• Journal of the Korean Institute of Gas
• /
• v.19 no.4
• /
• pp.22-28
• /
• 2015

In order to keep the competitiveness of LPG fuel for transportation fuel, the difference in fuel consumption with gasoline and cost for an aftertreatment system should be reduced with continuous development of technology for LPG engine. In the present study, spray-guided type direct injection combustion system, whose configuration is composed of direct injector in the vicinity of spark plug, was employed to realize stable lean combustion. A certain level of nitrogen oxides($NO_x$) emits due to a locally rich mixture regions in the stratified mixture. With the application of EGR system for the reduction of $NO_x$, 15% of $NO_x$ reduction was achieved whereas fuel consumption and hydrocarbon emission increased. By the application of EGR, the combustion speed reduced especially appeared at initial flame development period and peak heat release rates and increasing rates for heat release rate decreased as EGR rate increased due to the dilution effect of intake air.

• The KIPS Transactions:PartD
• /
• v.15D no.1
• /
• pp.61-72
• /
• 2008

One of the most significant tasks of software development project is to know how much it will be the software development cost in the early stage of software development cycle. The software development environment and technology are changing very rapidly. For accuracy, we should apply those to the software cost estimation. And it is important that we select the suitable adjustment factor and the value of a suitable adjustment factor. For that, this paper have applied the method of AHP. And we have also analyzed the sensitivity of the adjustment factor which is influenced by decision metrics. In conclusion, the value of the application type adjustment factor is responded more sensitively to the data complexity and the control complexity than processing complexity. And the value of the language adjustment factor is responded more sensitively to the supplying manpower and the time of the coding than the time of the debugging. In the future, we will research the selection of an additional adjustment factor and a suitable value of the adjustment factor which are influenced by the environment and the technology of the domestic software development. And then, in the language adjustment factor, we will try to calculate the value about the individual programming language.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.8A
• /
• pp.739-752
• /
• 2002

Recently, to utilize the limited bandwidth effectively, the concept of partial response (PR) signaling has widely been adopted in both the high-speed data transmission and high-density digital recording/playback systems such as digital microwave, digital subscriber loops, hard disk drives, digital VCR's and digital versatile recordable disks and so on. This paper is concerned with adaptive equalization of partial response channels particularly for the magnetic recording channels. Specifically we study how the PR channel equalizers work for different choices of desired or reference signals used for adjusting the equalizer weights. In doing so, we consider three different configurations that are actually implemented in the commercial products mentioned above. First of all, we show how to compute the theoretical values of the optimum Wiener solutions derived by minimizing the mean-squared error (MSE) at the equalizer output. Noting that this equalizer MSE measure cannot be used to fairly compare the three configurations, we propose to use the data MSE that is computer just before the final detector for the underlying PR system. We also express the data MSE in terms of the channel impulse response values, source data power and additive noise power, thereby making it possible to compare the performance of the configurations under study. The results of extensive computer simulation indicate that our theoretical derivation is correct with high precision. Comparing the three configurations, it also turns out that one of the three configurations needs to be further improved in performance although it has an apparent advantage over the others in terms of memory size when implemented using RAM's for the decision feedback part.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.78-78
• /
• 2000

다결정 실리콘-게르마늄 (poly-SiGe)은 태양전지 개발에 있어서 중요한 물질이다. 우리는 소량의 Ge(x=0.05)으로부터 다량의 Ge(x=0.67)을 함유한 수소화된 비정질 실리콘-게르마늄 (a-SiGe:H) 박막의 고상결정화 과정을 ESR (electron spin resonance)방법으로 조사해보았다. 먼저 PECVD 방법으로 Corning 1737 glass 위에 a-Si1-xGex:H 박막을 증착시켰다. 증착가스는 SiH4, GeH4 가스를 썼으며, 기판온도는 20$0^{\circ}C$, r.f. 전력은 3W, 증착시 가스압력은 0.6 Torr 정도이었다. 증착된 a-SiGe:H 박막은 $600^{\circ}C$ N2 분위기에서 다시 가열되어 고상결정화 되었고, 결정화 정도는 XRD (111) peak의 세기로부터 구해졌다. ESR 측정은 상온 x-band 영역에서 수행되었다. 측정된 ESR스팩트럼은 두 개의 Gaussian 함수로써 Si dangling-bond와 Ge dangling-bond 신호로 분리되었다. 가열 초기의 a-SiGe:H 박막 결함들의 스핀밀도의 증가는 수소 이탈에 기인하고, 또 고상결정화 과정에서 결정화된 정도와 Ge-db 스핀밀도의 변화는 서로 깊은 상관관계가 있음을 알 수 있었다. 특히 Ge 함유량이 큰 박막 (x=0.21, 0.67)에서 뿐만 아니라 소량의 Ge이 함유된 박막(x=0.05)에서도 Ge dangling-bond가 Si dangliong-bond 보다 고상결정화 과정에서 더 중요한 역할을 한다는 것을 알수 있었다. 또한 초기 열처리시 Si-H, Ge-H 결합에서 H의 이탈로 인하여 나타나는 Si-dangling bond, Ge-dangling bond 스핀밀도의 최대 증가 시간은 x 값에 의존하였는데 이러한 결과는 x값에 의존하는 Si-H, Ge-H 해리에너리지로 설명되어 질 수 있다. 층의 두께가 500 미만인 커패시터의 경우에 TiN과 Si3N4 의 계면에서 형성되는 슬릿형 공동(slit-like void)에 의해 커패시터의 유전특성이 파괴된다는 사실을 알게 되었으며, 이러한 슬릿형 공동은 제조 공정 중 재료에 따른 열팽창 계수와 탄성 계수 등의 차이에 의해 형성된 잔류응력 상태가 유전막을 기준으로 압축응력에서 인장 응력으로 바뀌는 분포에 기인하였다는 사실을 확인하였다.SiO2 막을 약화시켜 절연막의 두께가 두꺼워졌음에도 기존의 SiO2 절연막의 절연 파괴 전압 및 누설 전류오 비교되는 특성을 가졌다. 이중막을 구성하고 있는 안티퓨즈의 ON-저항이 단일막과 비교해 비슷한 것을 볼 수 잇는데, 그 이유는 TiO2에 포함된 Ti가 필라멘트에 포함되어 있어 필라멘트의 저항을 감소시켰기 때문으로 사료된다. 결국 이중막을 구성시 ON-저항 증가에 의한 속도 저하 요인은 없다고 할 수 있다. 5V의 절연파괴 시간을 측정한느 TDDB 테스트 결과 1.1$\times$103 year로 기대수치인 수십 년보다 높아 제안된 안티퓨즈의 신뢰성을 확보 할 수 있었다. 제안된 안티퓨즈의 이중 절연막의 두께는 250 이고 프로그래밍 전압은 9.0V이고, 약 65$\Omega$의 on 저항을 얻을수 있었다.보았다.다.다양한 기능을 가진 신소재 제조에 있다. 또한 경제적인 측면에서도 고부가 가치의 제품 개발에 따른 새로운 수요 창출과 수익률 향상, 기존의 기능성 안료를 나노(nano)화하여 나노 입자를 제조, 기존의 기능성 안료에 대한 비용 절감 효과등을 유도 할 수 있다. 역시 기술적인 측면에서도 특수소재 개발에 있어 최적의 나노 입자 제어기술 개발 및 나노입자를 기능성 소재로 사용하여 새로운 제품의 제조와 고압 기상 분사기술의 최적화에 의한 기능성 나노 입자 제조 기술을 확립하고 2차 오염 발생원인 유기계 항균제를 무기계 항균제로 대체할 수 있다. 이와 더불

• Journal of Wetlands Research
• /
• v.12 no.2
• /
• pp.25-33
• /
• 2010

Three plans(induction of water flow, supply of oxygen into water, control of fish causing resuspension of solids) proposed to improve the pollutant removal efficiency of Sihwa Constructed Wetland(CW) were estimated by considering the their efficiency and application to the wetland. After construction of facility for induction of water flow in lower part(W 122m${\times}$L 103m) of the wetland, the mean removal efficiencies of BOD, SS, TN and TP were in range of 12.8~37.4% and BOD was showing the highest efficiency. This result indicates that water flows is one of very important factors in the pollutant removal of wetland, especially near the outlet of a large scale wetland such as Sihwa CW. Dissolved oxygen(DO) concentrations after operation of two oxygen supply systems such as Air Bubble Diffuser and Surface Aeration System increased 15.5% and 27.2%, respectively. For maintaining effective DO concentration in Sihwa CW, the operation of oxygen supply system may be desirable during midnight to dawn in the location in which DO concentration is not enough, for instance less than 2 mg/L in CW. In experiments of the fish removal from Sihwa CW, the mean turbidity was lower in test site(6.2 NTU) than control site(10.6). The removal efficiency of thurbidity by th fish removal from the wetland was 41.5%. Therefore, a relevant fish management through a periodical monitoring of fish and turbidity is needed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.686-686
• /
• 2013

Automotive turbochargers have become common in gasoline engines as well as diesel engines. They are excellent devices to effectively increase fuel efficiency and power of the engines, but they unfortunately cause several noise problems. The noises are classified into mechanical noises induced from movement of a rotating shaft and aerodynamic noises by air flow in turbochargers. In addition to, there is a mechanical noise caused from movement of an actuator, electronically controlling a wastegate valve. It is called as valve rattle noise. The actuator is connected to a valve through a linkage. The noise occurs only if the valve is open, where the linkage is freely contact to neighbor structures without being constrained by any external forces. This condition allows impacts by the pulsation of exhaust gas, and the vibration from the impacts spreads out through turbine housing, causing the rattle noise. The noise is not in mechanical operating wastegate turbochargers because the linkage of an actuator is strongly connected by actuating force. For the electronic wastegate turbocharger, this paper proposed a test device to show the noise generating mechanism with a small vibration motor having an unbalanced shaft. It also shows how to reduce the noise - reduction of linkage clearances, inserting wave washers into a connection, and applying loose fitting in bushing embracing a valve lever to turbine housing.

• Journal of Life Science
• /
• v.26 no.7
• /
• pp.868-874
• /
• 2016

Receptor-interacting protein kinase 1 (RIPK1) and RIPK3 are members of the serine or threonine protein kinase superfamily that phosphorylates the hydroxyl group of serine or threonine through the highly conserved kinase region. The RIPK family plays a crucial role not only in inflammation and innate immunity, but also in mediating programmed cell death, such as apoptosis and necroptosis. The interaction between RIPK1 and other TNFR1-related proteins has been shown to assemble a signaling complex I that controls activation of the pro-survival transcription factor NF-κB upon binding of cytokines to TNF receptor 1 (TNFR1). Moreover, RIPK1 and RIPK3 interact through their RIP homotypic interaction motifs (RHIMs) to mediate programmed necrosis, which has long been considered an accidental and uncontrolled cell death form with morphological characteristics differing from those of apoptosis. Highly conserved sequences of RHIM in RIPK1 and RIPK3 were shown to regulate their binary interaction, leading to assembly of a cytosolic amyloid complex termed the “necrosome”. The necrosome also contains mixed lineage kinase domain-like protein (MLKL), which has been found recently to be a substrate of RIPK3 to mediate downstream signaling. This review provides an overview of the functional and physiological characteristics of RIPKs and MLKL in TNF signaling.

• Korean Journal of Ecology and Environment
• /
• v.47 no.spc
• /
• pp.1-9
• /
• 2014

Lake Suwa is a natural lake which is well-known for sightseeing and fisheries. It had suffered severe eutrophication during 1960s and 1970s with the occurrence of cyanobacterial blooms and the extinction of some benthic animals. Since 1980 water quality has been improved due to efforts of local government, scientists, and citizens. Of various methods that were attempted to improve the water quality of Lake Suwa biological methods received much attention, because it can improve the lake ecosystem integrity and fisheries in addition to the water quality. The aim of this paper is to introduce the biological methods for water quality improvement that had been employed in Lake Suwa, Japan, and their contribution to the economic benefit of local residents. Until now a significant restoration of water quality has been achieved, but there are insufficient recovery of the sediment and biota due to anoxic hypolimnion of the lake. This study proposed suspended cage culture of bivalves as a feasible method of water quality improvement. Increased grazing by bivalves will contribute to the improvement of water quality and fisheries production, which will contribute both to the ecological restoration and economy of local residents.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.4
• /
• pp.428-437
• /
• 2017

Recently, local government has established a development strategy which takes into account the quality of each area, in order to solve the problems posed by poor development, hindrance of the urban landscape, the limits imposed by relevant laws, etc. However, the number of floors is an important factor which determines the urban landscape, planning density and quality of the external space. This planning factor has a very different effect according to the terrestrial circumstances, number of households, underparking ratio, green space ratio and floor area ratio. Therefore, in this study, a case analysis and case study are conducted and the correlation between each index is clarified. The conclusions of this study are follows. Firstly, flexibility should be ensured by taking into consideration the density indicators, average number of floors, and residential environmental performance measures in related laws and systems. Secondly, it is necessary to develop a wide-area planning method that extends the planning concept from the beginning of planning to neighboring blocks or cities. Thirdly, deregulation measures should be implemented, such as establishing specialized strategies for each region, and regulatory measures for encouraging different types of development.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2003.05a
• /
• pp.14-14
• /
• 2003

Silicon carbide (SiC)는 높은 power 영역과 높은 온도영역에서도 작동 가능한 우수한 반도체 물질이다. 또한 우수한 열적 화학적, 안정성을 가지고 있어 가흑한 조건에서의 소자로써도 사용 가능하다. 현재 SiC 적용분야로는 우수한 전기적, 기계적 성질을 이용한 미세소자(MEMS)와 GaN 와 거의 유사한 격자상수를 가지는 것을 이용한 GaN epitaxial 성장의 기판으로도 사용되어진다. 그러나 SiC 는 기존의 습식식각 용매에 대해 화학적 안정성을 가지고 있기 때문에 전자소자의 제작에 있어서 플라즈마를 이용한 건식식각의 중요성이 대두되어지고 있다. 소자제작에 있어 이러한 건식식각시 식각 단면의 제어, 이온에 의한 낮은 손상 정도, 매끄러운 식각 표면, 그리고 고속의 식각 속도둥이 요구되어진다. 본 실험에서는 식각 속도의 증가와 수직한 식각 단면둥을 획득하기 위하여 SF6 플라즈마에서 Source power, dc bias voltage, 그리고 외부에서 인가되는 자속의 세기를 변화시쳐가며 식각 속도, 식각 마스크와의 식각 션택비, 식각 단면둥과 같은 SiC 의 식각 특성을 관찰하였다. 식각 후 식각 단면은 주사전자 현미경(SEM)을 통해 관찰하였다. 본 실험에서의 가장 높은 식각 속도는 분당 1850n 로써 이때의 공정조건은 1400W 의 inductive power, -600V 의 dc bias voltage, 20G 의 외부자속 세기이었다. 또한, 높은 inductive power 조건과 낮은 dc bias voltage 조건에서 Cu는 $SF_6$ 플라즈마 내에서 식각부산물의 증착으로 인해 SiC 와 무한대의 식각선택비를 보였다. 이러한 Cu 마스크를 사용한 SiC 의 식각에서는 식각 후 수직한 식각 단변을 관찰할 수 있었다. 것올 알 수 있다. 따라서, 기존의 pve 보다 세라믹 기판의 경우가 수분 흡수율이 높아 더 오랫동안 전류를 흐르게 하여 방식성이 개선된 것으로 판단된다.을 통해 경도가 증가한 시편의 경우 석출상의 크기가 5nm 이하로 매우 작고 대체로 기지와 연속적인 계면을 형성하나, 열처리가 진행될수록 석 출상의 크기가 커지고 임계크기 이상에 이르면 연속적인 계면은 거의 발견되지 않고, 대부 분 불연속적이고 확연한 계면을 형성함을 관찰 할 수 있었다. 알루미나(${\alpha}-Al_2O_3$) 기판 위에 증착한 $(Ti_{1-x}AI_{x})N$ 피막은 마찬가지로 (200) 우선 방위를 나타내었으나, 그 입자의 크기가 수십 nm로 고속도강위에 증착한 피막에 비해 상당히 크게 형성되었다. 또한 열처리 후에 AIN의 석출이 진행됨에도 불구하고 경도 증가는 나타나지 않고, 열처리가 진행됨에 따라 경도가 감소하는 양상만을 나타내었다. 결국 $(Ti_{1-x}AI_{x})N$ 피막이 열처리 전후에 보아는 기계적 특성의 변화 양상은 열역학적으로 안정한 Wurzite-AlN의 석출에 따른 것으로 AlN 석출상의 크기에 의존하며, 또한 이러한 영향은 $(Ti_{1-x}AI_{x})N$ 피막에 존재하는 AI의 함량이 높고, 초기에 증착된 막의 업자 크기가 작을 수록 클 것으로 여겨진다. 그리고 환경의 의미의 차이에 따라 경관의 미학적 평가가 달라진 것으로 나타났다.corner$적 의도에 의한 경관구성의 일면을 확인할수 있지만 엄밀히 생각하여 보면 이러한 예의 경우도 최락의 총체적인 외형은 마찬가지로 $\ulcorner$순응$\lrcorner$의 범위를 벗어나지 않는다. 그렇기 때문에