• Elastomers and Composites
• /
• v.44 no.3
• /
• pp.315-322
• /
• 2009

Influence of blend mode of extender oil on the properties of thermoplastic vulcanizates (TPVs), based on an ethylene-propylene-diene copolymer (EPDM) and a polypropylene (PP), was studied. The EPDM/PP TPVs were prepared in an open roll mill using two different modes in blending sequence of paraffinic oil and phenolic curative, i.e., Oil-Cure and Cure-Oil modes. Degree of cross-linking by gel fraction and properties such as hardness, tensile strength, elongation at break, and melt flow rate were investigated as a function of extender oil content for the two modes. Little influence of the blend mode of extender oil on the degree of cross-linking and mechanical behaviors was observed. However, the use of Cure-Oil mode in the preparation of EPDM/PP TPVs resulted in a marked increase in the level of processability as reflected by melt flow index, as compared to the use of Oil-Cure mode.

• The Korean Journal of Rheology
• /
• v.5 no.2
• /
• pp.136-143
• /
• 1993

PDSC(pressurized differential scanning calorimeter)를 이용하여 물 또는 물 -DMF(N,N-dimethylformamide) 혼합물을 함유한 아크릴로니크릴 중합체(wet-PAN)의 융점 거동을 조사하였으며 wet-PAN 용융체의 점도측정에 적합한 모세관형 점도계를 제작하여 전단속도 및 온도에 따른 점도변화를 고찰하였다. 물에 의한 wet-PAN의 융점 및 용융점도 는 물의 함량이 증가함에 따라 점근적으로 감소하여 25wt% 이상에서는 거의 일정하였다. 또한 물(25wt% 기준)의 일부를 DMF로 대체하였을 경우에는 융점이 감소하였다. 한편 wet-PAN의 용융점도는 power-law 거동에 준하였으며 물계에서는 power-law 지수(n)가 0.16(19$0^{\circ}C$)~0.18(17$0^{\circ}C$)인데 비하여 물(95)~DMF(5) 혼합물계에서는 0.24(175$^{\circ}C$)~0.25(16 5$^{\circ}C$)로서 점도의 전단담화거동이 약해졌으나 흐름의 활성화에너지는 다소 증가 하였다.

• Resources Recycling
• /
• v.17 no.3
• /
• pp.10-20
• /
• 2008

In order to study the behaviors of inorganic fillers in recycling of the waste agricultural plastic films, the washed PE fluffs from Shihwa and Jungeup Plant belonging to ENVICO were used respectively. First of all, the test pellets were manufactured by adding of inorganic fillers suchlike calcium carbonate and calpet by certain portions to PE fluffs and then the tested sheets were formed. The mechanical and thermal properties of the samples were measured and compared with others. The items measured were tensile, flexural, Izod impact, HDT, MFT, and so on. Morphologies were also investigated for various samples using the SEM. Finally, optimum ratios between recycled PE and inorganic additives were found out for the best products in physical condition as well as in economic point of view.

• Elastomers and Composites
• /
• v.44 no.2
• /
• pp.156-163
• /
• 2009

Our objective is to increase the flowability of Polypropylene(PP) compounds and achieve flow mark free surface in injection molded specimen. We have investigated flowabilities of PP compounds which were composed of PP, rubber, talc, and trace amount of additives. Flowability measurement was performed with four types PPs of which molecular weight distributions(MWD) and melt indexes(MI) were different. Rheological properties of the PP compounding materials, such as spiral flow(SF) length, MI, and shear viscosity, were evaluated. When PP with the broad MWD was used, there were remarkable cases where the spiral flow length of low MI PP compound was longer than that of higher MI PP compound. The PP compound having low MI but broad MWD PP has more flowability than the compound with only high MI.

• Applied Chemistry for Engineering
• /
• v.24 no.1
• /
• pp.104-111
• /
• 2013

Poymer blends of two degradable aliphatic polyesters, relatively expensive material polylactic acid (PLA) and relatively inexpensive material poly(butylene adipate-co-terephthalate) (PBAT), were used in this study. Three different kinds of modifiers were used with various amounts. Diisocyanate type methylenediphenyl 4,4'-diisocyanate (MDI) and hexamethylene diisocyanate (HDI) were used as modifiers and epoxy type coupling agents also used. The melt flow index (MFI) and dynamic viscoelasticity of various compositions of PLA/PBAT blends were studied. The mechanical property and morphology with respect to the fracture surface of PLA/PBAT blends were also investigated using tensile test and field emission scanning electronic microscopy, respectively. These tests were also used to verify the compatibility of PLA/PBAT and the effect of mechanical properties due to the use of modifiers. Tensile properties of PLA/PBAT blends modified with HDI were improved remarkably.

• Elastomers and Composites
• /
• v.42 no.3
• /
• pp.151-158
• /
• 2007

MWNTs have been widely investigated due to unique properties of such as good electrical conductivity and thermal stability in polymer composites industries. This paper established the procedure to fabricate PMMA/MWNT composites by a modular intermeshing co-rotating twin screw extruder with L/D ratio of 42. The electrical properties of PMMA/MWNT composites with different content of MWNT have been investigated. A sheet resistance percolation was observed at 4 wt% of MWNT for the melt processed composites. Sheet resistance of PMMA/MWNT composite film containing 4 wt% of MWNT was nearby $10^4{\Omega}/sq$ and this shows the possibility of potential application to EMI (Electronic Magnetic Interference) shielding materials. The characteristics of composites were analyzed by TGA, DSC, and SEM. In addition, MFI (Melt Flow Index) has been measured to analyze the rheological property.

• Composites Research
• /
• v.37 no.2
• /
• pp.68-75
• /
• 2024

Polypropylene (PP), a thermoplastic resin with excellent mechanical, thermal, chemical, and water resistance properties, has been attracting attention due to its economic efficiency and recyclability. However, repeated processing of thermoplastic resins can lead to property degradation, and the point at which quality degradation occurs varies depending on the processing conditions. In this study, we evaluated the performance changes of composite materials with repeated processing by blending PP resin with various additives and conducting extrusion and injection processes repeatedly. In addition, we evaluated the mechanical properties of composite materials to evaluate the effect of MFI value change during repeated processing on fiber impregnation in composite material processing.

• Polymer(Korea)
• /
• v.31 no.5
• /
• pp.399-403
• /
• 2007

Trans-esterification behavior of polycarbonate/poly(butylene terephthalate) (PC/PBT) blends was investigated during the melt mixing process. Rheological and fracture behaviors, and fracture morphology were also investigated as a function of PC/PBT blend ratio. Based on FT-IR and $^1H-NMR$ results, a trans-esterification reaction was confirmed to occur between PC and PBT during the melt mixing process. The melt index(MI) decreased with increased PC content, indicating the higher flow resistance of PC. The storage and loss moduli were increased by increasing the PC loading, and the PC/PBT blends were rheologically incompatible based on the Cole-Cole plot. The tensile property increased linearly with the increased PC content. However, the impact strength increased until 50 wt% of PC loading, notably around $30{\sim}40wt%$, and then was levelled off at 50 wt%. Rough ridges were formed on the impact fracture surfaces above the 40 wt% of PC content, supporting the observed higher impact strength in this range.

• Elastomers and Composites
• /
• v.49 no.3
• /
• pp.181-190
• /
• 2014

Melt grafting of itaconic acid (IA) onto an ethylene-propylene-diene terpolymer (EPDM) with various organic peroxide initiators was performed. Finding the optimum mixing conditions and concentration of ingredients is critical for effective grafting and optimum properties of grafted materials. This study focused on the effects of mixing conditions (temperature and time), initiator type/concentration and monomer concentration on the grafting degree and efficiency, melt flow index, and gel content of EPDM-g-IA. The initiator, 2,5-dimethyl-2,5-di(tert-butyl peroxy)-hexane (T-101), appeared to meet for the best grafting degree (1.91%). The grafting degree increased markedly by increasing the amounts of monomer IA and initiator T-101. The grafting degree also increased by increasing mixing temperature and time. The optimum monomer and initiator concentrations and reaction temperature and time were found to be about 5wt%/0.05wt% and $160^{\circ}C$/15min, respectively. It was found that the physical properties of EPDM-g-IA were higher than those of the pristine EPDM.

• Elastomers and Composites
• /
• v.48 no.1
• /
• pp.39-45
• /
• 2013

Melt grafting of citraconic acid (CCA) onto an ethylene-propylene-diene terpolymer (EPDM) with various peroxide initiators was performed using a Haake Rheocorder. Finding the optimum running condition and concentration is critical for effective grafting and performance of grafted material. Therefore, this study focused on the effects of mixing (reaction) condition and monomer/initiator dosages on the grafting degree, grafting efficiency and crosslinking degree (gel content), melt flow index and mechanical properties of CCA-g-EPDM. As the grafting degree/crosslinking degrees increased, the tensile strength increased significantly, but elongation at break and melt flow index decreased. The initiator 2,5-dimethyl-2,5-di(tert-butyl peroxy)-hexane (T-101) appeared to meet for the best grafting(2.31%). The grafting degree increased markedly with increasing monomer CCA/initiator T-101 contents. The grafting degree also increased with increasing mixing temperature/time, and then leveled off or decreased/increased a little. The optimum monomer/initiator dosages and reaction temperature/time were found to be about 5/0.05 wt% and $180^{\circ}C$/15min, respectively.