• Journal of the Korean Society of Marine Environment & Safety
• /
• v.30 no.2
• /
• pp.252-261
• /
• 2024

This research establishes design standards for vortex reduction devices (VRDs) aimed at minimizing underwater radiated noise by mitigating horseshoe vortex (HSV) and root vortex (RV) generated at the junction of appendages and the hull of underwater vehicles. Initial analysis replaced the influence of appendage dimensions and flow velocity with the Reynolds number by verifying the Reynolds similarity of vortex flows. The three-dimensional surfaces of VRDs were parameterized using Bezier curves. Optimal length-to-height ratios were identified by evaluating the vortex reduction performances of VRDs with various dimensions. Ultimately, non-dimensional design standards were derived for VRDs, ensuring effective vortex reduction across any appendage, thereby enhancing stealth performance.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.18 no.4
• /
• pp.352-359
• /
• 2012

An experiment was carried out to figure out the turbulence flow characteristics in the wake of the transom stern's 2-dimensional section by 2-frame grey level cross correlation PIV method at Re= $3.5{\times}10^3$, Re= $7.0{\times}10^3$. The angles of transom stern are $45^{\circ}$(Model "A"), $90^{\circ}$(Model "B") and $135^{\circ}$(Model "C") respectively. The depth of wetted surface is 40mm from free surface. Strong turbulence intensity appears at the interaction between the flow separation of the bottom of a model and the free surface. This study provides statistic flow information such as turbulence intensity, Reynolds stress and turbulence kinetic energy. Model C type (Raked transom) has low Reynolds stress and turbulence kinetic energy.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.6
• /
• pp.8-14
• /
• 2005

Understanding of the flow past a bluff body close to a moving ground is very important in automobile and aeronautical fields because of aerodynamic characteristic and instability induced by unsteady vortex shedding. The passive control method that mounted the vertical and horizontal plates at the lower surface of the cylinder is studied to suppress the unsteady oscillation motion. When the grounds moves, the diminish of the shear layer on the ground promotes the interaction between the lower and the upper separated shear layers of the cylinder, hence vortex shedding occurs at the lower gap height than the stationary ground.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.10
• /
• pp.840-845
• /
• 2012

An ARX(Auto-Regressive eXogenous) modeling technique for vortex dynamics in the BFS(Backward Facing Step) flow field is proposed in this paper. In order for the modeling of the dynamics, the spatial and temporal modes are extracted through POD(Proper Orthogonal Decomposition) analysis. Determining the orders of the inputs and outputs for an ARX structure is carried out by the spectrum analysis and temporal mode analysis, respectively. The order of input delay terms is also determined by the flow velocity. Finally the coefficients of the ARX model are designed by using an artificial neural network.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.8
• /
• pp.12-19
• /
• 2004

Low-speed gas flows around a micro-scale flat plate are investigated using a kinetic theory analysis. The Boltzmann equation simplified by a collision model is solved by means of a finite difference approximation with the Discrete Ordinate method. Calculations are made for flows around a 5% flat plate with a finite length of 20 microns. The results are compared with those from the Information Preservation method and a continuum approach with slip boundary conditions. It is shown that three different approaches predict a similar basic flow patterns, while the results from the present method are more accurate than those from the other two methods in details.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.5
• /
• pp.368-375
• /
• 2018

In the present study, aerodynamic load analysis for a floating off-shore wind turbine was conducted to examine the effect of periodic platform motion in the direction of 6-DOF on rotor aerodynamic performance. Blade-element momentum method(BEM) was used for a numerical simulation, the unsteady airload effects due to the flow separation and the shed wake were considered by adopting a dynamic stall model based on the indicial response method. Rotor induced downwash was estimated using the momentum theory, coupled with empirical corrections for the turbulent wake states. The periodic platform motions including the translational motion in the heave, sway and surge directions and the rotational motion in the roll, pitch and yaw directions were considered, and each platform motion was applied as a sinusoidal function. For the numerical simulation, NREL 5MW reference wind turbine was used as the target wind turbine. The results showed that among the translation modes, the surge motion has the largest influence on changing the rotor airloads, while the effect of pitch motion is predominant for the rotations.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.13 no.3
• /
• pp.372-377
• /
• 2010

The objective of this study is to predict the drag of an axisymmetric underwater vehicle with bluff afterbody using CFD. FLUENT, commercial CFD code, is used to simulate high Reynolds number turbulent flows around the vehicle. The computed drag coefficients are compared to available experimental data at various Reynolds numbers. Four widely used two-equation turbulence models are investigated to evaluate their performance of predicting the anisotropic turbulence in a recirculating flow region, which is caused by flow separation arising from the base of the vehicle. The simulations with Realizable ${\kappa}-{\varepsilon}$ and ${\kappa}-{\omega}$ SST turbulence models predict the anisotropic turbulent flows comparatively well and the drag prediction results with those models show good agreements with the experimental data.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.27 no.3
• /
• pp.107-116
• /
• 1990

The liquid sloshing in an elastic tank is a fluid-structure interaction problem. It requires nonlinear analysis to solve the complicated physics involved in the large interaction of fluid-structure, the variation of dynamic characteristics of structure due to hydrodynamic loading, and the distorsion of fluid flow due to structural vibration. In this paper a Lagrangian FEM is introduced to analyze the liquid sloshing in an elastic tank assuming that the elastic wall is one degree of freedom rigid wall. Numerical integration is performed using an implicit-explicit algorithm, which is formed by mixing the predictor-corrector method and the Runge-Kutta 4th order method. The influence of dynamic characteristics of the sloshing tank on the fluid flow is discussed. The numerical method is also applied for the simulation of the wall generated wave in the tank.

• Journal of the Korean Institute of Gas
• /
• v.20 no.6
• /
• pp.58-64
• /
• 2016

Vibrational characteristics of curved pipe structures are investigated with respect to the change of inside flow velocities. Based upon the Hamilton's principle, the equations of motions are derived, and the finite element equation is constructed to solve the frequency equation for curved pipe structures. When the initial tension is neglected in cured pipes, the natural frequencies are reduced as flow velocity increases, and the rapid decreases of the natural frequencies take place. However, when the initial tension is taken into account, the natural frequencies are not changed with the change of the flow velocity. In free vibrational simulation of pipe systems, it is necessary to calculate the initial force due to the velocity and the pressure of the fluid flow from the equilibrium. The force should be included in the equation of motion of the systems to get more accurate natural frequencies. The mechanical properties like stiffness or the location of pipe support need to be changed to avoid resonance. The natural frequencies are to be isolated from the frequency range of dominant vibration modes. The angles of elbows do not affect the change of the fundamental natural frequency, but affect the change of the third or higher natural frequencies.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1989.11a
• /
• pp.1-15
• /
• 1989

바이오트라이보로지(biotribology)란 생물학(biology)와 마찰학(tribology)의 합성어로서 그리이스어의 $\tau\rhoc\betao\sigma$(마찰하다)가 어원이며, 마찰 마모 윤활의 학술 용어 "tribology"가 영어로 된것은 1966년이다. 이때 마찰학이란 이학 또는 공학현상으로서 문제를 해석하는데 한정하였고 생물에 대한 문제까지 광범위하게 고려하지 못하였다. 1972년 영국 석유학회, 기계학회 그리고 Rheology 학회의 공동개최로 "윤활제의 레올로지" 회의가 열렸다. 거기서 Dowson 교수(기계공학)와 Right 교수(루마치스 의학)의 공동논문 "Bio-Tribology"를 발표해서 처음으로 그 용어를 제안하였다. Dowson 교수가 열거했던 바이오트라이보로지의 대상은 다음과 같다. (1) 기계에 사용되는 윤활제에 대한 미생물의 영향 (2) 인간의치의 마모 (3) 면도칼에 대한 저마찰 보호막의 작용 (4) 인체내의 유체수송(뇨관내의 유동기구, 타액의 운동, 혈액흐름) (5) 모세혈관내에서 적혈구의 운동과 혈장에서 그의 윤활작용 (6) 화상치료시 "정압기체 축수"적 부양 (7) 음식물을 씹을 때 타액의 윤활작용 (8) 관절기능의 윤활학적 연구 (9) 인공골두와 인공관절의 윤활학적 연구8) 관절기능의 윤활학적 연구 (9) 인공골두와 인공관절의 윤활학적 연구