• Restorative Dentistry and Endodontics
• /
• v.34 no.5
• /
• pp.450-459
• /
• 2009

The aim of this study was to measure the initial dynamic modulus changes of light cured composites using a custom made rheometer. The custom made rheometer consisted of 3 parts: (1) a measurement unit of parallel plates made of glass rods, (2) an oscillating shear strain generator with a DC motor and a crank mechanism, (3) a stress measurement device using an electromagnetic torque sensor. This instrument could measure a maximum torque of 2Ncm, and the switch of the light-curing unit was synchronized with the rheometer. Six commercial composite resins [Z-100 (Z1), Z-250 (Z2), Z-350 (Z3), DenFil (DF), Tetric Ceram (TC), and Clearfil AP-X (CF)] were investigated. A dynamic oscillating shear test was undertaken with the rheometer. A certain volume ($14.2\;mm^3$) of composite was loaded between the parallel plates, which were made of glass rods (3 mm in diameter). An oscillating shear strain with a frequency of 6 Hz and amplitude of 0.00579 rad was applied to the specimen and the resultant stress was measured. Data acquisition started simultaneously with light curing, and the changes in visco-elasticity of composites were recorded for 10 seconds. The measurements were repeated 5 times for each composite at $25{\pm}0.5^{\circ}C$. Complex shear modulus G*, storage shear modulus G', loss shear modulus G" were calculated from the measured strain-stress curves. Time to reach the complex modulus G* of 10 MPa was determined. The G* and time to reach the G* of 10 MPa of composites were analyzed with One-way ANOVA and Tukey's test ($\alpha$ = 0.05). The results were as follows. 1. The custom made rheometer in this study reliably measured the initial visco-elastic modulus changes of composites during 10 seconds of light curing. 2. In all composites, the development of complex shear modulus G* had a latent period for $1{\sim}2$ seconds immediately after the start of light curing, and then increased rapidly during 10 seconds. 3. In all composites, the storage shear modulus G" increased steeper than the loss shear modulus G" during 10 seconds of light curing. 4. The complex shear modulus of Z1 was the highest, followed by CF, Z2, Z3, TC and DF the lowest. 5. Z1 was the fastest and DF was the slowest in the time to reach the complex shear modulus of 10 MPa.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.3
• /
• pp.65-73
• /
• 2013

Recently the exterior attaching reinforcement method is being often used by using FRP (Fiber Reinforced Polymer) as a method of strengthening concrete structure. this FRP exterior attaching reinforcement method has several advantages like high intensity, stiffness, good durability and easy installment comparing to its weight. but its structure is airtight covered by reinforcement material whose water permeability is low and water can't be discharged, thus it may provoke a damage to the structure after a long while. the main purposes of this study are to develop GFRP reinforcement material which can discharge the surface water properly and to measure its special functions. for this, we have changed the normal reinforcement material to water permeable structure and measured its water permeance modulus by an indoor test which shows the process of water permeance with the parameter of contained GFRP quantity. also tried to verify the measured value of the water permeance modulus in theory by analyzing the numbers on water permeance process. the test result showed that the biggest quantity of water, 0.5129 g/h $m^2$ was discharged when the fiber contained quantity reached at 75% and the tensile strength was also biggest by 476.6MPa at 75%, so it appeared that COSREM GP panel with 75% fiber contained quantity is the best in ventilation and structure.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.1A
• /
• pp.11-18
• /
• 2012

This paper deals with the numerical determination of the stress intensity factors of cracked aluminum plates under the mixed mode of $K_I$ and $K_{II}$ in glass-epoxy fiber reinforced composites. For the stress intensity factors, two different models are reviewed such as VCCT and two-step extension method. The p-convergent partial layerwise model is adopted to determine the fracture parameters in terms of energy release rates and stress intensity factors. The p-convergent approach is based on the concept of subparametric element. In assumed displacement field, strain-displacement relations and 3-D constitutive equations of a layer are obtained by combination of 2-D and 1-D higher-order shape functions. In the elements, Lobatto shape functions and Gauss-Lobatto technique are employed to interpolate displacement fields and to implement numerical quadrature. Using the models and techniques considered, effects of composite laminate configuration according to inclined angles and adhesive properties on the performance of bonded composite patch are investigated. In addition to these, the out-of-plane bending effect has been investigated across the thickness of patch repaired laminate plates due to the change of neutral axis. The present model provides accuracy and simplicity in terms of stress intensity factors, stress distribution, number of degrees of freedom, and energy release rates as compared with previous works in literatures.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.42 no.3
• /
• pp.421-426
• /
• 2013

We evaluated physical properties such as density, compressive characteristics, irrecoverable work, and stress relaxation of red pepper powder with different particle sizes. The particle sizes showed a normal distribution in size, with a particle size of $150{\sim}600{\mu}m$ accounting for 70.95% of the particles in the Hanbando cultivar and 82.21% in the Cheongyang cultivar. Loose bulk density ranged between 0.34 and $0.45g/cm^3$, while tapped bulk density ranged between 0.43 and $0.56g/cm^3$. The Hausner ratio was highest (1.531) at a particle size below $150{\mu}m$ in the Cheongyang cultivar. The compressibility and compression ratios were 0.001351~0.004383 and 1.0062~1.0265, respectively. Irrecoverable work ranged between 69.16% and 90.24%. The $K_2$ value and stress relaxation characteristics were greatest (1.74 and 44.92%, respectively) at particle sizes of $300{\sim}425{\mu}m$ in the Cheongyang cultivar. The dynamic angle of repose was $32.84-49.84^{\circ}$. Overall, particle sizes below $150{\mu}m$ had the highest compactibility, cohesiveness, and transformation.

• Korean Journal of Food Science and Technology
• /
• v.37 no.3
• /
• pp.504-507
• /
• 2005

Trichoderma reesei KCTC 6952 possesses cellulase system consisting of three enzymatic components necessary to synergistically hydrolyze crystalline cellulose, among which ${\beta}$-glucosidase effectively releases glucose from glycoside derivatives. ${\beta}$-Glucosidase of T. reesei KCTC 6952 grown in modified Mandels' medium showed maximum activity(1.33 unit/mL) 4 days after initiation of growth. Optimal reaction conditions of the enzyme were 50 mM sodium acetate (pH 5) at $70^{\circ}C$ for 10 min. Enzymatic activities stabilized below $50^{\circ}C$ at pH range of 4-5. Results show ${\beta}$-glucosidase exerted its catalytic activities at relatively high temperatures and broad pH range.

• Journal of Korean Society of Steel Construction
• /
• v.19 no.6
• /
• pp.559-573
• /
• 2007

Orthotropic steel decks are manufactured by welding thin plates therefore it is inevitable that there are abundant works of welding process. On connection of transverse rib web, crossing point of longitudinal rib, transverse rib and deck plate and cut-out parts of transverse rib are the significant position of stress concentration because of out of plane and oil-canning deformation caused by longitudinal rib distortion with shear force and distortion. At the current research, the crossing point where the orthotropic steel decks's effect of improving fatigue performance are high, not placing scallop and diaphragm which have same plane with transverse rib placed inside of longitudinal rib at the same time, the reduce effects of stress concentration at the cut-out section and the crossing are high. Especially the installation of the diaphragm causing great effects based on research results to stress concentration appearance reduce effects at the cut-out section, putting radius of curvature of the diaphragm's top and bottom as a target, as a result of carrying out the parametric analysis an optimal diaphragm form that has great effects in fatigue performance came to a conclusion. Also based on optimal diaphragm form, an advantage of the diaphragm optimal setting position for improvement of the fatigue performance came to a conclusion.

• Parasites, Hosts and Diseases
• /
• v.22 no.1
• /
• pp.85-95
• /
• 1984

This study was performed to investigate the intestinal parasites (especially cestoda) in the guts of Theragra chalcogramma in Korea. The cestode larvae collected were morphologically observed and measured, and at the same time, microscopical study was done with the section slides of the cestode larvae. They were identified on the basis of the descriptions by Schmidt and Yamaguti. The results obtained in this study are as follows: 1. The cestode larvae were identified as Khawia sinesis, Eulacistorhynchus chiloscyllius, Tentacularia coryphaenga, Pssudonybelinia odontasantha and Nybelinia Zingualis. These are new species reported in Korea. 2. The characteristics of Khawia sinesis are its scolex lacking loculi and broad, fat and fimbriate shape. Its neck is not separated from the body but a little constricted. 3. Eulacistorhynchus chiloscyzzius is characterized by fairly long and acraspedote scolex. The bulbs are long; retractor muscles are attached to bases of the bulbs. The two bothridia are oval or round in shape and lacking posterior notch. The tentacles are long and poeciloacanthus; double chainette present. 4. Tentacularia coryphaenea is characterized by its long craspedote and subcylindrical scolex. The bothridia are separated, without free borders and spinous. The tentacles are short, slender, armed with solid hooks in spirals, similar except the base of tentacle. The tentacle sheaths are not twisted. The bulbs are ellipsoidal. 5. Pseudonybelinia odontacantha is characterized by its craspedote scolex. The tentacles are inserted near anterior margin of bothridia and armed with hooks in spirals ascending left to right. The hooks are similar, throughout tentacle, with feeble curve and provided with a tooth-like protuberance on the ventral side. The bulbs are three times longer than its width. The posterior margins of bothridia have a pair of eversible ciliated pits; or fossettes. 6. Nybelinia lingualis is characterized by its short and craspedote scolex. The bothridia are separated, with free boarders. The tentacles are cylindrical, armed with solid and similar hooks in quincunxes.

• The Journal of Internal Korean Medicine
• /
• v.31 no.3
• /
• pp.675-687
• /
• 2010

Objective : Interaction of warfarin with herbal medicines still remains controversial. The aim of this study was to examine the effect of herbal medicines which contain ginseng on PT INR in patients being treated with warfarin. Method : We studied patients who take herbal medicines which contain ginseng with warfarin during their hospitalization. We retrospectively investigated the effect of herbal medicines which contain ginseng. 10 patients were assigned to receive one of the following adjuncts: Group A (n=4) that received Bojungikkitang-gagam, Group B (n=2) that received Ukgunjatang-gagam, and Group C (n=4) that received Shihogyeji-tang, Gamiondam-tang, Gwininaanshim-tang, and Saengpe-san together. We then investigated changes of PT INR in each group. Result : In group A, there were diminutions of PT INR in 3 cases, and increment in 1 case. In group B, there were increments of PT INR in both cases. In group C, there were increments of PT INR in 3 cases and there was no big change in 1 case. Conclusion : In this study, we found that the interaction of combined herbal medicine is very complicated. So, we must study further more study about interactions of combined herbal medicine on PT INR.

• Korean Journal of Food Science and Technology
• /
• v.36 no.3
• /
• pp.478-483
• /
• 2004

Effects of instant coffee on weight, plasma lipids, leptin levels, and fat cell size in high-fat diet-fed rats were investigated, Twenty-four male Sprague-Dawley rats, fed experimental diet containing 40% total dietary fat and 0, 0.6, 1.2, and 2.4% (w/w) instant coffee for 6 weeks, were divided into four experimental groups (n = 6). Feed efficiency ratio of 0.6% coffee group was higher than control group. Weight gain, organ weights, free fatty acid level, and fat cell size were not significantly different among groups. Triglyceride, total cholesterol, HDL-cholesterol, and leptin levels in plasma were significantly higher in 0.6% coffee group than control group. No significant difference in feed efficiency ratio, triglyceride, and leptin levels were found between control and 2.4% coffee group. These results suggest instant coffee may not have effect on obesity.

• Journal of Korean Society of Steel Construction
• /
• v.27 no.1
• /
• pp.23-30
• /
• 2015

Developed in this study were Octagonal-hollow-section(OHS) struts, whose compressive strengths against flexural and local buckling is higher than H-shape or rectangular-hollow-section(RHS) struts with the same unit weight. OHS members are also advantageous in handling and storing compared to circular hollow sections(CHS). OHS members were fabricated from HR Plates by cold forming and fillet welding. 5 numbers of 20m long OHS struts were assembled, each of which consist of two 9.6m long OHS member and two end connection elements made of cast iron. The compressive strength of the OHS strut was evaluated by comparing the test results, design codes and FEM analysis each other. Test results show that all of the struts have almost same or larger compressive strength than Korean Road Bridge Design Code(KRBDC) (2012). The initial imperfections can be estimated by using measured strains and are turned out to be less than L/450 for all the struts tested. The results of FEM analysis show that the variation of initial imperfection has less effects on the compressive strength for struts with vertical surcharge than for those with self-weight only, while the strength decreases as the initial imperfection increases. As the result of this study, the allowable initial imperfection for 20m long OHS struts is recommended to be less than L/350 on job sites.