• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.2
• /
• pp.160-167
• /
• 2009

To detect islanding mode when the grid is being tripped is a major safety issue in the Utility Interactive Photo Voltaic (UIPV) system. In this paper, analytical design method is suggested for AFD & RPV method under IEEE 929-2000 recommended islanding test condition. We have discussed that there is a same point. we injected reactive component of the current by AFD & RPV methods, but the current reference generated is other waveform. Possible if amount of reactive components in this methods are same each method, there is happened same rates frequency variation. To verify the validity of the analytical comparison, this paper presents simulation and experimental results from single phase, 3[kW] inverter for the transformerless UIPV system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.3
• /
• pp.239-246
• /
• 2003

Brushless D.C. Motor is widely used for industrial application because of high efficiency and high power density. Especially, in home appliance, BLDCM is very useful due to high control performance and low acoustic noise. In this paper, BLDCM and its controller are designed and developed for tread mill application. With the restricted stator structure, permanent magnet rotor is designed for manufacturing and cost effectiveness using CAD and FEM analysis. A ferrite magnetic material is used as a rotor magnet for the cost and temperature advantages. For a stable operation of tread mill, over current and temperature can be detected and protected. The designed BLDCM and its controller was verified by the experimental results.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.4 no.3
• /
• pp.193-198
• /
• 2003

A rotor dynamic analysis is implemented to confirm the vibration stability of the high speed centrifugal chiller coupled with gear system. As the rotating speed of the centrifugal chiller under investigated is increased up to 17,605 rpm at the pinion rotating part, the bearing instability is getting higher and, furthermore, the rotor-bearing system might experience a few critical speed which lead to system failure due to the excessive vibration. In this study, considering the loading capacity and stability conditions, offset journal bearings are adopted for the pinion rotating system and general cylindrical bearing are used for motor part. From the modal analysis, the system is found to be stable as the synchronous rotating frequency does not come across with any whirl natural frequency and, in addition, the critical damping ratio which shows the damping characteristics of the system are positive over the all operating ranges. From these results the authors confirm the vibration stability of the rotor-bearing system suggested in this study.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.1
• /
• pp.25-29
• /
• 2004

This paper is to research about design and drive system of a switched reluctance motor for a pallet truck application. SRM is suitable for a pulse type source and is researched for home and industrial applications owing to the advance of power electronics technology. An SRM for a pallet truck drive is developed and tested. The drive system has to operate with low voltage and high current. The small size, robustness and high efficiency make it possible to replace with DC motor which is used in a pallet truck conventionally. Test results show that pallet truck with SRM has better drive characteristics than that of the DC motor performance.

• Journal of the Microelectronics and Packaging Society
• /
• v.13 no.1 s.38
• /
• pp.57-61
• /
• 2006

Fuel cells are direct current (DC) power generators. They generate electricity through an electrochemical process that converts the energy stored in a fuel directly into electricity. Fuel cells have many benefits, which produce no particulate matter, nitrogen or sulfur oxides. And they have few moving parts and produce little or no noise. When fueled by hydrogen, they yield only heat and water as byproducts. Their wide application can reduce our dependence on fossil fuels and foreign sources of petroleum. This paper is studied on a high efficiency power conditioning system (PCS) applied to the proton exchange membrane fuel cell (PEMFC) generation system. This paper is designed to a novel PCS circuit topology of high efficiency. Some experimental results of the proposed PCS is confirmed to the validity of the analytical results.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.11
• /
• pp.1603-1611
• /
• 2021

As IMO environmental regulations are tightened, the need to establish a system that can reduce emissions is increasing, and for this purpose, various power control management systems have been studied and implemented as a new energy management system for ships. In this study, we design a control process through modeling for Bi-Directional Converter (BDC) application with bi-directional power flow to link batteries, which are energy storage devices, to conventional generator power systems, and propose mechanisms for batteries optimized for varying loads. This work models MATLAB/Simulink as a BDC and simulates current control and state of charge (SOC) optimization at the time of charging and discharging batteries according to load scenarios. Through this, the battery, power, and load were interlocked so that the generator operated on board could be operated in the optimal operation range, and power control management was performed to enable the generator to operate in the high fuel efficiency range.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.17-18
• /
• 2008

IEC 61850은 변전소 자동화에 있어서 변전소 감시, 보호, 제어, 운전에 필요한 모든 부분에 IT 기술을 적용한 디지털 제어 기반의 차세대 변전소 자동화 시스템을 설계, 개발, 운용하는 기술로서 변전소 운전의 자동화 및 무인화를 위한 핵심 기술이다. IEC 61850 기반의 변전소 자동화 시스템의 스테이션 레벨 Station HMI 구현을 위하여 논리노드 데이터 클래스가 매핑된 MMS와 OPC를 연계하였으며 OPC 통신을 지원하는 HMI툴을 사용하여 IEC 61850 스테이션 레벨 Station HMI를 구현하였다.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.15 no.1
• /
• pp.30-35
• /
• 2005

An automatic transmission pattern with the fixed standard shift map can provide comfortable shift to driver. However it may be a complain to provide shift by the same shift pattern for driver because the inclination of a driver may be various. Therefore, in this paper, we design the decision module, which can decide the driving style using input to decide the inclination of the driver and driving manner. The goal of this paper is to calibrate the shift map according to the inclination of the driver using the decided driving manner from the proposed module. As a result, the proposed intelligent automatic transmission system can provide a suitable shift point and time to the driver. To verify the performance of the proposed system, the real data that is obtained from the road test will be used.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.93-93
• /
• 2011

고진공 펌프 국산화의 일환으로 터보분자 펌프와 크라이오 펌프 개발이 진행 중이다. 크라이오 펌프 개발은 기계연구원, 우성진공(주), 국민대학교가 연합해서 수행하고 있다. 올해 9월말에 끝나는 1단계 마지막 3차 년도에는 두 고진공 펌프 모두 시제품을 완성하고 성능을 입증해야 한다. 이를 위해 고진공 펌프 개발과 별도로 진공 펌프 종합특성평가 시스템 개발도 표준과학연구원 주도로 진행되고 있는데 크라이오 펌프 평가 시스템은 원자력연구원이 담당하고 있다. 완성된 크라이오 펌프 성능평가 장치는 상온 기준 5${\times}$10-11 mbar의 기저압력을 보이고 있어서 초고진공 영역에서 크라이오 펌프 운전성능을 평가할 수 있는 준비를 마쳤다. 현재 크라이오 펌프 냉동기는 전반적으로 목표 설계치에 근접한 냉각성능을 나타내고 있는데 예를 들면 2차 냉각단 냉각능력이 10 K, 10 W로 대형 크라이오 펌프를 제작하기에도 충분하다. 활성탄 어레이도 여러 모델들을 자작하여 배기성능을 시험해 보았으므로, 최종적으로 3,600 L/s 급에 적합한 어레이를 만들고 이를 개발된 냉동기에 얹고 열차폐와 몸통을 씌워 펌프로서의 운전성능을 평가하는 일이 남아있다. 시제품은 상용품과 달리 기기가 차지하는 공간이 크고 부대설비가 복잡해서 운전성능 평가 장치에 부착해서 실험하기 어려울 수도 있으므로 기계연구원 현장에서 진공 게이지와 기체도입구만 부착한 마구리 플랜지를 펌프 흡기구 위에 달고 간이로 배기속도를 측정하는 것도 고려하고 있다. 이 경우는 표준용기를 사용할 때보다 배기속도가 과대평가되므로 이를 보정해 주는 방안을 마련해 놓아야 한다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.6
• /
• pp.649-659
• /
• 2016

This paper describes control algorithm and control structure of vehicle control unit for range-extended electric vehicle equipped with engine-generator system, and specially presents methods which determine optimal operating points and decreases a vibration or a shock for operating the engine-generating system. The vehicle control algorithm is consisted of several parts which are sequence control, calculation of wheel demand torque, determination of operating points, and management of operating points and so vehicle controller has be made possible to efficiently manage calibration parameters. The control algorithm is evaluated by driving test modes, launching performance and operating engine-generator system and so on. In conclusion, this paper present methods for extending a mileage, improving a launching performance and reducing vibration or shock when the engine-generating system is starting or is stopping.