• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.12
• /
• pp.1146-1151
• /
• 2008

In this paper, the effects of torsional flexibility on a flapping airfoil are investigated. The aerodynamic forces of a torsional flexible flapping airfoil is computed using 2-D unsteady vortex panel method. A typical-section aeroelastic model is used for the aeroelsatic calculation of the flapping airfoil. Torsional flexibility and excitation frequency are considered as main effective parameters. Under heavy airfoil condition , the thrust peak is observed at the points where the frequency ratio is about 0.75. Based on this peak criterion, there exists two different motions. One is an inertia driven deformation motion and the other is an oscillation driven deformation motion. Also, in the thrust peak condition, the phase angle is kept 85 degrees, independent of the torsional flexibility and the excitation frequency.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.11
• /
• pp.1080-1088
• /
• 2009

An actuator using piezoceramic material was designed in order to perform a flow control for flat plate flow. Boundary layer measurements were carried out to explore the flow disturbances by the designed actuator that was activated at low excitation frequency(15Hz). The mean velocity and fluctuation in the boundary layers were measured at $x/{\delta}^*=31.9$ downstream from the actuator tip by a one-dimensional hot-wire probe(55P14). Results reveal that low- and high-velocity regions were observed in the vicinity of the actuator center and in the outer area of the actuator respectively, and the formation of counter-rotating streamwise vortices was predicted. The fluctuations were persistently found in the outer part of the actuator and an inflection point in the spanwise gradient of the streamwise velocity was observed. Boundary layer instability was amplified at both the actuator excitation frequency and the T-S wave frequency when the actuator was excited at low frequency.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.8 s.227
• /
• pp.921-928
• /
• 2004

Measurements of local heat/mass transfer coefficients in rotating two-pass ducts are presented. Ducts of three different aspect ratios (W/H), 0.5, 1.0 and 2.0, are employed with a fixed hydraulic diameter ($D_h$) of 26.7 nm. $90^{\circ}$-rib turbulators are attached on the leading and trailing walls symmetrically. The rib height-to-hydraulic diameter ratio ($e/D_h$) is 0.056, and the rib pitch-to-rib height ratio (p/e) is 10. The experimental conditions are the same as those of the previous part of the study. As the rib height-to-duct height ratio (e/H) increases, the core flow is more disturbed and accelerated in the midsections of ribs. Therefore, the obtained data show higher heat/mass transfer in the higher aspect ratio duct. Dean vortices also augment heat/mass transfer in the turn and in the upstream region of the second pass. However, the effect becomes less significant for the higher aspect ratio because the surface area increases in the present geometric condition. The effect of rotation produces heat/mass transfer discrepancy.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.4 no.1 s.12
• /
• pp.15-24
• /
• 2004

Generally, a ${\pi}$-type girder composed of two I-type girders is known to have a significant disadvantage in wind resistance design because of aerodynamic instability. A representative bridge for this girder was Tacoma Narrows Bridge. Since Tacoma Narrows Bridge had very low stiffness of the bridge structure and its cross-section shape had aerodynamic instability, the bridge collapsed after severe torsion and vibration events in 19m/s wind speed. Aerodynamic vibration can be avoided by enhancing structural stiffness and damping factor and conducting a study of cross-section shapes. This study shows the angle of attack for the four-span cable stayed bridge having ${\pi}$-type cross-section and describes the aerodynamic characteristics of the changed cross-section with aerodynamic vibration damping additions, by carrying out two-dimension vibration tests. As a result of uniform flow and turbulent flow, the study shows that because the basic ${\pi}$-type cross-section alone can have efficient wind resistant stability, there is no need to have additional aerodynamic damping equipment. Since this four 230m-main-span bridge has a large frequency and also has a big stiffness compared to other bridges containing a similar cross-section, it has aerodynamic stability under the design wind speed.

• The Journal of the Acoustical Society of Korea
• /
• v.43 no.5
• /
• pp.557-569
• /
• 2024

Recently, the operating speed of pressure devices is increased for high performance. It lead to the increase of flow rate. Consequently, the results in the high relative contribution of flow borne noise to the noise from pipe. Analyzing the characteristics of flow-borne noise is essential for evaluating noise performance during the design stage of the piping system. Therefore, in this paper, the noise generation mechanism and transfer characteristic was numerically investigated. The wall pressure induced by the fluid moving through the orifice was predicted using the compressible Large Eddy Simulation (LES). The Wavenumber-Frequency Analysis (WFA) was employed to decompose the wall pressure into incompressible and compressible component, which are to cause Fluid Induced Vibration (FIV) and Acoustic Induced Vibration (AIV). The propagation and contribution characteristics were analyzed using the separated incompressible and compressible wall pressure components. Additionally, the correlation between these pressure components and the internal flow within the piping was investigated through flow field analysis, which elucidated the mechanisms and propagation characteristics of flow-induced noise. From these results, it was confirmed that the contribution of the incompressible wall pressure component was high near the noise source and that the contribution of the compressible wall pressure component increased as it propagated long distances upstream and downstream direction of the noise source.

• Journal of Korea Water Resources Association
• /
• v.36 no.5
• /
• pp.761-776
• /
• 2003

Numerical models were employed to investigate the hydrodynamics of water flow in the lake behind a dam and the spillway where supercritical flows and negative pressures are likely to occur. In this study, 2-D model, RMA2 was employed to examine the upstream flow pattern and 3-D CFD model, FLUENT was used to evaluate the three-dimensional flow in the approaching region and flow distributions in the spillways and discharge culverts. The bathymetry and the details of structures were carefully taken into consideration in building the models. The results from applying the 2-D model for the planned Hantan River Dam show that large eddies, the velocity of which reaches up to 1 m/s are occurring in several places upstream of the dam. That means that the 2-D numerical model could be utilized to investigate the two-dimensional flow patterns after the construction of a dam. Three-dimensional numerical results show that the approach flow varies depending on stages and discharge conditions, and velocities at spillways, discharge culverts, and sediment flushing tunnels are differently distributed. The velocity distributions obtained from the numerical model and a hydraulic model at the centerline of spillways 100 m upstream of the dam show reasonably similar results. It is expected that 2-D and 3-D numerical models ate useful tools to help optimize the dam design through investigating the flow patterns in the spillway and at the upstream of the dam, which is not always feasible in hydraulic modeling.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.6
• /
• pp.390-395
• /
• 2019

Hydrogymnastics so that sufficient exercise effect can be obtained using the resistance of water has a positive effect on patients who have to receive arthritis or rehabilitation treatment. However, the studies on the effect are insufficient, and the main cause of their effects has not been unclear yet. In this study, in order to identify the main cause of the effects of Hydrogymnastics, conducted Unsteady fluid flow simulation under the same conditions as the actual environment. The analysis model based on real hands, and the pressure fluctuation applied to the knuckle was analyzed by the computational fluid method. During the underwater movement of the hands, Various sizes of vortices were generated between fingers due to skin surface velocity and flow resistance. Pressure of about -500 Pa to +500 Pa is applied by the vortex flow. Also It was confirmed that the positive pressure and the negative pressure were continuously repeated up to maximum + 2000 Pa at the minimum of -2000 Pa at the portion where the direction was changed. Pressure fluctuations with a frequency of 20 Hz to 70 Hz were added continuously for each knuckle. These continuous pressure fluctuations provide a direct massage effect on the knuckles, an It is judged that the blood circulation at the relevant part is positively affected.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.8 s.227
• /
• pp.910-920
• /
• 2004

The heat/mass transfer characteristics in a rotating two-pass duct with and without rib turbulators are investigated in the present study. The square duct has a hydraulic diameter ($D_h$) of 26.7 mm, and $1.5\;mm{\times}1.5\;mm$ square $90^{\circ}$-rib turbulators are attached on the leading and trailing walls. The pitch-to-rib height ratio (p/e) is 10. The Reynolds number based on the hydraulic diameter is kept constant at 10,000 to exclude the Reynolds effect, and the rotation number is varied from 0.0 to 0.20. In the smooth duct, the curvature of the $180^{\circ}$-turn produces Dean vortices that enhance heat/mass transfer in the post-turn region. When rib turbulators are installed, heat/mass transfer is augmented 2.5 times higher than that of the smooth duct since the main flow is turbulated by reattaching and separating in the vicinity of the duct surfaces. The duct rotation results in heat/mass transfer discrepancy so that Sherwood number ratios are higher on the trailing surface in the first-pass and on the leading surface in the second-pass. In the turning region, Dean vortices shown in the stationary case transform into one large asymmetric vortex cell, and subsequent heat/mass transfer characteristics also change. As the rotation number increases, the heat/mass transfer discrepancy enlarges.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.3
• /
• pp.1-7
• /
• 2002

An experimental study was conducted to investigate the effects of leading edge extension(LEX) on the surface prssure distribution over a delta wing in a subsonic wind tunnel. Freestream velocity was 40m/sec and Reynolds number per meter was 1.7x$10^6$ with total pressure of 101Pa and total temperature of 278K. LEX changed the surface pressure distribution on the wing dramatically. Comparing with the results without LEX, the peak of pressure distribution decreased on the front chordwise location but it turned to increase on the rear chordwise location with increase of the angle of attaci. The spanwise gradient of the pressure distribution also increased in the rear chordwise location. Without LEX, the peak of pressure distribution increased and decreased irregularly with increase of the angle of attack at each chordwise location, but LEX made it increased almost linearly with increase of the angle of attack at all of the chordwise locations.

• 유체기계공업학회:학술대회논문집
• /
• 2006.08a
• /
• pp.327-330
• /
• 2006

This paper represents the numerical analysis on effects of radius ratio in a concentric annulus with a rotating inner cylinder. The numerical model consisted of two cylinder which inner cylinder is rotating and outer cylinder is fix, and the axial direction is used the cyclic condition because of the length for axial direction is assumed infinite. The diameter of inner cylinder is assumed 86.8mm, the numerical parameters are angular velocity and radius ratio. Also, the whole walls of numerical model have no-slip and the working fluid is used water at $20^{\circ}C$. The numerical analysis is assumed the transient state to observe the flow variations by time and the 3-D cylindrical coordinate system. The calculation grid adopted a non-constant grid for dense arrangement near the wall side of cylinder, the standard $k-{\omega}$ high Reynolds number model to consider the effect of turbulence flow and wall, the fully implicit method for time term and the quick scheme for momentum equation. The numerical method is compared with the experimental results by Wereley and Lueptow, and the results are very good agreement. As the results, TVF isn't appeared when Re is small because of the initial flow instability is disappear by effect of the centrifugal force and viscosity. The vortex size is from 0.8 to 1.1 for TVF at various $\eta$, and the traveling distance for wavy vortex have the critical traveling distance for each case.