• Applied Chemistry for Engineering
• /
• v.9 no.4
• /
• pp.554-560
• /
• 1998

Vinylbenzyl triphenyl phosphonium chloride(VTPC)/styrenes=3.7 copolymer was prepared for the moisture-absorptive polyelectrolyte dew sensor containing phosphonium salts. The humid membrane was fabricated on the gold/alumina electrode by dipping. The impedances were $11M{\Omega}$, $980k{\Omega}$, $50k{\Omega}$, and $11k{\Omega}$ at 70%RH, 80%RH, 90%RH and 95%RH, respectively, at $25^{\circ}C$ and the humidity-sensitive charactristic was suitable for the dew sensor. The temperature-dependent coefficient between $15^{\circ}C$ and $35^{\circ}C$ was found to be $-0.25%RH/^{\circ}C$ and the hysteresis falled in the ${\pm}2%RH$ range. The response time was found to be 45 sec for the relative humidity ranging from 70%RH to 98%RH at $25^{\circ}C$. The reliabilities such as temperature cycle, humidity cycle, high temperature and humidity resistance, electrical load stability, stability of long-term storage and water durability were measured and evaluated for the application as a dew sensor.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.9
• /
• pp.261-268
• /
• 2018

The use of electric cable was limited due to the installation time and large space as the increase of power demand and load quantity in side line. In order to solve these problems, the application of busway system which can supply the large current was increasing. But it was lack of methods of performance tests to evaluate the reliability and results of test for busway system. In this paper, we presented items to evaluate the reliability test for epoxy coated busway system with reference to IEC 61349-6. In addition, we proposed items to evaluate the reliability and long term life cycle test for the epoxy coated busway system. The combined acceleration deterioration test that reflects actual conditions of the survey as much as possible was conducted considering both thermal and electrical stresses. The deterioration condition was selected to satisfy fifty years life expectation and the insulation performance verification test of the busway system confirmed the long term life prediction. Furthermore, as test items for reliability assessment of compliance with the environment for the use of temperature, humidity and load current where busway system was installed, thermal overload test, water immersion test, cold shock temperature test and thermal cycle test were performed. And we examined changes in characteristics and abnormality after tests. From results, the test items presented to evaluate performance and reliability of the epoxy insulated busway system were confirmed to be appropriate in this paper, and the performance of the product was also confirmed to be excellent for reliability tests.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.3
• /
• pp.225-230
• /
• 2016

Fiber Bragg grating (FBG) sensors are currently the most prevalent sensors because of their unique advantages such as ease of multiplexing and capability of performing absolute measurements. They are applied to various structures for structural health monitoring (SHM). The signal characteristics of FBG sensors under thermal loading should be investigated to enhance the reliability of these sensors, because they are exposed to certain cyclic thermal loads due to temperature changes resulting from change of seasons, when they are applied to structures for SHM. In this study, tests on specimens are conducted in a thermal chamber with temperature changes from -$20^{\circ}C$ to $60^{\circ}C$ for 300 cycles. For the specimens, two types of base materials and adhesives that are normally used in the manufacture of packaged FBG sensors are selected. From the test results, it is confirmed that the FBG sensors undergo some degree of compressive strain under cyclic thermal load; this can lead to measurement errors. Hence, a pre-calibration is necessary before applying these sensors to structures for long-term SHM.

• Proceedings of the KIPE Conference
• /
• 2013.11a
• /
• pp.60-62
• /
• 2013

기본적으로 많은 인자들에 의해 영향을 받는 배터리 시스템은 일반적으로 사용 용도에 따라 단위 배터리 셀을 직렬 또는 병렬로 연결하여 하나의 배터리 모듈을 형성하고 있다. 다수개의 단위 배터리 셀을 연결하여 하나의 배터리 모듈로 사용하는 경우, 개별 셀의 활물질 및 전해액의 미소 변동, 충방전 사이클 차이, 온도의 영향에 따라 배터리 특성이 다르게 나타난다. 이러한 특성으로 인해 충전 및 방전이 진행됨에 따라 셀간의 전압 불균형 현상이 발생하고 이로 인해 배터리 수명은 급격하게 감소하여 배터리 교체와 같은 경제적 손실을 초래한다. 본 논문에서는 배터리의 성능과 안전성을 확보하기 위해 배터리 밸런싱에 관한 연구를 수행하였다. 기존의 수동적 밸런싱의 단점을 보완한 능동적 밸런싱을 사용하였고 제안한 회로의 기능 및 성능의 검증을 위해 배터리 관리 장치 보드를 설계 및 제작하여 시험한 결과 개선된 기능이 원활히 수행됨을 확인하였다.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.04a
• /
• pp.25-30
• /
• 2011

In this paper, we analyzed the electrical characteristics with Micro-cracks in Photovoltaic module. Micro cracks are increasing the breakage risk over the whole value chine from the wafer to the finished module, because the wafer or cell is exposed to mechanical stress. And The solar cells have to with stand the stress under out door operation in the finished module. Here the mechanical stress is induced by temperature changes and mechanical loads from wind and snow. So, we experimentally analyze the direct impact of micro-cracks on the module power and the consequences after artificial aging. The first step, we made micro-cracks in PV module by mechanical load test according to IEC 61215. Next, PV modules applied the thermal cycling test, because micro-cracks accelerated aging by thermal cycling test, according to IEC61215. Before every test, we checked output and EL image of PV module. As the result of first step, we detected little power loss(0.9%). But after thermal cycling test increased power loss about 3.2%.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.6
• /
• pp.403-410
• /
• 2020

This paper focuses on the design of a 12-kW small-scale supercritical CO₂ test loop. A theoretical study, stabilization, and optimization of carbon dioxide were carried out with the application of a solar heat source based on solar thermal data in Pohang. The thermodynamic cycle of the test facility is a Rankine cycle (transcritical cycle), which contains liquid, gas, and supercritical CO₂. The system is designed to achieve 6.98% efficiency at a maximum pressure of 12 MPa and a maximum temperature of 70℃. In addition, the optimum turbine inlet temperature and pressure were calculated to increase the cycle efficiency, and the application of an internal heat exchanger (IHX) was simulated. It was found that the maximum efficiency increases to 18.75%. The simulation confirmed that the efficiency of the cycle is 6.7% in May and 6.26% in June.

• Composites Research
• /
• v.33 no.2
• /
• pp.44-49
• /
• 2020

The cure kinetics of carbon fiber-reinforced prepreg for Vacuum Bag Only(VBO) process was studied by differential scanning calorimetry (DSC). The total heat of reaction (ΔH_total = 537.1 J/g) was defined by the dynamic scanning test using prepregs and isothermal scanning tests were performed at 130℃~180℃. The test results of isothermal scanning were observed that the heat of reaction was increased as the temperature elevated. The Kratz model was applied to analyze the cure kinetics of resin based on the test results. To verify the simulation model, the degree of cure from panels using different cure cycles were compared with the measurement. The simulation model showed that the error against the experimental value was less than 3.4%.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.2
• /
• pp.140-149
• /
• 1985

Fully reversed push-pull low cycle fatigue tests under strain control of trapezoid cyclic mode have been conducted in air at temperature of 550.deg. C and with frequency of 0.5 cpm on the domestic stainless steel STS 316 after solution treatment for 1 hour at 1100.deg. C. As an experimental equipment for high temperature fatigue tests, an electric servo-hydraulic fatigue machine(Instron model 1350) was used. This paper presents the effects of creep hold time and plastic strain range on push-pull high temperature low cycle fatigue life and fracture behavior. The fracture surfaces were observed by means of the scanning electron microscope. The results are as follows. (1) The fatigue life decreases with increase of the plastic strain range equal hold time and also decreases as the hold time is getting longer. (2) The frequency modified damage function can predict fatigue life by incorporating a variation of Coffin's frequency modified approach into damage function. (3) The ratios of creep damage and fatigue damage can be calculated by using he linear accumulation damage concept and the ratio of creep damage increases as the hold time is getting longer. (4) At the creep hold time of 5 minutes and the strain range of 2.0%, the fracture mode was intergranular fracture and striations were hardly observed. In this case, the intergranular cracking was originated in void type('.gamma.' type) cracking.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.310-310
• /
• 2012

최근 전자산업의 발달에 따른 전자제품의 소형화 및 고기능화 요구에 대응하기 위하여 저항(resistor), 커패시터(capacitor), IC (integrated circuit) 등의 수동소자를 개별 칩(discrete chip) 형태로 형성하여 기판의 표면에 실장하는 기술이 일반화되고 있다. 그러나, 수동 소자의 내장 기술은 기판의 패턴 밀도의 급격한 향상과 더불어 수동소자의 내장 공간도 협소해지는 문제점이 있다. 상기의 문제점을 해결하기 위해 개별 칩 형태의 내장형 저항체를 박막 형태의 내장 저항체를 구현하는 기술의 개발이 최근 주목을 받고 있다. 박막 저항체는 기존의 권선저항 및 후막저항과 비교하여 정밀한 온도저항계수를 가지며 이동통신에 적용시 고주파 영역(GHz)에서의 안정성과 주파수 특성이 좋다는 장점들을 가지고 있다. 박막 저항 물질로는 높은 경도와 우수한 열적 안정성을 가지고 있는 TaN (tantalum nitride)이 주로 사용되고 있다. 일반적으로, TaN 박막은 스퍼터링을 사용하며 제조되며 TaN 박막의 성질은 탄탈륨과 질소의 화학정량비, 박막의 결함 정도, 또는 공정압력 및 증착 온도, 플라즈마 파워 등과 같은 공정조건 등의 변화에 민감하게 변화하므로, TaN 박막의 다양한 연구가 더 필요한 실정이다. 본 연구에서는 반응성 마크네트론 스퍼터링을 사용하여 TaN 박막을 Si 기판 위에 증착하였고 TaN 박막의 원하는 특성을 제어할 수 있도록 질소 분압과 total gas volume을 조절하여 공정을 최적화하는 연구를 진행하였다. 또한 tensile pull-off 방법을 이용하여 TaN 박막의 부착강도를 평가하였고, 온도 사이클 및 고온고습 환경에 노출된 TaN 박막들의 열화 특성들에 대하여 연구하였다.

• Aerospace Engineering and Technology
• /
• v.13 no.1
• /
• pp.63-69
• /
• 2014

The oxidizer-rich preburner's combustion tests were fulfilled in the development process of staged combustion cycle rocket engines. The exhaust plume from an oxidizer-rich preburner is relatively transparent because combustion takes place in oxidizer rich state. During hot fire tests a still and infrared images were captured to visualize the plume structure, temperature distribution and so on. In addition, the exhaust plume was numerically investigated to figure out the detailed characteristics. The combustion was not considered for the numerical modeling, but the mixing of exhaust plume with circumstantial air was modeled by species transport model with several turbulence models. The inner structure of plume was configured out by the comparison of numerical results with experimental results, and the validity of applied numerical models was verified.