• Journal of Bio-Environment Control
• /
• v.28 no.4
• /
• pp.279-285
• /
• 2019

To estimate daily canopy photosynthesis, accurate estimation of canopy light interception according to a daily solar position is needed. However, this process needs a lot of cost, time, manpower, and difficulty when measuring manually. Various modeling approaches have been applied so far, but it was difficult to accurately estimate light interception by conventional methods. The objective of this study is to estimate the spatial distributions of light interception and photosynthetic rate of paprika with time by using 3D-scanned plant models and optical simulation. Structural models of greenhouse paprika were constructed with a portable 3D scanner. To investigate the change in canopy light interception by surrounding plants, the 3D paprika models were arranged at $1{\times}1$ and $9{\times}9$ isotropic forms with a distance of 60 cm between plants. The light interception was obtained by optical simulation, and the photosynthetic rate was calculated by a rectangular hyperbola model. The spatial distributions of canopy light interception of the 3D paprika model showed different patterns with solar altitude at 9:00, 12:00, and 15:00. The total canopy light interception decreased with an increase of surrounding plants like an arrangement of $9{\times}9$, and the decreasing rate was lowest at 12:00. The canopy photosynthetic rate showed a similar tendency with the canopy light interception, but its decreasing rate was lower than that of the light interception due to the saturation of photosynthetic rate of upper leaves of the plants. In this study, by using the 3D-scanned plant model and optical simulation, it was possible to analyze the light interception and photosynthesis of plant canopy under various conditions, and it can be an effective way to estimate accurate light interception and photosynthesis of plants.

• Geophysics and Geophysical Exploration
• /
• v.1 no.1
• /
• pp.25-30
• /
• 1998

Time-lapse crosswell seismic data, recorded before and after the cavity filling, showed that the filling increased the velocity at a known cavity zone in an old mine site in Inchon area. The seismic response depicted on the tomogram and in conjunction with the geologic data from drillings imply that the size of the cavity may be either small or filled by debris. In this study, I attempted to evaluate the filling effect by analyzing velocity measured from the time-lapse tomograms. The data acquired by a downhole airgun and 24-channel hydrophone system revealed that there exists measurable amounts of source statics. I presented a methodology to estimate the source statics. The procedure for this method is: 1) examine the source firing-time for each source, and remove the effect of irregular firing time, and 2) estimate the residual statics caused by inaccurate source positioning. This proposed multi-step inversion may reduce high frequency numerical noise and enhance the resolution at the zone of interest. The multi-step inversion with different starting models successfully shows the subtle velocity changes at the small cavity zone. The inversion procedure is: 1) conduct an inversion using regular sized cells, and generate an image of gross velocity structure by applying a 2-D median filter on the resulting tomogram, and 2) construct the starting velocity model by modifying the final velocity model from the first phase. The model was modified so that the zone of interest consists of small-sized grids. The final velocity model developed from the baseline survey was as a starting velocity model on the monitor inversion. Since we expected a velocity change only in the cavity zone, in the monitor inversion, we can significantly reduce the number of model parameters by fixing the model out-side the cavity zone equal to the baseline model.

• Geophysics and Geophysical Exploration
• /
• v.23 no.1
• /
• pp.22-37
• /
• 2020

We analyze the comprehensive three-dimensional (3D) magnetic structure characteristics from the seafloor to the deep layer of the Tofua Arc (TA) 12 seamount in the Tonga Arc, Southwestern Pacific, using bathymetric and geomagnetic data, and magnetization vector inversion (MVI) results. The seafloor features surrounding TA 12 highlight a NW-SE-oriented elliptical caldera at the summit of the seamount, two small cones in the depressed area. A large-scale sea valley is present on the western flank of the seamount, extending from these caldera cones to the southwestern base of the seamount. TA 12 seamount exhibits a low magnetic anomaly in the caldera depression, whereas a high magnetic anomaly is observed surrounding the low magnetic anomaly across the caldera summit. It is therefore presumed that there may be a strong magnetic material distribution or magma intrusion in the caldera. The 3D MVI results show that the high anomaly zones are mainly present in the surrounding slopes of the seamount from the seafloor to the -3,000 m (below the seafloor) level, with the magnetic susceptibility intensity increasing as the seafloor level increases at the caldera depression. However, small high anomaly zones are present across the study area near the seafloor level. Therefore, we expect that the magma ascent in TA 12 seamount migrated from the flanks to the depression area. Furthermore, we assume that the complex magnetic distribution near the seafloor is due to the remnant magnetization.

• Korean Journal of Plant Resources
• /
• v.13 no.3
• /
• pp.227-242
• /
• 2000

Site characteristics, vegetation structure and dynamics of Kalopanax septemlobus forests in Mt. Heungjeong, Mt. Balwang and Mt. Gariwang were studied to provide the information need for national resources conservation and restoration of K. septemlobus forest in Gangwon-do of Korea. The K. septemlobus forests were distributed at 780m to 1,300m in altitude, steep slope, ridges-slope areas with facing northeast to northwest in good nutrition area. The annual diameter growth of those trees ranged 1.60mm to 2.41mm. Forty-three plots(20$\times$20m) were set up at three natural population of Kalopanax septemlobus forest and TWINSPAN method was used for vegetation structure analysis. The result of TWINSPAN ordination show that geographical features played a role in determining community types in the study areas. Community type of the study areas classified into three groups by TWINSPAN; K. septemlobus-Quercux mongolica- Acer mono community(Mt. Balwang), K. septemlobus-Q. mongolica- Tilia amurensis community(Mt. Heungjeong), K. septemlobus-Betula costata-Q. mongolica community(Mt. Gariwang). In most of the K. septemlobus forests, major woody species appeared predominantly were Q. mongolica, T. amurensis, Acer pseudo-sieboldianum, Lindera obtusiloba, A. mono, Magnolia sieboldii, Ulmus davidiana var. japonica. And also, Those species were surveyed in all the areas. Species diversity(H') of investigated areas ranged 0.3124~0.13992 and this value relatively higher than that of other forests with similar site. The range of similarity indices between surveyed areas was 64.1~64.54%. The distribution pattern of Morista's index show that Kalopanax septemlobus distributed randomly in tree and concentrated a few sample plots in subtree layer and shurb layer. K. septemlobus occupied 37.1~58.8% of tree layer story, 8.4~17.6% of subtree layer, 0~0.38% of shurb layer each surveyed area. The association analysis showed that Kalopanax septemlobus positively associated with Betula ermani, Deutzia glabrata, Carpinus cordata, Fraxinus mandshurica and negatively associated with Symplocos chinensis var. pilosa, Styrax obassia, Acer mono, Euonymus macroptera, Ulmus davidiana var. japonica. According to the diameter distribution of Kalopanax septemlobus community, the community of Mt. Gariwang will gradually decline and replaced by Quercus community. The communities of Mt. Heungjeong and Mt. Balwang has its seedlings and saplings, so it may be sustained.

• Korean Journal of Soil Science and Fertilizer
• /
• v.34 no.1
• /
• pp.33-41
• /
• 2001

Enormous volumes of mining wastes from the abandoned and closed mines are disposed without a proper treatment in the upper Okdong River basin at Southeastern part of Kangwon Province. Erosion of these wastes contaminates soil, surface water, and sediments with heavy metals. Objectives of this research were to fractionate heavy metals in the mine tailing stored in the Sangdong Tungsten tailing dams and to assess the potential pollution index of each metal fraction. Tailing samples were collected from tailing dams at different depth and analyzed for physical and chemical properties. pH of tailings ranged from 7.3 to 7.9. Contents of total N and organic matter were in the ranges of 3.2~5.5%, and 1.3~9.1%, respectively. Heavy metals in the tailings were higher in the newly constructed tailing dam than those in the old dam. Total concentrations of metals in the tailings were in the orders of Zn > Cu > Pb > Ni > Cd, exceeded the corrective action level of the Soil Environment Conservation Law and higher than the natural abundance levels reported from uncontaminated soils. Relative distribution of heavy metal fractions was residual > organic > reducible > carbonate > adsorbed, reversing the degree of metal bioavailability. Mobile fractions of metals were relatively small compared to the total concentrations. Distribution of metals in the tailing dam profiles was metal specific. Concentrations of Cu at the surface of tailing dams were higher than those at the bottom. Pollution index (PI) values of each fraction of metals were ranged from 4.27 to 8.51 based on total concentrations. PI values of mobile fractions were lower than those of immobile fractions. Results on metal fractions and PI values of the tailing samples indicate that tailing samples were contaminated with heavy metals and had potential to cause a detrimental effects on soil and water environment in the lower part of the stream. A prompt countermeasure to prevent surface of tailings in the dams from water and wind erosions is urgently needed.

• Korean Journal of Soil Science and Fertilizer
• /
• v.33 no.3
• /
• pp.139-144
• /
• 2000

This study was conducted to obtain the basic information to increase the practical use of soil survey data through the subdividing of valley shapes with soil sequences due to different parent rocks, and to study the relationship between the valley shapes and parent rock. The various rocks such as sedimentary(gray shale and sand stone) and igneous rocks(granite, granite gneiss and andesite porphyry) which are the major parent rocks in Yeongnam area were investigated. The characteristics of valleys formed and the kinds of soils derived from different rocks were analysed by using aerial photographs and topographical maps scaled 1:5,000. The rill density in igneous rock area was as high as 40. But the rill bifurcation ratio of first order stream was higher in the sedimentary than the igneous rocks except granite area. The mean slope of valleys in igneous areas was about 8%, which was higher than that of the sedimentary areas. The variability of valley width in the complexly metamorphosed rock, such as granite gneiss, and andesite porphyry, was greater than in sedimentary and in granite rocks. Based on the variability of valley widths and valley slopes, it was possible to classify the valleys into two types. The "Uterus-shaped valleys" had wide variability of valley width and were located in the areas of granite gneiss and andesite porphry rocks. while the "Roots-shaped valleys" had narrow variability of valley width and were located in the sedimentary areas. "Uterus-shaped valleys" were typified by having land forms of mountain foot slopes and alluvial fans, and the soil drainage sequences also had complexities. So that, we concluded that the variability of valley width and valley slopes was associated with kinds of parent rocks and metamorphism which influences soil sequence and characteristics.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.6
• /
• pp.954-961
• /
• 2010

Ground-based remote sensing can be used as one of the non-destructive, fast, and real-time diagnostic tools for quantifying yield, biomass, and nitrogen (N) stress during growing season. This study was conducted to assess biomass and nitrogen (N) status of paddy rice (Oryza sativa L.) plants under N stress using passive and active ground-based remote sensors. Nitrogen application rates were 0, 70, 100, and 130 kg N $ha^{-1}$. At each growth stage, reflectance indices measured with active sensor showed higher correlation with DW, N uptake and N concentration than those with the passive sensor. NIR/Red and NIR/Amber indices measured with Crop Circle active sensors generally had a better correlation with dry weight (DW), N uptake and N content than vegetation indices from Crop Circle passive sensor and NDVIs from active sensors. Especially NIR/Red and NIR/amber ratios at the panicle initiation stage were most closely correlated with DW, N content, and N uptake. Rice grain yield, DW, N content and N uptake at harvest were highly positively correlated with canopy reflectance indices measured with active sensors at all sampling dates. N application rate explains about 91~92% of the variability in the SI calculated from NIR/Red or NIR/Amber indices measured with Crop Circle active sensors on 12 July. Therefore, the in-season sufficiency index (SI) by NIR/Red or NIR/Amber index from Crop Circle active sensors can be used for determination of N application rate.

• Journal of Wetlands Research
• /
• v.23 no.4
• /
• pp.287-295
• /
• 2021

As facilities such as dam reservoir wetlands and agricultural irrigation reservoir wetlands are built, sedimentation occurs over time through erosion, sedimentation transport, and sediment deposition. Sedimentation issues are very important for the maintenance of reservoir wetlands because long-term sedimentation of sediments affects flood and drought control functions. However, research on resignation has been estimated mainly by empirical formulas due to the lack of available data. The purpose of this study was to calculate and compare the sediment deposition rate by developing a multiple regression model along with actual data and empirical formulas. In addition, it was attempted to identify potential causes of collapse by applying it to 64 reservoir wetlands that suffered flood damage due to the long rainy season in 2020 due to reservoir wetland sedimentation and aging. For the target reservoir, 10 locations including the GaGog reservoir located in Miryang city, Gyeongsangnam province in South Korea, where there is actual survey information, were selected. A multiple regression model was developed in consideration of physical and climatic characteristics, and a total of four empirical formulas and sediment deposition rate were calculated. Using this, the error of the sediment deposition rate was compared. As a result of calculating the sediment deposition rate using the multiple regression model, the error was the lowest from 0.21(m³km²/yr) to 2.13(m³km²/yr). Therefore, based on the sediment deposition rate estimated by the multi-regression model, the change in the available capacity of reservoir wetlands was analyzed, and the effective storage capacity was found to have decreased from 0.21(%) to 16.56(%). In addition, the sediment deposition rate of the reservoir where the overflow damage occurred was relatively higher than that of the reservoir where the piping damage occurred. In other words, accumulating sediment deposition rate at the bottom of the reservoir would result in a lack of acceptable effective water capacity and reduced reservoir flood and drought control capabilities, resulting in reservoir collapse damage.

• Korean Journal of Heritage: History & Science
• /
• v.54 no.4
• /
• pp.192-211
• /
• 2021

In Seongju, Gyengsangbuk-do, the Placenta Chamber (胎室, Taesil) of 18 sons and a son of the crown prince of King Sejong(世宗大王) is located in one place. Taesil refers to the place where the umbilical cord and placenta, which are separated when the baby is born, are placed in a jar made of pottery and stone box and then buried on the ground. The placenta chamber in Seongju has the Buncheong ware (粉靑沙器) cover buried on the ground to protect the baby's placenta. These covers are all hemispherical, with a diameter of more the 20cm. The decorations were made using black and white inlaid techniques only on the outside. The Buncheong ware cover with this shape and pattern has been confirmed only in the placenta chamber in Seongju. This study targets 6 of the Buncheong ware cover whose owners were identified, when and where they were prepared, what the stylistic features and meanings are, and where it was produced. The results of the study are as follows. First, ss a result of reviewing the production background and procurement system of this bowl, it was inferred that it was sourced from Jangheunggo (長興庫) at the central government office, between 1436 and 1439, when the event to bury the placenta of royal members in the ground was the most active. Second, it analyzed the unique features of this cover, such as the shape, pattern, and baked traces. The shape and pattern were compared to the ritual objects contained in the Sejong Silok Oryeui (『世宗實錄』 「五禮」, Five Rites of King Sejong Chronicle) and the lid of the royal placenta jar made in the 15th and 16th centuries. Third, this study suggests that the baking method was based on the shape and location of the traces remaining outside the cover. Finally, the following data were used to estimate the production site: the relationship with the 'Jagiso (磁器所, ceramic workshop) registered in the Sejong Silok Jiriji (『世宗實錄』 「地理志」, Geographical Appendix of King Sejong Chronicle); various records of contribution and dedication about the Buncheong ware made here; and the Buncheong ware and related tools excavated from the kiln site in the area. The place where the Buncheong ware cover was produced is estimated to be the most likely production site for the kiln site in Chunghyo-dong Kiln Site, located in Jeolla-do province by synthesizing the data above.

• Korean Journal of Remote Sensing
• /
• v.37 no.5_1
• /
• pp.1135-1147
• /
• 2021

In order to geometrically correct high-resolution satellite imagery, the sensor modeling process that restores the geometric relationship between the satellite sensor and the ground surface at the image acquisition time is required. In general, high-resolution satellites provide RPC (Rational Polynomial Coefficient) information, but the vendor-provided RPC includes geometric distortion caused by the position and orientation of the satellite sensor. GCP (Ground Control Point) is generally used to correct the RPC errors. The representative method of acquiring GCP is field survey to obtain accurate ground coordinates. However, it is difficult to find the GCP in the satellite image due to the quality of the image, land cover change, relief displacement, etc. By using image maps acquired from various sensors as reference data, it is possible to automate the collection of GCP through the image matching algorithm. In this study, the RPC of KOMPSAT-3A satellite image was corrected through the extracted matching point using the UAV (Unmanned Aerial Vehichle) imagery. We propose a pre-porocessing method for the extraction of matching points between the UAV imagery and KOMPSAT-3A satellite image. To this end, the characteristics of matching points extracted by independently applying the SURF (Speeded-Up Robust Features) and the phase correlation, which are representative feature-based matching method and area-based matching method, respectively, were compared. The RPC adjustment parameters were calculated using the matching points extracted through each algorithm. In order to verify the performance and usability of the proposed method, it was compared with the GCP-based RPC correction result. The GCP-based method showed an improvement of correction accuracy by 2.14 pixels for the sample and 5.43 pixelsfor the line compared to the vendor-provided RPC. In the proposed method using SURF and phase correlation methods, the accuracy of sample was improved by 0.83 pixels and 1.49 pixels, and that of line wasimproved by 4.81 pixels and 5.19 pixels, respectively, compared to the vendor-provided RPC. Through the experimental results, the proposed method using the UAV imagery presented the possibility as an alternative to the GCP-based method for the RPC correction.