• Journal of the Korean Society of Food Science and Nutrition
• /
• v.34 no.3
• /
• pp.414-419
• /
• 2005

Newly harvested milled rice and stored milled rice for 2 years were steeped at the elevated temperatures of 40, 50, and 60℃ for 2hr, and physicochemical properties of the wet-milled rice flour were investigated. The lightness of rice flour was slightly higher in the newly harvested milled-rice, while yellowness was higher in the stored milled rice. For both newly harvested and stored milled rice, WAI, WSI, and gel consistency increased as steeping temperature increased. The amylograph pasting properties indicated that increasing steeping temperature increased peak viscosity. The differential scanning calorimetry (DSC) results of the rice flour showed that increasing steeping temperature increased onset and peak temperatures, with reduced gelatinization enthalphy, suggesting partial annealing occured. Particle size of rice flour from newly harvested milled rice was larger than that from stored milled rice.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.4
• /
• pp.1059-1066
• /
• 2008

Characteristics of pyrolysis and liquid product distribution of ABS plastics have been studied in the thermogravimetric(TG) reactor and bomb microreactor. Pyrolysis reactions were performed at temperature $400\sim450^{\circ}C$ and yield of each pyrolytic product was obtained by the weight measurement method. The molecular weight distributions of liquid products were determined by the GC-SIMDIS method. It was observed that solid residue which could not be detected in the thermogravimetric experiments was significantly formed in the batch-type microreactor. It was found that the yield and average molecular weight of liquid products were decreased with the increase of reaction temperature and time. but the formation of styrene monomer was significantly increased. The chain-end scission rate parameters were determined to be 54.1kcal/mole far ABS by the Arrhenius plot.

• Korean journal of food and cookery science
• /
• v.18 no.2
• /
• pp.200-205
• /
• 2002

Corn starch was modified by the oxidation with sodium hypochlorite(NaOCl) and the changes in the distribution of molecular weight were examined. Corn starch was oxidized with 0.25, 0.5, 0.75, 1.0, and 1.5% active Cl/g of starch at pH 7.0 and 25$^{\circ}C$ for 10 min. Oxidation of corn starch caused a change in the molecular weight distribution of amylopectin. The fraction of highest molecular weight in native starch decreased gradually and the fraction of lower molecular weight increased with increasing oxidation. Also, λ$\sub$max/ and iodine binding capacities of oxidized starches decreased and the soluble carbohydrate content increased by oxidation. The differential scanning calorimetric results of oxidized starches showed that the temperature and enthalpies of gelatinization were not changed by oxidation; however, the more the starch was oxidized, the greater the extent of retrogradation.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 2004.03a
• /
• pp.593-598
• /
• 2004

본 연구에서는 위성영상자료 Landsat TM(1999.8.16), ETM+(2002.9.17)을 활용하여 북한 서한만 지역의 NDVI, 토지피복, 지표온도 분포도를 작성하여 경년에 따른 환경변화를 탐지 및 분석하였으며 ISODATA Clustering 기법을 적용하여 북한 서한만 일대의 간석지 분포도를 작성하였다. 북한 서해안 간석지 면적변화 탐지를 위하여 고지형도 (1918)를 디지털 자료로 변환하여 북한 서해안 전역의 간석지 GIS DB를 구축하였으며 위성영상자료를 이용하여 작성된 간석지 공간 분포도와의 비교ㆍ분석을 통하여 북한 서한만 일대의 84년간의 간석지 면적변화를 탐지하였다. 이러한 연구 결과를 바탕으로 북한 서해안 지역의 간석지 퇴적 환경정보 및 다양한 연안 환경정보를 구축할 수 있었으며 북한 서해안 지역과 남한 서해안 지역의 간석지 연안환경 비교 분석 등을 위한 기초자료로 활용될 것으로 판단된다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.14 no.2
• /
• pp.68-72
• /
• 2004

Sm-doped YBCO high $T_c$ superconductor was directionally grown by zone melt growth process in air atmosphere. Cylindrical green rods of $(Sm/Y)_{1.8}Ba_{2.4}Cu_{3.4}O_{7-x}$[(Sm/Y)1.8] oxides were fabricated by cold isostatic pressing (CIP) method using rubber mold. Based on the variation of melting temperature and growth rate, the microstructure and superconducting properties were systematically measured by using optical micrographs, TEM and SQUID magnetometer. In this study optimum melting temperature and growth rate were $1085^{\circ}C$ and 3.5 mm/hr respectively. Nonsuperconducting $(Sm/Y)_2BaCuO_5$ inclusions of (Sm/Y)1.8 superconductor were uniformly distributed within the superconducting (Sm/Y) $Ba_2Cu_3O^{7-x}$ matrix. The directionally melt-textured (Sm/Y)1.8 superconductor showed an onset $T_c$ $\geq$ 90K and sharp superconducting transition.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.4
• /
• pp.361-369
• /
• 2011

The effect of an increase in the temperature of inlet air on the performance of a membrane humidifier for a PEMFC (Polymer Electrolyte Membrane Fuel Cell) vehicle was investigated both experimentally and numerically. A shell-and-tube type gas-to-gas humidifier with Nafion membrane was tested. The experimental result showed that water transfer varies nonlinearly with the temperature elevation. Numerical analysis based on detailed modeling was also conducted in simplified geometry of a single tube to explain this nonlinear behavior. The simulation revealed that the local water flux varies nonlinearly and dramatically along the tube. The analysis was based on the inverse relationship between the increase in temperature and decrease in relative humidity, both of which seriously affect the water conductivity of the membrane.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.4
• /
• pp.484-489
• /
• 2012

The objective of this work presented here was focused on analysis of particulate matter and nitrogen oxide characteristics in ESC test mode from heavy-duty diesel engine installed on-road vehicles applicable to prime propulsion engine for marine vessels. The authors confirmed that a large quantity particulate matter were emitted in high power density condition, nitrogen oxide characteristics were dependent on exhaust gas temperature. Particulate matters were reduced by 1/100~1/1,000 times in post DPF with test modes but filtration efficiency was decreased in the engine power fluctuation. In the case of the high speed and power condition, the exhaust level of particulate matters was increased according to increment of temperature of gas flowing into DPF. The orders of magnitude for particle concentration levels from the analysis of size distribution of particulate matters of test engine was different. Both emitting nano-sized particles below 100nm regardless of DPF and non-DPF.

• Korean Journal of Optics and Photonics
• /
• v.20 no.2
• /
• pp.110-117
• /
• 2009

This work introduces the uncertainty evaluation formulation on color measurement of light sources and display devices, such as CIE 1931 (x, y) chromaticity, CIE 1960 (u, v) chromaticity, correlated color temperature, and distribution temperature. All the mentioned quantities are reduced from spectral data in the visible range, for which uncertainties are strongly correlated between different wavelengths. Using matrix algebra we have formulated the uncertainty propagation from the SI- traceable spectral irradiance standard to the individual color related measurement quantities taking the correlation between wavelengths into account. As a result, we have demonstrated uncertainty evaluation examples of 3 types of light sources: CIE illuminant A, LED white light, and LCD white light. This method can be applied to any other quantities based on spectral measurement such as solar irradiance, material color measurement, etc.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.264-264
• /
• 2022

하천의 합류부는 두 개 이상의 하천이 하나로 합쳐지는 구간으로 서로 다른 특성으로 인해 급격한 흐름의 변화와 수리학적 지형변화가 발생하는 구간이다. 하천의 합류부에서는 유체의 물리화학적인 특성과 흐름 구조의 변화가 발생할 수 있다. 흐름 구조의 변화로 인한 유사 이송으로 세굴과 같은 지형적인 변화가 발생할 수 있다. 합류부의 혼합을 이해하기 위해서는 본류와 지류의 다양한 유입조건에 따른 공간적인 패턴을 분석하는 것이 중요하다. 그러나, 대부분의 합류부 연구들은 실측에 기반한 공간적인 패턴 분석의 어려움으로 인해 실내실험 또는 수치모형에 의존하여 연구가 수행되어, 실측자료에 기반한 공간적인 수체혼합의 분석은 매우 제한적이었다. 따라서, 본 연구에서는 하천 합류부의 혼합 현상을 규명하는 인자로 흐름 방향 유속, 2차류와 수심 등 기본적인 수리학적 인자들 외에 연직, 수평 방향으로 측정한 수질 자료와 드론 영상을 활용하여 합류부의 혼합 특성을 해석하고자 하였다. 수질 자료 중 하천의 혼합을 가장 잘 확인할 수 있는 인자로써 전기전도도와 온도를 활용하였다. SonTek ADCP를 이동식으로 횡단하여 측정해 흐름 방향 유속과 2차류, 수심을 확인하였다. ADCP를 운용함과 동시에 YSI의 수질센서를 활용하여 연직, 수평 방향으로의 전기전도도와 온도의 분포를 확인하였다. 또한, 합류부의 2차원 공간적인 분포를 확인하기 위해 드론 영상을 촬영하였다. ADCP, YSI, 드론의 계측자료는 한국의 낙동강과 남강 합류부에서 측정되었고, 분석 결과 계측장비 간의 경향성이 일치하였다. 또한, 이전에 진행된 해외의 합류부 연구 결과와 유사한 결과가 관측되었으나, 일부 부분에서는 다른 결과를 보였다.

• Solar Energy
• /
• v.16 no.2
• /
• pp.65-77
• /
• 1996

The operating thermal chracteristics of direct contact liquid-ice heat exchanger was experimentally investigated. In this paper, The effects of Ice Packing Factor(IPF), the inlet temperature and the flow rate of Heat Transfer Fluid(HTF) were stuided in the liquid-ice heat exchanger. Thermal stratification in liquid-ice heat exchanger was established clearly and faster at the higher inlet temperature and flow rate of HTF. At the end of melting of the lower flow rate is cleared the thermal stratification in liquid-ice heat exchanger. The temperature stratification is long with higher value of IPF of liquid-ice heat exchanger. The mean temperature of liquid-ice storage was changed rapidly with increasing flow rate and inlet temperature of HTF. The gradiant of ratio of total energy to latent energy was found higher with increasing inlet temperature and flow rate.