• Korean Journal of Food Science and Technology
• /
• v.20 no.2
• /
• pp.272-279
• /
• 1988

Kinetics of ascorbic acid destruction and browning were evaluated by the dynamic test using actual drying data in order to apply in the optimization of food dehydration. Radish was chosen as a test material because it has many typical quality characteristics during drying. Radish was dried in the cabinet dryer with being measured in moisture, food temperature, ascorbic acid and browning. Using moisture and temperature history, proposed kinetic model was integrated and parameters of the model were searched by the iteration scheme to show minimum discrepancy between predicted and experimental data. Ascorbic acid destruction and browning were represented by first and zero order reaction respectively. Arrhenius equation was used to describe temperature dependence. Several mathematical functions of moisture dependence were compared in the model simplicity and residual sum of square. Attained kinetic models were analyzed as functions of temperature and moisture. Rate of ascorbic acid destruction was low at high moisture content, increased with moisture decrease to show a maximum at the moisture of $9{\sim}12g/g$ dry solid, and then decreased up to full dryness. Browning rate increased with moisture decrease to show a sharp maximum at $4{\sim}6g/g$ dry solid and decreased with further moisture decrease.

• Membrane Journal
• /
• v.15 no.4
• /
• pp.310-319
• /
• 2005

This paper describes the preliminary study on the development of multi-stage membrane demonstration plant for removal of carbon dioxide from flue gas stream being emitted from LNG boiler in thermal power generation plant. The prerequisite requirement is to design and develop the membrane process producing a $99\%\;CO_2$ with $90\%$ recovery from LNG flue gas of 1,000 $Nm^3$/day. Asymmetric polyethersulfone hollow fiber membranes and membrane modules developed in this laboratory[1] were used in this study. Using the permeation data for the hollow fiber membranes, modelling on the membrane module and multi-stage membrane process was done to meet the requirement condition of the process design. The effects of the operating pressure of feed and permeate side and feed concentration on $CO_2$ purity and recovery were investigated experimentally with the developed hollow fiber modules. These experimental results matched well with theoretical modelling results.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.15 no.1
• /
• pp.39-50
• /
• 2003

This study aims to figure out water quality impacts due to sudden disturbances of sediments during dike construction in land reclamation for the northern part of the Siwhaho Lake where heavily deteriorated settlements from upstream loadings are outstanding. We exploit a 3-D water quality model CE-QUAL-ICM combined with a hydrodynamic model TIDE3D. Simulations are done accounting water-sediment interaction in a 4-$\sigma$ layers. Long-term simulation for 1-year shows that bottom layers around the disturbance location are only affected and marks very high concentration. Complete vertical mixing appears at least 5km apart to downward due to complex effects of geometry, bathymetry and river inflows. It should be addressed that existing condition of the Siwhaho Lake stands for high concentration of COD and TP in winter and spring due to relatively high incoming loadings, however the effect of sediment disturbances yields reverse phenomena, i.e., impacts of dike construction arise greatly in summer and fall. Refined grid system consisting of 150m${\times}$150m rectangular grid, which is doubled system compared to previous study (Suh et al.,2002), gives affordable results by reducing flux differences through a cell especially in front of gate.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.5
• /
• pp.346-353
• /
• 2016

In the design conditions of some research reactors, the siphon phenomenon can cause continuous efflux of water during pipe rupture. A siphon breaker is a safety device that can prevent water efflux effectively. However, the analysis of the siphon breaking is complicated because many variables must be included in the calculation process. For this reason, a simulation program was developed with a user-friendly GUI to analyze the siphon breaking easily. The program was developed by MFC programming using Visual Studio 2012 in Windows 8. After saving the input parameters from a user, the program proceeds with three steps of calculation using fluid mechanics formulas. Bernoulli's equation is used to calculate the velocity, quantity, water level, undershooting, pressure, loss coefficient, and factors related to the two-phase flow. The Chisholm model is used to predict the results from a real-scale experiment. The simulation results are shown in a graph, through which a user can examine the total breaking situation. It is also possible to save all of the resulting data. The program allows a user to easily confirm the status of the siphon breaking and would be helpful in the design of siphon breakers.

• Journal of Korea Water Resources Association
• /
• v.53 no.8
• /
• pp.597-604
• /
• 2020

Muskingum, a hydrologic channel flood routing, is a method of predicting outflow by using the relationship between inflow, outflow, and storage. As many studies for Muskingum model were suggested, parameters were gradually increased and the calculation process was complicated by many parameters. To solve this problem, an optimization algorithm was applied to the parameter estimation of Muskingum model. This study applied the Advanced Nonlinear Muskingum Model considering continuous flow (ANLMM-L) to Wilson flood data and Sutculer flood data and compared results of the Linear Nonsingum Model incorporating Lateral flow (LMM-L), and Kinematic Wave Model (KWM). The Sum of Squares (SSQ) was used as an index for comparing simulated and observed results. Exponential Bandwidth Harmony Search with Centralized Global Search (EBHS-CGS) was applied to the parameter estimation of ANLMM-L. In Wilson flood data, ANLMM-L showed more accurate results than LMM-L. In the Sutculer flood data, ANLMM-L showed better results than KWM, but SSQ was larger than in the case of Wilson flood data because the flow rate of Sutculer flood data is large. EBHS-CGS could be appplied to be appplicable to various water resources engineering problems as well as Muskingum flood routing in this study.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.273-273
• /
• 2010

고열부하 환경에 노출되는 핵융합로의 플라즈마 대향부품은 주로 낮은 원자번호 물질-열전도가 좋은 물질-구조체의 순으로 다층 구조를 이루고 있으며, 이들 간의 우수한 접합성은 부품의 성능을 좌우하는 핵심 요소이다. 이러한 플라즈마 대향부품의 건전성을 평가하기 위해서는 고열속의 열부하를 반복적으로 인가하는 시험이 요구되며, 이를 위해 본 연구원에서는 KoHLT-1, 2의 시험시설을 운용하고 있다. 본 시설에서는 열부하원으로서 그라파이터 히터를 사용하며, 히터는 두 개의 시험 대상부품 사이에 설치되고, 히터에 고전류를 인가하여 복사열에 의해 시험 부품에 열부하를 가하게 된다. 고열부하 환경에서 열피로 시험을 위해 히터에 인가되는 전류를 시간에 따라 일정한 패턴으로 반복적으로 ON-OFF 하게 된다. 본 논문에서는 이러한 고열부하시험을 수행함에 있어 고려해야 할 여러 가지 요소에 대해 논의하였다. 우선 인가하는 열유속(heat flux) 값은 일차적으로 시험시설의 최대 출력에 의해 좌우되며, 시험대상물의 운전조건 및 열부하 반복횟수에 의해 결정된다. 열부하 반복횟수는 주어진 열유속 값에 대해 total strain이 파단에 이르는 수준에 의해 결정된다. 열부하를 인가하는 시간은 히터에 전류를 인가했을 때 요구되는 온도로 상승하는 데 걸리는 시간과 시험대상물의 온도가 더 이상 증가하지 않는데 걸리는 시간에 의해 좌우된다. 냉각시간은 길수록 시험대상물의 온도가 냉각수의 온도에 접근하게 되나 너무 길어지면 시험시간이 급격히 증가하게 되므로, 온도 감소 곡선을 검토하여 적절한 시간을 정하게 된다. 열유속 측정은 냉각수의 온도 상승값과 유량으로부터 계산하게 되며, 정확한 측정을 위해서는 열부하를 인가하는 시간이 충분히 길어야 한다. 또한 시험대상 부품에서 열부하가 인가되는 면적을 정확히 정의해야 하며, 냉각관로에 열부하가 인가되어서는 않된다. 또한 시험대상부품을 지지하는 지지구조체를 통한 열손실을 최소화해야 정확한 열유속을 측정할 수 있다. 시험대상부품을 설치할 때 히터와의 간격 또한 결정해야 할 중요한 요소이며, 간격이 좁을수록 최대 열유속 값을 증가시킬 수 있으나, 너무 가까운 경우 히터의 열변형에 의한 접촉 및 아크 방전의 가능성이 있으며, 이 경우 히터와 시험대상부품의 손상을 가져오게 된다. 시험대상물이 국제열핵융합로(ITER)의 일차벽과 같이 베릴륨이 포함되어 있는 경우 방전에 의한 손상은 인체에 유해한 오염의 원인이 될 수 있다. 또한 순간적인 방전은 고가의 고전류전원의 고장을 유발할 수도 있다. 열부하 시험 중 시험대상물의 온도를 정확히 측정하는 것은 필수적이며, 온도 변화 곡선으로부터 시험대상물의 건전성 여부를 판단할 수 있다. 이를 위해 변화를 가장 잘 탐지 할 수 있는 위치에 온도 센서를 설치하는 것이 관건이며, 이는 사전 분석을 통해 알 수 있다.

• Water for future
• /
• v.29 no.4
• /
• pp.209-221
• /
• 1996

It may be difficult to make exact estimates of peak discharge or runoff depth of a flood and to establish the proper measurement for the flood protection since water stages or discharges have been rarely measured at small river basins in Korea. Three small catchments in the Su-Young river basin in Pusan were selected for the study areas. Various runoff parameters for the study areas were determined, and runoff analyses were performed using three different runoff models available in literatures; the storage function method, the discrete, linear, input-output model, and the linear reservoir model. The hydrographs calculated by three different methods showed good agreement with the observed flood hydrographs, indicating that the models selected are all capable of sucessfully modeling the flood events for small watersheds. The storage function method gave the best results in spite of its weakness that it could not be applicable to small floods, while the linear reservoir model was found to provide relatively good results with less parameters. The capabilities of simulating flood hydrographs were also evaluated based on the effective rainfall from the storage function parameters, the $\Phi$-index method, and the constant percentage method. For the On-Cheon stream watershed, the storage function parameters provided better estimates of effective rainfall for regenerating flood hydrographs than any others considered in the study. The $\Phi$-index method, however, resulted in better estimates of effective rainfall for the other two study areas.

• Current Research on Agriculture and Life Sciences
• /
• v.4
• /
• pp.70-76
• /
• 1986

The purpose of this study is to offer the basic data of the tidal river development program by grasping the diffusion between the high density-sea water and the low density-fresh water in the tidal river. The tidal range of Hyungsan river which flows at Youngil bay in Pohang was selected to analysis the phenomenon of density current. The results obtained are as follows ; The tide of Youngil bay was one time a day, 0.104m in high tide difference and 0.085m in mean tidy difference. The change of sea level by tide was negligible. The volume of reserved water by sea water was $2,700,000m^3$ and available water of irrigation was $1,200,000m^3$ that salt density is below $750{\mu}{\mho}/cm$ out of total volume. Salt intrusion phenomenon by density current was a little water level change, however, it become a salt wedge type by the much salt invasion during the spring tide and it makes a well-mixed type by the retreating salt wedge during the neap tide. As long as there were some density differences between sea water and fresh water, net upstream flow was existed along the bottom of water way from the estuary to the upstream channel.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2016.05a
• /
• pp.74-74
• /
• 2016

복잡한 지형에서 컴퓨터를 이용한 물리적 기반 수치모의는 합리적인 시간내에 연산을 완료하기 위해 대개 큰 연산장비 들을 요구한다. 더욱이 모의되는 현상이 시간단계마다 갱신되어지는 동역학적 현상에 기반된 비정상상태일 때 연산성능은 고려되어지는 가장 중요한 주제가 될 수 있다. 연산 시간을 줄이기 위한 가장 널리 이용되는 전략중의 하나는 적절한 수의 프로세서를 이용하는 병렬 기법이다. 최근 들어 연산속도를 가속화하기 위해 다수의 코어를 이용한 OpenMP 와 MPI 기법들이 병렬해석기법으로 대두되었고 그래픽 연산장치를 이용한 병렬처리 해석기법도 소개되고 있다. 본 연구에서는 중앙연산장치를 이용한 병렬 해석기법을 이용하여 제내지 침수해석의 적용성을 검토하고 그 결과을 비교하였다. 본 연구를 위해 OpenMP 병렬기법을 이용하여 확산파 침수해석 프로그램의 원시코드를 재작성하여 가상 및 실제 유역에 적용하였다. 해석결과는 분산메모리 병렬해석 기법인 MPI를 도입한 모형의 결과와 비교되었다. OpenMP를 도입한 모형과 MPI를 도입한 경우 유량 및 수심의 경우 오차 허용 한계내에 수렴되어 만족되었으나 그러나 연산 속도의 경우 두 기법간의 자료의 저장 방법 차이로 인해 차이를 나타내었다. 가상 유역에 적용된 결과로 검토된 각 기법의 증속(speedup) 효과는 MPI의 경우 4 코어를 이용하였을 때 최고 2.62 배 정도에 도달하는 것으로 나타났다. OpenMP 를 적용한 경우 2.87 배 정도로 나타나 OpenMP 를 이용하였을 때 증속효과가 조금 더 뛰어났다. 이는 두 기법의 메모리 저장방식의 차이로 인해 자료의 전송량과 전송 시간이 적은 OpenMP 를 도입한 모형에서 MPI 모형 보다 상대적으로 뛰어난 결과를 나타내었다. 실제 유역의 적용을 위해 상대적으로 우수한 증속결과를 나타낸 OpenMP를 도입한 모형을 Malpasset 댐 붕괴 유역에 적용하였다. 적용된 요소의 수는 각각 45254, 11352 개로 비교적 많은 요소를 가진 하류지역에 적용하여 병렬효과를 극대화하고자 하였다. 적용결과 두 경우 모두 병렬 해석 기법을 도입한 모형에서 유속과 침수심 등은 순차적 모형과 동일한 값을 나타내었으나 증속효과로 인한 연산시간은 순차적 모형에서 8.57 배로 나타나 병렬 모형의 상대적으로 빠른 연산속도를 판단할 있었다. 위의 적용결과를 통해 계산 요소들이 많은 2 차원 해석의 경우 기존의 단일 코어를 이용한 순차적 해석은 장시간에 걸치 연산시간으로 인해 작업효율이 낮아지는 결과를 발생시킬 수 있으며 병렬 해석을 도입할 경우 주어진 컴퓨터 자원를 효율적으로 이용가능하여 합리적인 연산시간으로 연산결과를 얻는 것이 가능하여 반복적 통계 기법/Ensemble 해석 등을 이용한 종합적 해석이 좀 더 실용적으로 이루어 질 수 있을 것이라고 판단되었다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2018.05a
• /
• pp.71-71
• /
• 2018

Sea pollution accidents have been occurred due to the increase of marine ship traffic. Oil spill from the hull hole induced by tanker collision results in the huge sea pollution. Proper and prompt reaction on such oil spill disaster is needed to minimize the damage. Thru-hull emergency wood plug is typically used to manually close small holes, while it is required to develop some mechanical devices for closing large holes in the hull due to huge fluid pressure. Accurate estimation of oil discharge and velocity from such holes are important to develop proper device to control hull hole damage. High resolution CFD modeling investigation on the configurations of hull hole of 7.5 m initial depth and 30 cm diameter, which was observed in the oil spill accident of the Hebei Sprit off the west coast of Korea in 2007, has been carried out to compute the oil spill velocity distribution in terms of flow depth. Friction loss due to the viscous flow and the discharge coefficient of crude oil with specific gravity SG = 0.85 and viscosity of $4-12cP(mPa{\cdot}s)$ at the temperature of $20^{\circ}C-100^{\circ}C$ are presented in terms of Reynolds number based on the results of high-resolution CFD modeling.