element analysis.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.6
• /
• pp.3950-3960
• /
• 2014

In this study, the drag forces on a submerged square cylinder were analyzed using a three dimensional hydrodynamic model. The numerical results were compared with the experimental results to check the reliability of the numerical simulations, and the characteristics of the drag forces with the relative depths were analyzed by analyzing the pressure acting on the cylinder surface, which are normally difficult to measure experimentally. The numerical results showed that the drag forces acting on a submerged square cylinder originate mainly from the pressure forces, and component of the shear forces decreased with increasing relative depth. The pressure coefficient distributions showed that in the case of a low relative depth, a relatively high pressure was formed in the front of a cylinder, and a relatively low pressure was formed in the rear, which gives a high drag coefficient. In a high relative depth, the pressure in the front decreased and pressure in the rear increased, which is a similar phenomenon to that normally observed in two dimensional square cylinder flow. The effect of the static pressure was analyzed and the surface elevation difference between the front and rear zone of a cylinder has a limited effect on the drag forces. Finally, the numerical results showed that the drag forces acting on a submerged square are dominated by the dynamic pressure formed by three dimensional flow and the distribution of local surface elevation.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.19 no.2
• /
• pp.18-35
• /
• 2020

Many human, roadway, and vehicle factors affect vehicle-pedestrian crashes. Especially, the roadway factors are easily defined and suitable for suggesting countermeasures. The characteristics of the road network are one of the roadway factors. The road network significantly influences behaviors and conflicts of drivers and pedestrians. A metropolitan city such as Seoul contains various types of road networks, and crash prevention strategy considering characteristics of the road network is required. In this study, we analyze the effects of road networks on vehicle-pedestrian crashes. In the study, high order road ratio, intersection ratio, high-low intersection ratio are considered as road network variables. Using Geographically Weighted Poisson Regression, crash frequencies in Dongs of Seoul are analyzed based on the road network variable as well as socioeconomic variables. As a result, Dongs are grouped by coefficient signs, and each group is suggested about improvement directions considering conflict situations.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.19 no.2
• /
• pp.105-112
• /
• 2007

Sediment transport model based on the Lagrangian concept considering the grain size distribution(GSD) was setup and the change of the sediment diffusion range was analysed in the condition of considering and not considering the GSD. The GSD curve is assumed as the Log-normal distribution function in order to consider the GSD with respect to the Lagrangian concept and the random numbers, i.e. sediment particles, are generated based on the distribution function. The sediment particles is assumed as the spherical type and the random numbers based on the sediment weight is converted to the sediment diameters. Sediment transport patterns are analysed by the settling simulation, in which the settling velocity is computed by the van Rijn formulae and the horizontal diffusion coefficient is used as the constant parameter. The diffusion patterns are very similar to the patterns with GSD condition. The diffusion range defined as the range including 90%, 99% sediment weight of the total sediment weight, however, is larger than without considering GSD condition in 90%-option and shorter than with considering GSD condition in 99-option, respectively. The diffusion range is defined as tile p-percentage of the cumulative sediment weight region with reference to the 50% region, 90%- option, 99%-option, respectively.

• The korean journal of orthodontics
• /
• v.31 no.1 s.84
• /
• pp.15-24
• /
• 2001

In order to achieve a desirable tooth movement, it is of great importance to control the M/F ratio and to know the location of the center of resistance. The purpose of this study was to locate the center of resistance and the axis of rotation, and to estimate the stress distribution in the periodontal ligament with experimental model. After preparing a model of an upper canine with a simulated periodontal ligament and alveolar bone, the force and moment were applied. The tooth movement was traced using measuring device with LVDTs(Linear variable differential transformers) that can measure three dimensional tooth movement in real time. The results were as follows. 1. The location of center of resistance by transverse force was $29\%$ of root length measured from alveolar crest to apex regardless of force magnitude. The position of the center of resistance is more coronal than that of two-dimensional model($42\%$). 2. The center of resistance and the axis of rotation coincide when couple moment was applied. 3. As the magnitude of moment increases, tooth tends to extrude irrespective of the direction of the moment. 4. The relationship between location of force and axis of rotation (a x b = $49.6\;mm^2$) was obtained. A tooth movement can be predicted through this formula. 5. The centers of rotation by transverse force were plotted linearly.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2020.06a
• /
• pp.146-146
• /
• 2020

최근 하천의 유사 중 소류사량을 계측하기 위해 사용된 기존의 물리적 소류사 샘플러를 이용한 직접계측방법은 홍수 시에 깊은 수위와 빠른 유속, 계측 절차상의 위험성 때문에 현장관측이 매우 어려운 한계를 극복하기 위해 현업에서는 소류사량을 간접적으로 추정하는 이론식에 의한 방법이 광범위하게 활용되고 있으나 이 방법 또한 추정이론식의 적용지역, 적용방법에 따라 결과가 수십배 이상 큰 차이를 나타나 실제 활용성에 대한 문제점이 있다. 이러한 기존의 소류사량 측정 방법의 문제점을 보완하기 위해 소류사량을 간접계측하는 방법이 활발히 제안되고 있다. 대표적인 방법으로 하상 이동 시 소류사의 충돌음을 음향센서로 계측하여 신호처리를 통해 소류사량을 추정하는 계측기기인 하이드로폰이 있다. 그러나 국외의 소류사량 간접계측 장치는 소류사량의 운송량이 많을 경우 음향신호 중접으로 인해 펄스 수의 감소, 감지 가능한 입경크기의 제한 등의 문제가 있다. 또한 국내의 백무평(2018)이 제안한 소류사 분석 방법인 대역통과방법(B-P Method)는 소류사량 추정에 있어서 기존의 방법과는 달리 주파수 특성을 반영하여 이전 연구들에 비하여 펄스 검출률을 향상시겼지만 이 방법은 극히 낮은 저유속과 작은 입경이라는 실험조건에서 이루어졌다는 제한사항이 있다. 따라서 본 연구는 다양한 입경과 고유속에 대하여 소류사량을 정량화할 수 있는 방법을 제시하기 위해 소류사 입경이 하이드로폰에 충돌할 때 발생하는 단독입자의 충돌음을 계측하기 위한 실외 수로실험장치를 구축하여 계측을 수행하였다. 실험은 현장에서 대표 시료로 분류된 몇 가지 입경에 대해서 유량 변화에 따른 충돌음향과 소류사량 그리고 소류사 입경크기에 따른 하이드로폰에서 인지되는 음향 특성을 계측 및 분석하였다. 연구결과 입경 크기 및 수리조건 변화에 따른 하이드로폰의 충돌음향 특성을 파악하여 단일 입경별 소류사량 추정관계식을 산출하였다. 또한 산출된 추정 관계식의 특성치와 공급 소류사량 간의 관계를 유도해 보았다. 향후 혼합입경에 대한 실험과 추정 관계식 신뢰성 검토 후 추가적으로 다양한 실험조건을 고려하여 실제 하천에 운송되는 소류사량과의 교정관계 확립을 진행한다면 국내 소류사량 데이터 수집을 위한 현장 설치까지 가능할 것으로 사료된다.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.18 no.3
• /
• pp.63-75
• /
• 2015

As forest therapy is getting more attention than ever, it is important to organize time for activity and location based on spatio-temporal distribution of weather condition in forest. This study aimed to analyze precise spatio-temporal distribution of weather condition by installing long-term weather monitoring device in Yonghyun national natural recreation forest and using acquired weather data in order to support forest recreation and therapy activity. First, we statistically compared 4 models of semi-variogram and the results were all similar. We selected and analyzed the circular model for this study because it was presumed to be the best model for this case. We derived 128 results from the circular model and through semi-variogram, we identified seasonal and temporal distributions of temperature and humidity. Then, we used boxplot, made of partial sill level, to identify significant differences in seasonal and temporal distributions. As a result, in spring and early morning, both temperature and humidity showed equalized result. On the other hand, in summer and early afternoon, both temperature and humidity showed uneven result. In spring and early morning, changes in weather condition are shown little from spatial shifting, it is ideal to perform recreational activities and forest therapy but in summer and early afternoon, it is unadvisable to do so as the changes in weather condition could be harmful unless any other means of preparations are made. This study proposes its significance by analyzing seasonal micro-weather of single recreation forest and presenting seasonal and temporal outcomes.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.26 no.3
• /
• pp.131-139
• /
• 2014

Infra-gravity waves (IGWs) with a period of 1~3 minutes are a factor that directly influences the motion analysis of moored ships inside a harbor and longshore sediment transport analysis. If significant levels of IGWs from far seas are transferred to a harbor and amplified, they may cause downtime of large ships and induce economic loss. In this study, transfer characteristics of the IGWs intruding from outside to inside Pohang New Harbor were analyzed using statistical analysis and transfer function of wave data measured at both outside and inside the harbor for around 5 years. Transfer characteristic analysis was limited to events where IGWs had wave heights above 0.1 m. The wave height distribution of inside the harbor was similar to that of outside the harbor, while the wave period variance of the former was larger than that of the latter. The parameters of the transfer function was optimally estimated according to each event. The estimated average RMS error of the wave height inside the harbor was around 0.013 m. The estimated parameters had a strong correlation with the linear combination information of IGW wave height, period, and direction (R = 0.95). The transfer function suggested in this study can quickly and easily estimate information on IGWs inside the harbor using IGW information predicted beforehand, and is expected to reduce damage due to unexpected restrictions on harbor usage.

• Environmental and Resource Economics Review
• /
• v.13 no.2
• /
• pp.219-243
• /
• 2004

Generally, electricity market has monopoly market structure because of need of enormous investment for infrastructure. However, the introduction of competition in network industry as electricity is a tendency of the world with decreasing the effects of economy of scale due to the advancement of technology. Now, electricity industry restructuring is in progress but the competition in electricity retail market is not in force yet in Korea. Whether a effective competition exist or not is very important to policy decision maker who drive restructuring, but there are small numbers of quantitative researches on that. In this study, we estimated the effectiveness of competition in the electricity retail market through switching costs. If switching costs are high, consumers actually can be locked in incumbent firm in spite of introduction of competition. Therefore switching is a critical factor to determine effectiveness of competition and to estimate the size of switching costs quantitatively can proffer the information about whether the competition in the electricity retail market is effective or not in the future. We estimated switching costs using consumer' stated-preference data by conjoint analysis. In according to estimation results, the cost of switching process is not so high, but the relative brand loyalty of an incumbent company is significantly high. And the price is considered as the most important factor choosing an electric service commodity. Based on the empirical results, it is possible to analyze the relationship between suppliers' competitiveness resulted from management efficiency and customers' switching possibilities. The paper therefore provides guidance for suppliers in deciding to enter into retail competition and for policy makers in introducing retail competition. And it has a significance of estimating the switching costs directly.

• The KIPS Transactions:PartD
• /
• v.17D no.2
• /
• pp.157-166
• /
• 2010

More recently, RFID (Radio Frequency Identification) systems have begun to find greater use in various industrial fields. The use of RFID system in these application domains has been promoted by efforts to develop the RFID tags which are low in cost, small in size, and high in performance. The RFID applications enable the real-time capture and update of RFID tag information, while simultaneously allowing business process change through real-time alerting and alarms. These be developed to monitor person or objects with RFID tags in a place and to provide visibility and traceability of the seamless flows of RFID tags. In this time, the RFID readers should be placed in diverse locations, the RFID flows between these readers can be tested based on various scenarios. However, due to the high cost of RFID readers, it may be difficult to prepare the similar environment equipped with RFID read/write devices. In this paper, we propose a simulator to allow RFID application testing without installing physical devices. It can model the RFID deployment environment, place various RFID readers and sensors on this model, and move the RFID tags through the business processes. This simulator can improve the software development productivity by accurately testing RFID middleware and applications. In addition, when data security cannot be ensured by any fault, it can decide where the problem is occurred between RFID hardware and middleware.