• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.1
• /
• pp.70-76
• /
• 2000

This paper describes a one-chip micom controller and phase angle control method for self-starting and energy saving of single-phase induction motor. The proposed method is based on the optimal efficiency control which is running by variable phase angle of main winding current such as to maintain the maximum efficiency characteristics of the motor, in voltage control with TRIAC. Experiments are focused on a capacitor starting single-phase induction motor. The optimal energy saving by variable phase angle control are verified by experimental results. Also, auxiliary winding was controlled by electronic starting switch.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.6
• /
• pp.396-401
• /
• 2004

Single phase induction motor(SPIM) is one of the most widely used type of low power AC motors in the world, especially for domestic or commercial applications where a three phase power supply is not available. Single phase induction motors have no starting torque their own. So there are several ways of starting single phase induction motors. The most common type is the starting capacitor installed in series with the auxiliary winding to increase the starting torque. In the conventional systems, this function is conducted by a centrifugal switch. But the mechanical centrifugal switch has many problems such as switch malfunction. This paper presents the auxiliary winding control using digital universal starting switch to overcome these shortcomings of centrifugal switch.

• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.2129-2131
• /
• 2001

Induction motor has been using for industrial field. Up to the present time, the PID controller has been used to operate this system. However, it is very difficult to achieve an optimal PID gain without any experience, since the gain of the PID controller has to be manually tuned by trial and error procedures. This paper focuses on the fuzzy control for optimal control of the induction motor in plant. In order to attain optimal control, flux, torque and speed controller has been used and an fuzzy logic based controller has been applied to this system. The results of the fuzzy are compared with the PID controller tuned by the Ziegler-Nickels method, through various simulation based on the various disturbance and step response. The simulation results of the fuzzy control represent a more satisfactory response than those of the conventional controllers.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2005.11a
• /
• pp.399-403
• /
• 2005

In this paper, we analyze on the effect of RC filter to mitigate transient overvoltage on the high voltage induction motor fed by H-bridge cascaded 7-level inverter. The switching surge voltage becomes the major cause to occur the insulation failure by serious voltage stress in the stator winding of high voltage induction motor. The effect of switching surge appears more serious in high voltage induction motor than low voltage induction motor. Consequently, we demonstrated that the RC filter connected to the motor terminals greatly reduces the transient voltage stress md ringing. The results of simulation show the suppression of transient overvoltage at the motor end of a long cable. using EMTP

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 1999.11a
• /
• pp.482-485
• /
• 1999

This paper proposes a remote supervisory controlling system of air compressor that is controlled by 80196KC microprocessor. In proposed monitoring system, air compressor located in long distance can be controlled In any condition by RS-232 serial communication. Change of data and abnormal signal of it can be also obtained. The validity of the proposed monitoring system is verified through digital simulations and experiments for air compressor driven by induction motor.

• 전기의세계
• /
• v.16 no.1
• /
• pp.1-2
• /
• 1967

The development of the frequency converter using semiconductor enables to easily control the speed of alternating current machineries. In such case, it is desired to observe how several characteristics are changed, such as primary current, power factor, torque, secondary output, efficiency and transient performance. In this paper, the above characteristics are investigated by means of computational method from various constants relating to the motor which is designed in rated frequency 60 cycles. Transient fluctuations in motor speed are also observed with graphical method. These have been validated by the experimental results. When the frequency is to be varied in order to control the speed, it is seen that some of characteristics are getting better and others worse contrarily. The above characteristics may be applied to the optimum electrical, mechanical design of the motor which puts emphases on speed control.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.920-922
• /
• 2004

This paper presents a speed control system for a linear induction motor(LIM) with cage-type secondary using direct thrust control(DTC). The actual speed of the LIM is detected by the linear scale with the resolution of $100{\mu}m$. Thrust correction coefficient due to the end effect of the LIM is utilized in estimating actual thrust. As a result, responses of the thrust, current, speed, and flux are shown.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.945-947
• /
• 2003

Various kinds of practical machines using single phase induction motor(SPIM) are necessary to control speed and torque. In particular, capacitor-run type SPIM has constitutional characteristics, the motor torque is changed by auxiliary capacitance variation. In this study, we manifest equivalent model having more simplicity, and study the relation between torque and capacitance value of SPIM. And analyze Magnetic vibration for FEM(Finite Element Method) simulation. Also, We design the experimental controller which is able to speed control accurately by phase angle control of AC input voltage. Through the simulation and experimental results, we confirmed validity of this study.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.53 no.3
• /
• pp.145-153
• /
• 2004

A nonlinear adaptive speed observer is designed for the sensorless control of induction motors. In order to design the speed observer, the measurements of the stator currents and the estimates of the rotor fluxes are used. The sliding mode cascade observer is designed to estimate the time derivatives of the stator currents. The open-loop observer is designed to estimate the rotor fluxes and its time derivatives using the stator current derivatives. The adaptive observer is also designed to estimate the rotor resistance. Sequentially, the rotor speed is calculated using these estimated values. It is shown that the estimation errors of the corresponding states and the parameters converge to the specified residual set. It is also shown that the speed controller using these estimates is performed well. The simulation examples are represented to investigate the validity of the proposed observers for the sensorless control of induction motors.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.9
• /
• pp.442-447
• /
• 2003

Motors with HTS wires or bulks have been developing recently. Those are large synchronous motor with HTS wires at the field winding in the rotor, hysteresis and reluctance motors with HTS bulk in the rotor. This paper presents the fabrication and test results of an HTS induction motor. Conventional end rings and short bars were replaced with HTS wires in the motor. Stator of the conventional induction motor was used as the stator of the HTS motor. Rated capacity and rpm at full rotor of the conventional motor were 0.75[kW] and 1,710[rpm]. Two, HTS wires are used in parallel to make the end rings and bars. The critical current of the BSCCO-2223 HTS wire which was used in the bars and end rings were 115[A]. Electrodynamometer was coupled directly to the shaft of the rotor with HTS wires.