• Journal of the military operations research society of Korea
• /
• v.35 no.2
• /
• pp.33-49
• /
• 2009

The objective of this study is as follows. First, the hazard function on the failure probability density function of the K-1 tracked vehicles can be occurred in the form of the bathtub curve. Second, the failure mode may be different under two different operational situations. The research result shows that the bathtub curve can be fitted in the Weibull distribution, that assumes different shapes according to the specific stage of the system's life cycle. The K-1 tracked vehicle has a relatively high hazard(failure) rate at the time of its first service. The failure rate starts decreasing for a time immediately after it goes into service. After the break-in period, the surviving components have a fairly constant hazard rate. As the K-1 system ages, deterioration of its various parts takes place and the hazard rate starts Increasing. Second, the result shows the failure rate in the harsh operational environment is higher than that in the mild operational environment. In conclusion, the bathtub curve can be logically appropriate in establishing the depot overhaul cycle. Moreover, it is necessary for determining the right time of the depot overhaul to consider not only the age of defense equipment but also the different operational environment.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.78-78
• /
• 2004

기계 및 구조물의 설계시에는 허용응력 이하의 설계 조건으로 설계하지만 반복 작동을 하게 되는 기계 시스템의 경우에는 피로에 의한 파괴 현상이 나타나게 된다. 대부분의 기계 및 구조물은 사용시 변동 하중 상태에 놓이는 경우가 많게 되고 이로 인해 변동 응력이 작용되며 그 재료의 정적 강도보다 상당히 작은 간이라도 반복횟수가 증가함으로써 금속재료의 강도가 저하되어 결국 피로 파괴가 발생한다. 자동차, 항공기, 압축기, 펌프, 터빈 등과 같이 반복 작동을 하게 되는 기계 시스템에서 일어나는 파괴 현상 중에서 피로 파괴가 차지하는 비율이 점차 늘어나고 있다.(중략)

• Proceedings of the Korean Reliability Society Conference
• /
• 2002.06a
• /
• pp.199-204
• /
• 2002

본 연구에서는 저압 증기 터빈블레이드의 안전성 확보를 위하여 작용응력 및 강도의 변동성을 고려한 확률론적 해석을 수행하였다. 정상상태에서 작용응력은 이론 및 유한요소해석에 의해서 얻을 수 있으며, 최대 von-Mises 응력은 215.4MPa이다. 회전굽힘 하중하에서의 피로한도는 응력비 R= -1에서 계단식 시험법을 이용하여 구하였으며, 이의 확률론적 특성에 가장 적합한 분포는 3 모수 와이블 분포이다. 그리고 신뢰성에 미치는 다양한 인자들의 영향은 영향계수(sensitivity factor)를 이용하여 정량적으로 평가하였다.

• Journal of Korean Society of Water and Wastewater
• /
• v.34 no.4
• /
• pp.251-258
• /
• 2020

Sewer deterioration models are needed to forecast the remaining life expectancy of sewer networks by assessing their conditions. In this study, the serious defect (or condition state 3) occurrence probability, at which sewer rehabilitation program should be implemented, was evaluated using four probability distribution functions such as normal, lognormal, exponential, and Weibull distribution. A sample of 252 km of CCTV-inspected sewer pipe data in city Z was collected in the first place. Then the effective data (284 sewer sections of 8.15 km) with reliable information were extracted and classified into 3 groups considering the sub-catchment area, sewer material, and sewer pipe size. Anderson-Darling test was conducted to select the most fitted probability distribution of sewer defect occurrence as Weibull distribution. The shape parameters (β) and scale parameters (η) of Weibull distribution were estimated from the data set of 3 classified groups, including standard errors, 95% confidence intervals, and log-likelihood values. The plot of probability density function and cumulative distribution function were obtained using the estimated parameter values, which could be used to indicate the quantitative level of risk on occurrence of CS3. It was estimated that sewer data group 1, group 2, and group 3 has CS3 occurrence probability exceeding 50% at 13th-year, 11th-year, and 16th-year after the installation, respectively. For every data groups, the time exceeding the CS3 occurrence probability of 90% was also predicted to be 27th- to 30th-year after the installation.

• The Korean Journal of Applied Statistics
• /
• v.23 no.5
• /
• pp.943-953
• /
• 2010

From a mixture distribution of the score random variable for credit evaluation, there are many methods of estimating optimal thresholds. Most the research news is based on the assumption of normal distributions. In this paper, we extend non-normal distributions such as Weibull, Logistic and Gamma distributions to estimate an optimal threshold by using a hypotheses test method and other methods maximizing the total accuracy and the true rate. The type I and II errors are obtained and compared with their sums. Finally we discuss their e ciency and derive conclusions for non-normal distributions.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.9 s.180
• /
• pp.2353-2360
• /
• 2000

Statistical fatigue properties of metallic materials are increasingly required for reliability design purpose. In this study, static and fatigue tests were conducted and the normal, log-normal, two -parameter Weibull distributions at the 5% significance level are compared using the Kolmogorov-Smirnov goodness-of-fit test. Parameter estimation were compared with experimental results using the maximum likelihood method and least square method. It is found that two-parameter Weibull distribution and maximum likelihood method provide a good fit for static and fatigue life data. Therefore, it is applicable to the static and fatigue life analysis of the spheroidal graphite cast iron. The P-S-N curves were evaluated using log-normal distribution, which showed fatigue life behavior very well.

• Journal of Korea Water Resources Association
• /
• v.52 no.12
• /
• pp.1001-1009
• /
• 2019

Due to recent increasing heavy snow in Korea, the damage caused by heavy snow is also increasing. In Korea, there are many efforts including establishing disaster prevention measures to reduce the damage throughout the country, but it is difficult to establish the design criteria due to the characteristics of heavy snow. In this study, snowfall frequency analysis was performed to estimate design snow depths using observed snow depth data at Jinju, Changwon and Hapcheon stations. The conventional frequency analysis is sometime limted to apply to the snow depth data containing zero values which produce unrealistc estimates of distributon parameters. To overcome this problem, this study employed mixed distributions based on Lognormal, Generalized Pareto (GP), Generalized Extreme Value (GEV), Gamma, Gumbel and Weibull distribution. The results show that the mixed distributions produced smaller design snow depths than single distributions, which indicated that the mixed distributions are applicable and practical to estimate design snow depths.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.3
• /
• pp.251-257
• /
• 2011

This paper deals with the statistical properties of parameters B and q in the creep crack growth rate (CCGR) law, da/dt=B$(C^*)^q$, in Mod. 9Cr-1Mo (ASME Gr.91) steel which is considered a candidate materials for fabricating next generation nuclear reactors. The CCGR data were obtained by creep crack growth (CCG) tests performed on 1/2-inch compact tension (CT) specimens under an applied load of 5000N at a temperature of $600^{\circ}C$. The CCG behavior was analyzed statistically using the empirical equation between CCGR, da/dt and the creep fracture mechanics parameter, $C^*$. The B and q values were determined for each specimen by the least-squares fitting method. The probability distribution functions for B and q were investigated using normal, log-normal, and Weibull distributions. As far as this study is considered, it can be appeared that B and q followed the log-normal and Weibull distributions. Moreover, a strong positive linear correlation was found between B and q.

• Journal of the Microelectronics and Packaging Society
• /
• v.18 no.1
• /
• pp.15-21
• /
• 2011

In this study, flexural strength and fracture behavior of silicon die from single crystalline silicon wafer were investigated as a function of thickness. Silicon wafers with various thickness of 300, 200, 180, 160, 150, and 100 ${\mu}m$ were prepared by mechanical grinding and polishing of as-saw wafers. Flexural strength of 40 silicon dies (size: 62.5 mm${\times}$4 mm) from each wafer was measured by four point bending test, respectively. For statistical analysis of flexural strength, shape factor(i.e., Weibull modulus) and scale factor were determined from Weibull plot. Flexural strength reflecting both statistical fracture probability and size (thickness) effect of brittle silicon die was obtained as a linear function of die thickness. Fracture appearance was discussed in relation with measured fracture strength.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.6
• /
• pp.993-999
• /
• 2004

The estimation of fatigue life at the design stage of membrane type LNG tank is very important in order to arrive at feasible and cost effective solutions considering the total lifetime of the tank. In this study, the practical procedure of fatigue life prediction by use of cumulative damage factors based on Miner-Palmgren hypothesis and probability density function has been shown with the corner region of Gaz Transport Membrane type LNG tank being used as an example. In particular the parameters of Weibull distribution that determine the stress spectrum are discussed. The main results obtained from this study are as follows: 1. The recommended value for the shape parameter of Weibull distribution for the LNG tank is 1.1 in case of using the direct calculation method proposed in this study. 2. The calculated fatigue life is influenced by the shape parameter of Weibull distribution and stress block. The safe fatigue design can be achieved by using higher value of shape parameter and the stress blocks divided into more stress blocks.