• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.1
• /
• pp.211-218
• /
• 2000

This paper describes the improvement of broadband radio channel characteristics using a MMSE adaptive equalization technique as a fundamental study of high transmission rates in indoor radio channel. First, the performance of 16-QAM system that employs a MMSE linear adaptive equalizer in Rayleigh fading channel is analyzed. Next, in order to improve broadband radio channel characteristics, we apply an adaptive equalization technique employing the MMSE algorithm to the radio channel measured by using circularly polarized antenna under indoor NLOS(non-line-of sight) environment. Consequently, for 16-QAM with adaptive equalizer, we can achieve the improvement of about 13 dB at $10^{-3}$ error rate as compared with general 16-QAM. Moreover, it was found that the adaptive equalization technique could improve broadband radio channel characteristics over the all measured areas. Also, it was found that the employing both adaptive equalization and polarization diversity technique together could improve broadband radio channel characteristics and reduce fading more effectively.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.10 no.1
• /
• pp.111-116
• /
• 2017

We propose the compact circular polarized antenna. The radiation elements of the proposed antenna is designed using FR4 substrate with the size of $25mm{\times}3.2mm{\times}5mm$ and stand on four corners of the feed network substrate. The feeder network is designed on FR4 substrate with the size of $40mm{\times}40mm{\times}0.8mm$ and has four oupt signals with same magnitude and $90^{\circ}$ phase difference. The input impedances of the designed radiation elements and the output impedances of the feeder network are $100{\Omega}$. The designed antenna has the dimension of $40mm{\times}40mm{\times}5.8mm$ and the operated frequency band of 1.559 - 1.609 GHz. The fabricated antenna has RHCP radiation pattern and the measured results of axial ratio less than 3.5 dB and radiated gain more than 1.5 dBic. The fabricated antenna can apply to GLONASS and Beiodu systems as well as GPS system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.9 s.100
• /
• pp.893-902
• /
• 2005

We propose a novel single-feed triangular patch antenna with bar-type slots for dual-band circular polarization operation. And also propose a H-type slotted triangular patch antenna to enhance the ratio of the resonance frequencies. 3 cases of desist examples with bar-type slots were investigated and also 4 cases of H-slotted antennas were investigated to meet the dual-band requirement for GPS(Global Positioning System) and DMB(Digital Multimedia Broadcasting). One suitable design example was implemented and measured. Simulation results of the design example for GPS and DMB system show that axial ratio and maximum gain are 3.80 dB, 8.85 dBi for low-band at 1.575 GHz and 2.02 dB, 8.60 dBi for high-band at 2.642 GHz, respectively. Measured results of the implemented antenna show that $S_{11}$ is -12.43 dB for low-band at 1.575 GHz and less than -18.75 dB for high-band, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.2 s.117
• /
• pp.158-165
• /
• 2007

In this paper, the circularly polarized $4{\times}4$ array antenna is proposed for the X-band. A single antenna consists of square patch and unequal cross-aperture coupled feeding. The RHCP(Right Handed Circularly Polarization) is generated by unequal cross-aperture coupled feeding. By reducing space among elements of way antenna from 0.8 ${\lambda}_0$ to 0.45 ${\lambda}_0$, the mounting area of array antenna is miniaturized. The $2{\times}2$ array antenna is designed using sequential rotation feeding network. The good level of gain, axial ratio, and impedance bandwidth are achieved. The $4{\times}4$ array antenna is extended by ${\lambda}/4$ transformer and T-junction power divider. The simulated maximum radiation gain is 15.09 dBi at 10 GHz. The simulated 3 dB Axial Ratio bandwidth is from 9.05 to 10.4 GHz(13.5%). Also the measured impedance bandwidth($VSWR{\leq}2$) of manufactured $4{\times}4$ array antenna is from 8.45 to 11.84 GHz(33.9%). The measured maximum radiation gain is 11.10 dBi at 10 GHz. The measured 3 dB Axial Ratio bandwidth is from 9.42 to 10.47 GHz(10.5%).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.1 s.116
• /
• pp.62-75
• /
• 2007

This paper describes a shaped-beam antenna for increasing the antenna gain of a radiating element. The proposed antenna structure is composed of an exciting element and a multi-layered disk array structure(MDAS). The stack micro-strip patch elements were used as the exciter for effectively radiating the electromagnetic power to the MDAS over the broadband, and finite metallic disk array elements - which give the role of a director for shaping the antenna beam with the high gain - were finitely and periodically layered onto it. The efficient power coupling between the exciter and the MDAS should be carried out in such a way that the proposed antenna has a high gain characteristic. The design parameters of the exciter and the MDAS should be optimized together to meet the required specifications to meet the required specifications. In this study, a shaped-beam antenna with high gain was optimally designed under the operating conditions with a linear polarization and the frequency band of $9.6{\sim}10.4\;GHz$. Two methods constructed using thin dielectric film and dielectric foam materials respectively were also proposed in order to implement the MBAS of the antenna. In particular, through the computer simulation process, the electrical performance variations of the antenna with the MDAS realized by the thin dielectric film materials were shown according to the number of disk array elements in the stack layer. Two kinds of antenna breadboard with the MDAS realized with the thin dielectric film and dielectric foam materials were fabricated, but experimentation was conducted only on the antenna breadboard(Type 1) with the MDAS realized with the thin dielectric film materials according to the number of disk array elements in the stack layer in order to compare it with the electrical performance variations obtained during the simulation. The measured antenna gain performance was found to be in good agreement with the simulated one, and showed the periodicity of the antenna gain variations according to the stack layer number of the disk array elements. The electrical performance of the Type 1 antenna was measured at the center frequency of 10 GHz. As the disk away elements became the ten stacks, a maximum antenna gain of 15.65 dBi was obtained, and the measured return loss was not less than 11.4 dB within the operating band. Therefore, a 5 dB gain improvement of the Type 1 antenna can be obtained by the MDAS that is excited by the stack microstrip patch elements. As the disk array elements became the twelve stacks, the antenna gain of the Type 1 was measured to be 1.35 dB more than the antenna gain of the Type 2 by the outer dielectric ring effect, and the 3 dB beam widths measured from the two antenna breadboards were about $28^{\circ}$ and $36^{\circ}$ respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.6
• /
• pp.642-650
• /
• 2010

In this paper, we study a TT&C link to obtain a required specifications of TT&C(Telemetry Tracking and Command system) antenna for an LEO(Low Earth Orbit) satellite. The premised mission orbit is the sun-synchronized and circular orbit and it performs earth-space observations. We design minimum TT&C link-budget to obtain required antenna beamwidth and gain. The proposed turnstile antenna provides wide beamwidth and circular polarization. We suggested the attaching position that shows the most effective results by confirming the variation of antenna performance when the proposed antenna is adapted to satellite's various positions. Also we proved the proposed antenna's ability while it is performing the mission through the orbit simulation based on the electrical performance of the proposed turnstile antenna.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.05a
• /
• pp.63-64
• /
• 2018

In this study, a design method for a circular polarization patch antenna operating at a frequency 1.5 GHz~1.7 GHz was studied. To obtain the wide bandwidth and high gain, air substrate between patch and ground plane was applied. The impedance bandwidth is improved by adjusting the sizes of patch, the distance between main patch and ground plate, the length of internal slots, the position of feeding point, the length of external stub, etc. The antenna is designed and simulated for an operation in the frequency range of 1.5GHz~1.7GHz band. The results show that antenna characteristics such as return loss, gain, axial ratio, radiation patterns are appropriate for the satellite navigation system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.5
• /
• pp.748-754
• /
• 2000

A novel single feed wide band CP stacked microstrip antenna using crossed slots has been designed, fabricated and measured. For the single rediating element the designed 10dB return loss bandwidth is 34.5%99.45~13.54 GHz), 3dB axial ratio bandwidth is 18.7%(11.17~13.39GHz), and 6 dB gain bandwidth is 29%(10.21~13.64GHz). For the 2$\times$2 array designed using a sequential rotation method, the 10dB return loss bandwidth is 35.9%(9.69~13.94GHz), 3dB axial ratio bandwidth is 34.6GHz (9.93~14.03GHz), and 6dB gain bandwidth is 27.4%(10.35~13.6GHz). For the fabricated 8$\times$8 array antenna, the 10dB return loss bandwidth is 27.3%(10.17~13.41GHz), 3dB axial ratio bandwidth is 27.9GHz(10.1~13.4GHz), and the radiation pattern is good agreement with theory. This antenna can be used for broadband applications for communications or broadcasting in Ku band.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.2058-2060
• /
• 2004

In this paper, circular polarized antennas of Tx 30GHz and Rx 20GHz are implemented in LTCC process. Tx antenna has a circular patch structure and Rx antenna has a ring patch structure. The feeding line of Tx antenna is placed in the center hole of Rx ring patch antenna which is printed under Tx circular patch antenna layer. It makes antenna size smaller. Tx antenna's return loss in under -10dB level from 30GHz to 31GHz and Rx antenna is under -10 dB from 20GHz to 21GHz. The isolation between two antennas is less than -20dB. Axial ratio is less than 3dB though out each band.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.3
• /
• pp.471-477
• /
• 2013

We have studied on the possibility of precise positioning using hybrid Track Circuit system. Hybrid Track Circuit uses RFID which replaces UHF. Hybrid Track Circuit is a part of next generation railroad signal system which is available to communicate with a railway on board system based on a realtime operating system. If applicate on a current hand operating subway, phenomenon caused by driver's mistake such as passing a stop without stopping or mismatch error between PSD and train door should be prevented.