• Proceedings of the KAIS Fall Conference
• /
• 2012.05b
• /
• pp.778-780
• /
• 2012

국내 전동차에는 슬라이딩 도어가 널리 사용되고 있으나 노이즈에 취약한 단점이 있었다. 저속 운행시에는 외부로부터 유입되는 소음이 문제가 되지 않았으나, 전동차가 고속으로 운행되면서 소음이 큰 이슈로 자리 잡게 되었다. 전동차 소음의 주요 요인은 도어시스템에서 외부로부터 유입되는 공기를 완전히 차단하지 못해서 발생하게 된다. 플러그 도어시스템은 구조상 노이즈 문제에 강한 특성을 가지고 있다. 그러나 현재 플러그 도어는 국산화가 이루어져 있지 않아 국산화를 위해 전기식 플러그 도어를 개발하여 시험을 진행 중에 있다. 본 논문에서는 개발한 전기식 플러그 도어시스템의 개발 내용 및 구성에 대해 다루고자 한다.

• Journal of Korean Society of Transportation
• /
• v.28 no.6
• /
• pp.85-97
• /
• 2010

The present study aims at estimating the model of bus bunching duration along with its influential determinants in an attempt to understand the status of bus bunching being created by buses from various routes converging into one bus stop. To do so, the duration analysis, a well-known survival analysis, was adopted in order to capture the distribution of duration time as for 8 base lines, accordingly developing the model best fit for weibull distribution. Key attention to draw out the duration time model for bus bunching phenomena was laid, by analyzing 18 impact factors, on such criterion variables as number of berth, number of bus line in each berth and maximum capacity of on-and-off passengers in each line. Comparison in two typical types of bus lane was made between bus-only center lane(Dobong Mia-ro) and normal street-side lane(Tongil Euiju-ro). In this regard, the study, based on the model as above, suggested appropriate alternatives to improve the bus operation by effectively controlling bus bunching.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.4
• /
• pp.2324-2329
• /
• 2014

The inspection of distance to go train control system conducted only when train is in main line or inspecting line, that affects low work efficiency and hazard elements to safe operation. Before or after train operation, the interface test between on-board and wayside signal system must be conducted. In this paper, onboard signal interface inspection system based on the real-time automatic analysis of onboard system status information that is transmitted to the wayside system and the operation status check of the onboard signal device operates as a virtual train information that is transmitted to the onboard system have been proposed. And after building the inspection system to the inspecting track of Daejeon Subway Line 1, Panam Depot, the verification algorithm of proposed interface test and the results was presented. therefore, it has enhanced work efficiency to do not carry train operation of a half hour in test line to test on-board system.

• Journal of Korean Society of Transportation
• /
• v.25 no.5
• /
• pp.111-122
• /
• 2007

This paper investigates the rail service patterns by train class. The emphasis in intercity rail planning is to more efficiently use of existing station facilities. Rail transit operations are affected by the system layout and ridership patterns and by work rules. Operations are also influenced by past practices and the institutional setting. Main factors to decide train service patterns are the location, socioeconomic characteristics, land use and travel demand of the station. In this context, the travel demand of intercity rail station is of crucial significance. Tests on a KTX case shows that train service frequency can be efficiently decreased in weekday to transport the same passenger demand. The work has shown many subjects that need further research including various factors influencing on train frequency. This study serves the railroad authorities in planning and determining business strategy in the increasingly competitive environment of regional rail transport.

• Journal of the Korean Geographical Society
• /
• v.43 no.4
• /
• pp.544-560
• /
• 2008

This study seeks to clarify the background and factors for the expansion of bus networks that connect Incheon International Airport with its hinterlands. For this research objective, this paper analyzes the relationships among the change of bus routes, competitive transportation modes, passenger fares, and the shortest time distance. Previously, the hinterlands of route bus networks that connect Gimpo International Airport were Seoul metropolitan area, Chungcheong region, Jeonju and Iksan in Jeollabuk-do(province). However, the opening of Incheon International Airport resulted in the expansion of the hinterlands of bus networks to Gangwon-do, Gwangju, and major cities in Youngnam region. Simultaneously, route bus networks also expanded in Seoul metropolitan area. Each bus route connecting Incheon International Airport with its hinterlands was opened by a single bus company or various bus companies. In many cases, due to the uncertainty of revenues or bus company's regional ties, a bus route was opened by various bus companies. In this paper, the analysis of the number of one-way route bus service and density of flight passengers shows that the frequency of the route bus service for Seoul except Gangseo-gu(ward) and for Seoul's satellite cities(Suwon, Seongnam, Anyang, Gunpo, Guri, and Osan) should be decreased. The analysis also shows that the frequency of the route bus services for the other cities, counties(Guns), and wards(gus) should be increased. In Seoul metropolitan area, although route bus fares are more expensive than subway fares, passengers use route bus more frequency than subway because time distance of route bus is shorter than that of subway and subway transfer is inconvenient. In general, outside Seoul metropolitan area, air flight is preferred in the regions that have airports. In contrast, the route bus is preferred in Daegu and other regions that do not have airports.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.5
• /
• pp.103-111
• /
• 2021

The purpose of this study is to study a method for preventing collisions of multiple drones in controlled airspace. As a result of the study, it was proved that it is appropriate as a method to control drone collisions after setting accurate information on the ROI (Region of Interest) area estimated based on the expected drone path and time in the control system as a method to avoid drone collision. As a result of the empirical analysis, the diameter of the flight path of the operating drone should be selected to reduce the risk of collision, and the change in the departure time and operating speed of the operating drone did not act as an influencing factor in the collision. In addition, it has been demonstrated that providing flight priority is one of the appropriate methods as a countermeasure to avoid collisions. For collision avoidance methods, not only drone sensor-based collision avoidance, but also collision avoidance can be doubled by monitoring and predicting collisions in the control system and performing real-time control. This study is meaningful in that it provided an idea for a method for preventing collisions of multiple drones in controlled airspace and conducted practical tests. This helps to solve the problem of collisions that occur when multiple drones of different types are operating based on the control system. This study will contribute to the development of related industries by preventing accidents caused by drone collisions and providing a safe drone operation environment.

• Proceedings of the KSR Conference
• /
• 2006.05b
• /
• pp.999-1005
• /
• 2006

• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.1240-1246
• /
• 2006

Generally, there are two types of main factors to affect output power quality of a auxiliary power supply an EMU(electric multiple unit). One is a voltage flicker by amplitude modulation of short time and air compressors. The other is repetitive motion of large capacity motor such as air compressors, HVAC unit etc. in main factors. This paper compared two kinds of fluorescent lamp, 32W (after remodeling interior) and 40W(before remodeling interior) and measured the light output varying input power(AC220V) for a flicker phenomenon related power supply of lamps in EMU. Also, we analyzed a flicker considering EMU operating time and density in order to grasp main factors of a load change to cause a voltage change. As a results of test, a 40W fluorescent lamp was more insensitive with 20.26% degree an eye recognition degree sides about changes of the input power and lower with 19.9% voltage side generating flicker compare with fluorescent lamp 32W. Also, we confirmed the fact which the fluorescent lamp flicker was generated by varying fluorescent lamp output voltage when the commercial EMU was in high driving density and at the busy time. Additionally, we confirmed the frequency band which an EMU passenger could feel sensitively blinking of a fluorescent lamp was visually $8Hz{\sim}15Hz$.

• Journal of Korean Society of Transportation
• /
• v.29 no.2
• /
• pp.15-24
• /
• 2011

This study discusses an equity analysis performed to supplement the existing bus service evaluation system. The equity of 179 feeder bus routes in the city of Seoul(Year 2009) is analyzed by employing the modified BCC model along with the desirable inputs such as a number of bus stops and a frequency of operations. In the analysis, each DMU (Decision Making Unit) is assumed to use the desirable inputs, and produces both the index of equity and the index of accessibility. We apply an input-oriented modified BCC model to analyze the equity of the DMUs. The computational result indicates that only 9% of the feeder bus routes are equitable among the total DMUs and the average equity estimate is 0.702. It is also suggested that on average approximately 60% increases of desirable inputs (i.e., a number of bus stops and a frequency of operations) are needed in order to improve equity of DMU in the city of Seoul. The result of the tobit regression analysis on the determinant factors affecting the equity of DMUs shows that all the independent variables (i.e., a number of bus stops and a frequency of operations) are statistically significant at 5% significance level, and the number of bus stops is found to be the most influential factor.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.7 no.2
• /
• pp.131-139
• /
• 1987

The purpose of this study is to define the primary factors obstructing the bus services that play an important part in mass transportation in almost the cities, and then to develop the models for travelling speed. To define the primary factors, two video cameras were used in this study, one for speed meter, the other for traffic condition, from which time-speed graphs were made. In the graphs, the gaps between road regulation speed and travelling speed were analyzed by monitor analysis. After this, primary delay factors were classified by quantification theory type I. and then to develop the models for travelling speed, stepwise analysis was used.