• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.4
• /
• pp.353-362
• /
• 2007

Unlike large satellites, small satellites, such as nanosatellite and microsatellite, can provide a limited interior space for components mounting. In order to mitigate this issue, the compact Bus Electronic Unit(BEU) that integrates satellite electronic modules, combining most of bus subsystems and payload electronic modules into one unit, has been developed for HAUSAT-2 nanosatellite. This paper addresses the design and environmental test result analyses of BEU. The vibration and thermal vacuum tests were conducted at qualification level for the verification of design margin of newly developed BEU. The performance of individual electronic subsystem modules has been verified through performance tests before and after the qualification tests. It was confirmed that the natural frequency of BEU satisfies the design stiffness requirement without structural damage in the vibration test. Thermal analysis results were also almost consistent with test results through modified thermal analysis modeling.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.8
• /
• pp.767-773
• /
• 2010

This paper describes development of a non-explosive separation device which can be equipped on small satellites. The spur geared micro DC motor, which has high reliability and advantage of price, is adopted as an actuator. The proposed separation device has resettability and it does not need extra jig to reload. In addition, the simple structure makes it easy to fabricate and assemble. To verify the performance of the proposed device, the response time tests, maximum preload tests and maximum shock level tests were performed. Also, through the vibration tests and thermal vacuum tests, feasibility of the proposed separation device was shown in launching and space environments. Therefore, we expect that the proposed separation device can replace the imported separation devices in near future.

• Journal of Aerospace System Engineering
• /
• v.17 no.2
• /
• pp.94-102
• /
• 2023

A nylon wire holding and release mechanism (HRM) has been widely used for deployable applications of CubeSat owing to its simplicity and low cost. In general, structural safety of solar panel with an HRM has been designed by performing structural analysis under a launch environment. However, previous studies have not performed thermal analysis for HRM in an on-orbit environment. In this study, Launch and Early Orbit Phase (LEOP) thermal analysis was performed to evaluate thermal stability of the mechanism in the orbital thermal environment of the pogo pin-based HRM applied to CubeSat. In addition, the effectiveness of the thermal design and performance of the pogo pin-based HRM were verified through a thermal vacuum test.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.2
• /
• pp.156-164
• /
• 2016

Qualification model(QM) of main payloads including concentrating photovoltaic system using fresnel lens, heating wire cutting type shockless holding and release mechanism, and MEMS-based solid propellant thruster have been developed for the STEP Cube Lab.(Cube Laboratory for Space Technology Experimental Project), which is a pico-class satellite for verification of core space technologies. In this study, we have verified structural safety and functionality of the developed payloads under a qualification temperature range through the QM thermal vacuum test. Additionally, a reliability of thermal model of the payloads has been confirmed by performing a thermal correlation based on the thermal balance test results.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 2009.04a
• /
• pp.265-266
• /
• 2009

구글 어스(Google Earth)란 도구는 인공위성에서 찍은 사진들을 바탕을 3차원 지구 타원체에 바탕에 입힌 도구이다. 이 도구는 3차원 공간에서 OpenAPI등을 이용하여 3차원객체를 지구 타원체상에 구현 할 수 있다. 이러한 점들 때문에 많은 사람들이 주요 건축물을 구현하거나 실외 이동객체(자동차, 비행기 등)를 구현하여 더욱더 지구와 가까운 모형으로 구현을 해 왔다. 하지만 공간 정보란 것은 실외 공간정보만이 아닌 건물의 내부 구조나 쇼핑몰상의 유동 인구의 움직임등과 같은 정보도 존재한다. 이 연구는 구글 어스 상에서 내부 구조를 가진 건물을 구축하고 이곳을 탐색할 수 있게 해 주며 또한 실내 이동 객체들의 실시간 움직임을 구현한다.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.2
• /
• pp.11-19
• /
• 1999

The design procedure as well as some test results of a low-cost commercial radome for mobile DBS(Direct Broadcasting Satellite) receiving antenna system are presented in this paper. At first the complex permittivity of dielectric material should be measured in order to select a material for radome design. The complex permittivities of low-cost plastics supplied by domestic vendors are measured and presented. And then the transmission losses of the sheets are calculated. The calculated results are verified by the measurements of wave transmission test of that sheets. Two kinds of radomes, ABS single-layer and A-Sandwich((PET-Foam-ABS), are fabricated and measured practically. The transmission losses of single-layer and A-sandwich radome are 1.5dB and 0.6dB respectively at the maximum wave incident angle of 57 degree. Also the calculated crosspolarization caused by A-sandwich radome is under 20dB.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.281-285
• /
• 2007

The flow characteristics in the thruster should be analyzed considering its geometry and the pressure ratio to estimate its performance and etc. This paper suggests the computational result of an axisymmetric real nozzle for the altitude control of a satellite to find out the application limit that the assumption of continuum mechanics holds. The steady non-reacted compressible flow field in the unstructured grid system is computed and analyzed with varying the environmental pressure (or the degree of vacuum) under the fixed pressure ratio in a real thruster of which the area ratio of exit to throat is 56. The assumption of the continuum mechanics is not approved when the environmental pressure is reduced less than $10^{-3}$ atm.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.3
• /
• pp.80-89
• /
• 1998

Propulsion subsystem transfers KOMPSAT into mission orbit and controls its attitude. Design factor consists of structure safety, electrical circuit design, consumable power estimation of thermal hardwares, damping device design of fuel transient pressure, and system configuration design by considering plume effect from thruster firing. System level analysis should be performed for verification of system design under launch vehicle and orbital environment. Electrical functional test of thermal control hardware, proof pressure test, cleanliness verification test, and internal/external leakage test of fuel feeding system should be carried out for performance estimation of propulsion system. Design and assembly process of propulsion subsystem was depicted and reliability of system was verified by test analysis in this paper.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.6
• /
• pp.124-129
• /
• 2002

KAISTAT-4 is the fourth experimental microsatellite of KITSAT series which has been developed by Satellite Technology Research Center of KAIST for the last two years. The launch of KAISTSAT-4 is scheduled in 2003. The primary experimental payloads consist of Far-ultraviolet Imaging Spectrograph and Space Physis Package. In a similar way to KITSAT series, the interior of KAISTSAT-4 comprises mainly a set of stacked aluminium-alloy module boxes, each being capable of acting as the primary load path in the mechanical structure. The KAISTSAT-4 qualification model is now designed, fabricated, integrated, and tested to verify if the electrical and mechanical components work and can withstand the launch environments. All the required structural tests have been performed to a sufficient degree to satisfy the intent of the test requirements. This paper presents the structural system and launch environmental test results of KAISTSAT-4 qualification model.

• Journal of Astronomy and Space Sciences
• /
• v.18 no.2
• /
• pp.153-162
• /
• 2001

In this paper, space radiation environment and total ionizing dose(TID) effect have been analyzed for the KOMPSAT-2 operational orbit. It has been revealed that the trapped protons are concentrated in the SAA(South Atlantic Anomaly) area and that the trapped protons and electrons, and solar protons are main factors affecting TID. It turned out that low energy Particles can be effectively blocked by aluminum shielding thickness, but high energy Particles can not be effectively blocked by increasing aluminum shielding thickness. KOMPSAT-2 total radiation dose which is accumulated continuously to spacecraft electronics has been expressed as the function of aluminum thickness. These values ran be used as the criteria for the selection of electronic parts and shielding thinkness of the KOMPSAT-2 structure or electronic box.