• Transactions of the Korean hydrogen and new energy society
• /
• v.32 no.4
• /
• pp.205-211
• /
• 2021

Recently, it is necessary for study on renewable energy due to environmental pollution and fossil fuel depletion. Therefore, in this study, the filling temperature according to the nozzle geometry was evaluated based on the limit temperature specified in SAEJ2601 for charging hydrogen, a new energy. There are three types of nozzles, normal, angle and round, fixed the average pressure ramp rate at 52.5 MPa/min, and the injection temperature was set at 293.4 K. As a result, the lowest temperature distribution was found in the round type, although the final temperature did not differ significantly in the three types of nozzles. In addition, Pearson's coefficient was calculated to correlate the mass flow rate with the heat transfer rate at the inner liner wall, which resulted in a strong linear relationship of 0.98 or higher.

• Fire Science and Engineering
• /
• v.26 no.4
• /
• pp.77-81
• /
• 2012

This study of aims to provide basic data for improve the performance of air respirators that generate by bad influencing elements in fire emergency field. With three types of conditions set up for these tests, the pressures of containers have been extracted; the ambient temperatures have been checked, and the generation of moisture inside and outside container have been checked and identified. Specifically, these tests have been conducted at temperatures ranging between $-20{\sim}40^{\circ}C$. The pressures of containers have been extracted to reach between 0.4~0.8 MPa, using a pressure regulating valve. These tests have resulted in no change in the temperature and moisture outside the containers and no generation of moisture inside the containers as well. Although moisture has been generated inside the pressure gauge, the amount of moisture has not exceeded 25 $mg/m^3$, i.e. the limit suggested by the Korean Government. Therefore, it is judged that the moisture generated inside air respirators, which can be the most critical issue in the equipment, is likely to be caused in the process of managing the equipment or replacing air in the equipment at places of end-users, rather than in the process of manufacturing and production of the equipment.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.6
• /
• pp.187-195
• /
• 1996

Because an alternative refrigerant(HFC-134a) is being used instead of CFC-12 for automotive air-conditioning system, newly designed air-conditioning components are necessary due to changes in characteristics. Optimum design scheme for receiver dryer in an automotive air-conditioning system is described with emphases upon the volume of desiccant and container. The volume of the container, that is manufactured based on the study, is reduced down to one half of the existing receiver dryers.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.5 no.1
• /
• pp.9-13
• /
• 2009

The containment local leakage rate testing in nuclear power plants is performed in accordance with ANSI/ANS-56.8(1994) in Korea. Two methods, the make-up flow rate and the pressure decay, are used for LLRT. Though ANSI/ANS-56.8 does not define clearly the minimum test duration for the make-up flow rate method, it requires obtaining the data after reaching the stable condition. Thus the prerequisite stable condition for data acquisition and the test period for type "C" LLRT is differently applied to each NPPs. Therefore, this study presents a unified test criteria for data stabilization and test duration through experiments to improve the test reliability for type "C".

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.11a
• /
• pp.369-375
• /
• 1996

가압경수로의 기동과 냉각시 발생할 수 있는 저온과압사고는 원자로 압력용기의 취성파괴를 유발할 위험이 있다. 따라서 발전소는 저온과압을 방지하기 위해 기술지침서의 온도-압력 곡선을 토대로 운전온도에 따른 압력경계를 제한하고 있으며, 과압방지설비로 가압기 PORV나 잔열제거계통의 방출밸브를 갖추고 있다. 미 NRC에서는 GL90-06을 통해 저온과압사고에 대한 안전성 분석을 권고하고 있으며, 이에 따른 표준 기술 지침서를 제시하였다. 국내 가동 원자력발전소중 영광 3,4호기 이후에는 설계시 이를 반영하였으나, 타 발전소에는 반영되질 않았다. 이 논문에서는 이들 운전중인 가압경수로의 저온과압사고에 대한 안전성 분석을 수행하기 위해 개발한 안전성 평가 방법을 제시하였다.

• Journal of the Korean Society of Safety
• /
• v.21 no.1 s.73
• /
• pp.48-52
• /
• 2006

This study is a research of safety valve development for LP gas cylinder which use sintering metal. Re-searcher wishes to apply technology of sintering metal for safety valve development and do gas flow control. The basis of this study is most suitable fluid examination that to reduce gas accident. This research concluded following results. 1. When press pin length is 42mm to 45mm powder quantity is 0.25g, in case of press pin length 36mm to 42mm powder quantity is 0.2g, displayed fluid optimization. 2. When press pin length is 39mm and powder quantity is 0.25g, press pressure displayed fluid optimization at all interests from $1.2\;tons/cm^{2}\;to\;2\;tons/cm^{2}$. 3. When apparent density is about $5.0g/cm^{3}\;to\;4.5g/cm^{3}$, fluid optimization becomes.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2010.04a
• /
• pp.141-146
• /
• 2010

특수선(FPSO, Drillship)의 거주구역이나, 대형 여객선(크루즈선) 공간의 70% 이상을 차지하는 수용시설(accommodation) 즉, 객실, 라운지, 공공장소, 창고 등은 24시간 사람이 상주하는 구역임으로 화재로부터 완벽하게 보호되어야 한다. 이를 위해 국제해사기구(IMO)에서는 SOLAS II-2 Reg. 10.6과 FSS code Ch. 8에 적합한 미분무수 소화설비를 설치할 것을 강제화하고 있다. 이러한 미분무수 소화설비는 미분무수 노즐, 압력용기, 섹션밸브, 펌프유닛 등으로 구성되는데 특히 핵심부품인 미분무수 노즐은 IMO Res. MSC 265(84)에 따라 노즐성능시험 및 화재진압성능시험을 통해 형식승인을 득해야 한다. 본 연구에서 이러한 기준에 만족하는 미분무수 노즐을 개발하고자 선실 및 복도에 대한 화재시험에 이어 공공장소 화재시험을 수행하였으며, 두 가지 천장 높이에 대한 화재진압성능을 평가하였다.

• Proceedings of the SAREK Conference
• /
• 2005.11a
• /
• pp.457-462
• /
• 2005

In this study, the performance of automatic thermostatic valves according to each heating method of a large scale residential building were researched by simulation. The flow characteristics of the entire pipe networks of the hot water radiant heating system is analized by using linear analysis method. For the analysis of unsteady heat transfer phenomena in each household, the method of using electric equivalent R-C circuit is applied.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05a
• /
• pp.771-776
• /
• 1998

울진 원전 3,4 호기를 대상으로 MAAP4.0.2 코드를 이용하여 발전소 정전사고를 모의/분석했다. 본 분석에서는 사고진행에 따른 일.이차계통의 상태변화를 원자로용기 파손때까지 상세 파악하였다. 사고관리 관점에서, 발전소 정전사고는 이차측의 대기방출밸브를 통한 강제감압에 의해 사고진행을 완화할 수 있으며 이러한 운전원 조치에 의한 완화효과를 검토하였다 그 결과 감압시작 2시간후에 일차측은 약 24$^{\circ}C$ 의 과냉각도를 보이며 안정되었고. 사고시작 1시간 후부터 3시간 동안의 강제감압이 성공한 경우, 노심노출시간 기준으로 약 2시간의 지면효과가 있었다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.7
• /
• pp.947-952
• /
• 2010

Components such as pressure vessel, hydraulic hose assembly, accumulator, hydraulic cylinder, hydraulic valve, pipe, etc., are tested under the impulse-pressure conditions prescribed in ISO and SAE standards. The impulse pressure test machine needs to have a high pressure, a precise control system and a long life. It should satisfy the requirements for fabrication of the impulse tester to generate ultra high pressure in the hydraulic system. In the impulse tester, a servo-valve control system is adopted; although the control application is convenient, it is expensive owing to the cost of developing the system. The type of the control system determines the pressure wave, which affects the components that are tested. In this study, the manufacturing process and the intensifier system design related to the flow, pressure, and the increasing rate of pressure are investigated. The results indicate the ultra high pressure waves in the system.