• Science of Emotion and Sensibility
• /
• v.9 no.2
• /
• pp.133-140
• /
• 2006

In order to investigate the sensation of the fabric sound simulating the real wear-condition, the fabric sound simulator using reciprocating friction was developed. Fabric sounds from 5 specimen were generated by the fabric sound simulator and recorded using high performance microphone. Physical sound parameters of fabrics including level pressure of total sound (LPT), level range (${\Delta}L$), and frequency differences (${\Delta}f$) were calculated. For psychological evaluation, seven adjectives for sound (softness, loudness, sharpness, clearness, roughness, highness, and pleasantness) were used as the semantic differential scale. Fabric sounds by reciprocating friction of nylon taffeta and polyester leno had the highest value of LPT and evaluated as loud, sharp, rough, and unpleasant while polyester ultra suede and silk crepe de chine haying the lower LPT and ${\Delta}f$ were perceived as soft and quite. Comparing with fabric sound by one-way friction, fabric sound by reciprocation friction was perceived as more sharp, loud, and rough. LPT was also the most important factor affecting the sensation of the fabric sound by reciprocating friction.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.7
• /
• pp.681-686
• /
• 2015

The onset characteristics of friction-induced noise for a steel plate and 4 metallic pins (Cu, Ni, Al, Mg) were studied through the pin-on-disk machine and the reciprocating testing machine. The results showed that the negative slope of the friction curve was related to the onset time of friction noise. Particularly, Cu was found to be the best metallic material for preventing squeak noise in terms of the onset time and the negative friction slope.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.5
• /
• pp.449-455
• /
• 2016

This study provides the finite-element (FE) squeal-model predicting friction-induced noise with respect to several friction materials that have different friction characteristics. The friction curve and the corresponding friction noise were measured for four friction materials (Cu, Ni, Al, Mg) using the pin-on-disk and reciprocating friction system. The slope of the friction curve linearized at the sliding velocity was applied to the FE model. The unstable modes in the complex eigenvalue analysis were shown to correspond to the squeal frequencies that existed in the experiment.

• Proceedings of the KWS Conference
• /
• 1993.05a
• /
• pp.25-26
• /
• 1993

• Tribology and Lubricants
• /
• v.26 no.4
• /
• pp.224-229
• /
• 2010

A new test rig is presented to measure friction losses at journal bearings in a reciprocating compressor. This rig consists of a test bearing, torque sensor, driving motor and loading parts especially for vertical shaft. Friction losses are obtained by measuring torque between motor and test bearing. The experiments are carried out at several rotational speeds and temperatures. The test results are presented and discussed.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.4
• /
• pp.332-338
• /
• 2014

Experimental study is conducted for investigating the characteristics of friction-induced noise with respect to the variation of system geometry. In this study, a vertically fixed rod is in contact with the reciprocating plate which is controlled by the step motor. Friction noise is generated during the reciprocating motion due to the frictional contact between the plastic pin and the aluminum plate. The frequencies of the friction noise are changed when the height of the rod varies. However, it is found that the vibration modes involved in the friction noise are not changed. It implies that the unstable modes remain unstable regardless of the change of the system geometry, and thus, there are the certain mode shapes which are likely to produce friction noise.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.3 s.174
• /
• pp.786-793
• /
• 2000

Nylon, Polyacetal and PTFE were studied to gain a better understanding of their tribological behavior. Wear tests were conducted with reciprocating motion under dry sliding conditions. Friction coefficient and specific wear rate were measured as a function of sliding distance. The worn surfaces were examined with a Scanning Electron Microscope(SEM). Polyacetal showed lowest specific wear rates and PTFE exhibited lowest friction coefficient. The dominant wear mechanism found were adhesion and abrasion.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.7
• /
• pp.640-644
• /
• 2013

The present study provides the characteristics of friction noise under reciprocating sliding. The friction contact is generated between the aluminum plate and plastic, which results in friction noise. The experimental results reveal that the friction noise under reciprocating sliding can be produced as the friction coefficient increases. It is also shown that the vibration modes of the pin with dominant deflection in the sliding direction is participated on the friction noise.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.12 no.11
• /
• pp.904-913
• /
• 2002

In this study, a dynamic analysis of the reciprocating compression mechanism considering viscous friction force of a piston used in small refrigeration compressors is performed. The length of cylinder in this class of compressors is shortening to diminish the frictional losses of the piston-cylinder system. So, the contacting length between piston and cylinder liner is in variable with the rotating crank angle around the BDC of the reciprocating piston. In the problem formulation of the compression mechanism dynamics, the change in bearing length of the piston and all corresponding viscous forces and moments are considered in order to determine the trajectories of piston and crankshaft. The piston orbits for viscous friction model and Coulomb friction model were used to compare the effect of the friction forces of piston on the dynamic trajectories of piston. To investigate the effect of friction force acting on the piston for the dynamic characteristics of crankshaft, comparison of the crankshaft loci is given in both viscous model and Coulomb model. Results show that the viscous friction force of piston must be considered in calculating for the accurate dynamic characteristics of the reciprocating compression mechanism.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.12
• /
• pp.1251-1256
• /
• 2015

This study investigates the friction noise characteristic in relation to the corrosion of metal by using the frictional reciprocating and pin-on-disk system. From the experiments, it is found that the corrosion of metal advances the onset time and increases the magnitude of friction noise. Further, it is observed that the effect of corrosion on friction noise stems from the alteration of tribo-surface during repetitive frictional motion. The alteration of the corrosive contact surface induces a negative friction-velocity slope, by which the corrosion of metal can generate dynamic instability faster than non-corrosion of metal.