• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.8
• /
• pp.1116-1122
• /
• 2008

The reciprocating type hydrogen compressor has a pulsation due to the reciprocative characteristics which results in noise and vibration. Snubber is installed for the relaxation of pulsation, but it causes reduction of compressor efficiency because of pressure loss. Five types of snubber were modeled for the numerical investigation of the effect of the relative position of inlet and outlet and buffer angle on the pulsation amplitude and pressure loss. MSC/NASTRAN is used as a numerical tool to identify the vibration characteristic of each type. Frequency responses in forced vibration mode are compared for various cases and buffer angles.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.8
• /
• pp.759-769
• /
• 2013

Electronic equipment has been applied to virtually every area associated with commercial, industrial, and military applications. Specifically, electronics have been incorporated into avionics components installed in aircraft. This equipment is exposed to dynamic loads such as vibration, shock, and acceleration. Especially, avionics components installed in a helicopter are subjected to simultaneous sine and random base excitations. These are denoted as sine on random vibrations according to MIL-STD-810F, Method 514.5. In the past, isolators have been applied to avionics components to reduce vibration and shock. However, an isolator applied to an avionics component installed in a helicopter can amplify the vibration magnitude, and damage the chassis, circuit card assembly, and the isolator itself via resonance at low-frequency sinusoidal vibrations. The objective of this study is to investigate the dynamic characteristics of an avionics component installed in a helicopter and the structural dynamic modification of its tray plate without an isolator using both a finite element analysis and experiments. The structure is optimized by dynamic loads that are selected by comparing the vibration, shock, and acceleration loads using vibration and shock response spectra. A finite element model(FEM) was constructed using a simplified geometry and valid element types that reflect the dynamic characteristics. The FEM was verified by an experimental modal analysis. Design parameters were extracted and selected to modify the structural dynamics using topology optimization, and design of experiments(DOE). A prototype of a modified model was constructed and its feasibility was evaluated using an FEM and a performance test.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.3
• /
• pp.58-64
• /
• 2003

Pogo is the instability resulting from the interaction between rocket structure and propulsion system of liquid propellant rocket. The coupling of structure and propulsion system can lead to severe problem in rocket. For the analysis of pogo, a time-invariant linearized mathematical model is developed for a selected flight time. Propulsion system is modeled using element representations for each components. Rocket structure is modeled using FEM. Form the results of modal analysis of structure, the behavior of structure can be represented. System equations for coupling structure and propulsion system are composed. The stability in obtained by the eigen solution of system matrix. The optimization of the design variables such as size, place of accumulator for suppressing pogo instability in carried out. This article of study can be used to determine the degree of stability, and guide the design of pogo suppression system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.53-56
• /
• 2007

The reciprocating type hydrogen compressor is occurred by the pulsation from the mechanism and this pulsation is make much noise and vibration. Therefor snubber is installed for pulsation decreasing. The five type snubber models were designed for increasing pulsation amplitude reduction and decreasing pressure loss in snubber considering output pipe location as design value. And the pressure flued analysis is carried by CFD. In this paper, each type snubber according CFD result are analyzed by the MSC/NASTRAN to identify the vibration characteristic of each type. The vibration results are compared with CFD results.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.23 no.7
• /
• pp.1817-1823
• /
• 1998

V.42bis, a type of LZW(Lempel-Ziv-Welch) code, is well-known as theinter national standard is asynchronous data compression. In this paper, we analyze several undesirable phenomena arising from the application of v.42bis to high speed data transmission, and we propose a modified technique to overcome them. the proposed technique determines the proper size of the dictionary, one of important factors affecting the compression ratio, and improves the method of dictionary generation for a higher compression ratio. Furthermore, we analyze the problem of excessive mode changes and solve it to a certain degree by adjusting the threshold for mode change. By doing this, we can achieve smiller variation of the compression ratio in time. This improvement chtributes to easier and better design and control of the buffer in high speed data transmission.

• Proceedings of the KAIS Fall Conference
• /
• 2011.05a
• /
• pp.151-154
• /
• 2011

$NO_x$ 제어 기술로는 크게 연소 전 탈질, 연소 개선 및 연소 후 탈질 기술로 구분할 수 있으며, 연소 후 탈질 기술에 속하는 SCR은 촉매를 사용하여 $NO_x$를 환원하는 대표적인 배연탈질기술이다. SCR의 $NO_x$ 저감 성능은 촉매 요인(촉매 구성물질, 형태, 공간속도 등)과 배가스의 온도, 유속 분포, 공정 운전 조건 등의 다양한 인자에 의해 좌우되는데 특히, 촉매층으로 유입되는 유동의 균일도는 가장 중요한 요소가 된다. 유동이 균일하지 않을 경우 촉매 전단에 편류가 발생하게 될 것이며 일정 촉매만 사용하게 되어 촉매 사용주기 감소 및 SCR 성능 저하를 초래할 수 있기 때문이다. 본 연구에서는 3차원 수치 해석 기법을 이용하여 설계 초기의 SCR 반응기 내 유동 특성을 모사하여 기류 균일도 여부를 확인하고, SCR 내 유동 균일도를 최적화시키기 위한 설계를 목적으로 설치하는 가이드 베인과 배플, 다공판이 반응기 내부 유동 및 촉매층의 기류 균일도에 미치는 영향에 대하여 연구를 수행하였다. 그 결과, 유동 개선을 위해 인입 덕트 곡관부에 가이드 베인을 설치하여 처리가스를 적절하게 배분시키고, 반응기 상단에 3단 배플을 설치한 결과 반응기 내부 유동의 편류 개선에 매우 효과적임을 알 수 있었다. 또한 다공판을 예비 촉매층 하단부 위치에 추가로 설치함에 따라 유동을 한번 더 완충시킬 수 있어 기류 균일도가 매우 양호해짐을 알 수 있었다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.10
• /
• pp.4666-4672
• /
• 2011

Performance of NOx removal in SCR(Selective Catalytic Reduction) process depends on such various factors as catalyst factors (catalyst composition, catalyst form, space velocity, etc.), temperature of exhaust gas, and velocity distribution of exhaust gas. Especially the flow uniformity of gas stream flowing into the catalyst layer is believed to be the most important factor to influence the performance. In this research, the flow characteristics of a SCR process at design stage was simulated, using 3-dimensional numerical analysis method, to confirm the uniformity of the gas stream. In addition, the effects of guide vanes, baffles, and perforated plates on the flow uniformity for the inside and catalyst layer of the reactor were studied in order to optimize the flow uniformity inside the SCR reactor. It was found that the installation of a guide vane at the inlet duct L-tube part and the installation of a baffle at the upper part is very effective in avoiding chaneling inside the reactor. It was also found that additional installation of a perforated plate at the lower part of the potential catalyst layer buffers once more the flow for very uniform distribution of the gas stream.

• Microbiology and Biotechnology Letters
• /
• v.9 no.1
• /
• pp.35-44
• /
• 1981

Whole cell penicillin amidase of Escherichia coli was immobilized by entrapment in gelatin followed by extrusion and crosslinking with glutaraldehyde. The immobilized engyme preparation demonstrated the recovery yield of activity up to 70% and good stability during storage and operation. The half life of activity decay during the operation was estimated to be about 50 days. The optimum pH and temperature for both of immobilized and soluble enzyme are 8.5 and 5$0^{\circ}C$, respectively. No significant change was demonstrated in the effect of pH and temperature, but the increase in heat stability at high temperature was observed in the case of the immobilized enzyme. It was found that the plug flow reactor could be operated favorably since the pH drop along the column path due to tile reaction product was minimized by employing substrate solution with moderate buffer strength. The optimal condition of reactor operation was discussed with regard to the effect of substrate concentration and the residence time on the conversion efficiency and productivity.

• The Journal of the Convergence on Culture Technology
• /
• v.8 no.6
• /
• pp.905-910
• /
• 2022

Drowsy driving requires a lot of social attention because it increases the incidence of traffic accidents and leads to fatal accidents. The number of accidents caused by drowsy driving is increasing every year. Therefore, in order to solve this problem all over the world, research for measuring various biosignals is being conducted. Among them, this paper focuses on non-contact biosignal analysis. Various noises such as engine, tire, and body vibrations are generated in a running vehicle. To measure the driver's heart rate and respiration rate in a driving vehicle with a piezoelectric sensor, a sensor plate that can cushion vehicle vibrations was designed and noise generated from the vehicle was reduced. In addition, we developed a system for classifying whether the driver is sleeping or not by extracting the model using the CNN-LSTM ensemble learning technique based on the signal of the piezoelectric sensor. In order to learn the sleep state, the subject's biosignals were acquired every 30 seconds, and 797 pieces of data were comparatively analyzed.

• Journal of Periodontal and Implant Science
• /
• v.33 no.1
• /
• pp.27-35
• /
• 2003

1. 목적 생체재료의 생체친화성을 증진시키고 치유를 촉진하기 위한 목적으로 생체재료의 생화학적 표면개질에 관한 연구가 널리 진행되고 있다. 이와 같은 목적으로 이용되어 온 부착분자에는 아미노산, 펩타이드, 단백질, 효소 및 성장인자들을 들 수 있으며, 이들 분자들을 금속, 골대체물질 및 폴리머와 같은 생체재료의 표면개질에 이용하여 왔다. 이 연구의 목적은 생체적합성이 우수하고 생분해성을 지닌 키토산으로 얇은 막을 제작한 후, 세포외 기질의 구성성분 중 세포부착에 관여하는 RGD 펩타이드를 부착시킨, 표면개질 키토산막의 생물학적 영향을 MG-63 조골양세포를 이용하여 관찰하는 것이다. 2. 방법 2% acetic acid에 키토산 가루를 녹여 만든 2% 키토산 용액으로 24-well 배양접시의 표면을 도포 후 24시간 동안 건조시켜 키토산막을 제작하였다. GRGDS 펩타이드를 cross-linker(EDC, NHS) (Sigma, MO, USA) 용액과 반응시켜서 펩타이드의 카르복실기를 활성화시켰다. 이들을 PBS 완충용액으로 수화시킨 키토산막과 결합시켜 펩타이드의 활성화된 카르복실기와 키토산의 아민기 간에 안정적인 아미드 결합(amide bond)이 형성되도록 하였다. 하루 동안 반응을 일으킨 후 PBS 완충용액과 증류수로 씻어내고 냉동 건조시킴으로써 GRGDS가 결합된 키토산막을 제작하였다. 재료 표면의 화학 성분을 알아보는데 사용되는 방법의 일종인 X-ray photoelectron spectroscopy(XPS) 분석을 통하여 부착분자가 키토산막에 결합된 여부를 확인하였다. GRGDS 펩타이드에 요오드를 결합시킨 후, 이것을 키토산막에 공유 결합시키고 XPS를 통해 요오드가 재료 표면에서 검출되는지를 검사하였다. 요오드가 검출된다면 이것은 키토산막 표면에 실제로 GRGDS 펩타이드가 존재하는 것을 의미하게 된다. 표면개질된 키토산막에 사람조골양세포인 MG-63을 접종하여 이를 실험군으로 하였고, 표면이 개질 되지 않은 키토산막을 대조군으로 하였다. 세포부착의 최적화 농도를 확인하기 위하여 GRGDS를 0.01, 0.05, 0.1, 0.25, 0.5, 1.0mg/ml의 농도로 준비하였다. 배양 후 1일, 7일째에 각 well에서 trypsin EDTA를 이용하여 세포를 분리한 후, 이를 원심 분리하여 세포수측정기를 이용하여 부착 세포의 수를 측정하여 세포의 부착 정도를 비교하였다. 배양 2시간, 24시간 후 주사전자현미경을 이용하여 키토산막에 부착된 세포의 양상을 관찰하였다. 3. 결과 XPS를 통한 표면의 화학 성분 분석 결과 GRGDS 펩타이드를 결합시킨 키토산막에서 요오드가 검출되었으며 펩타이드를 부착하지 않은 대조군에서는 검출되지 않았다. 따라서 cross-linker를 이용한 펩타이드와 키토산막의 공유결합을 확인할 수 있었다. 세포 배양 후 1일째 부착된 세포 수를 측정한 결과 0.1mg/ml 이상의 GRGDS 펩타이드 농도로 공유 결합시킨 키토산막에서 부착 세포 수가 다른 농도에 비해 유의성 있게 많이 관찰되었다. 이 농도 이하에서는 대조군과 실험군간에 세포부착의 유의한 차이가 없었다. 따라서 주사전자현미경을 이용한 부착 세포의 양상에 관한 관찰은 0.1mg/ml 농도의 펩타이드를 이용하였다. 세포 배양 7일째, 부착된 세포 수 측정 결과 GRGDS의 농도에 따른 유의성 있는 차이가 없었으며, 실험군과 대조군간에도 유의성 있는 차이가 없었다. 주사전자현미경 관찰결과 2시간 및 24시간 배양된 실험군 모두에서 별모양의 세포들이 키토산막 표면에 편평하게 잘 부착되어 있으며 많은 위족이 발달된 소견을 보인 반면, 대조군에서는 원형 또는 다각형 모양의 세포들이 실험군에 비해 부착이 덜 되어있는 양상을 보였다. 이 연구를 통하여 기능성 펩타이드를 생체재료의 표면에 공유결합 시키는 방법을 확립할 수 있었으며, RGD 펩타이드의 공유결합으로 표면개질된 키토산막이 조골세포의 부착능을 증진시킬 수 있음을 확인하였다. 표면개질된 생체재료를 소, 중동물에 적용시켜 생체 내에서의 생물학적 영향을 평가할 필요가 있으며, 이 실험의 결과는 향후 다양한 기능성 부착분자를 선발, 고안하여 임플란트용 생체재료의 표면개질에 이용하는 이른바 모방생체재료분야에 널리 활용될 수 있을 것으로 생각된다.