• Journal of the Korean Geosynthetics Society
• /
• v.16 no.2
• /
• pp.159-164
• /
• 2017

This paper presents the results of an investigation into the thermo-hydromechanical response of weathered granite soil. The effect of forced change temperature and relative humidity at the soil layer boundaries were monitored during heating. A series of load settlement test were performed on layers of compacted, unsatureated weathered granite soil with geosynthetic embedded at mid height before and after application of heat exchanger to the base of the soil layers. The results from this study indicated the potential for using embedded heat exchangers for the mechanical improvement of geotechnical systems incorporating weathered granite soil.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.11 no.4
• /
• pp.79-89
• /
• 2003

The purpose of this study is to investigate appropriate environmental factors when domestic waste is decomposed as aerobic digestion. So stabilization degree was measured after the waste is mixed as certain rates and water content was controlled by 55% and 60%. Variation of VS showed food waste in reactors of number 1, 2, 3, 4 and 5 was decomposed fully except reactor of number 6. Decomposition degree of VS in reactors of number 1, 2, 3 and 4 was not different high because Vinyl and plastic inserted played role bulking agent in reactor number 1, 2, 3 and 4. In reactors, maximum temperature indicated $57{\sim}59^{\circ}C$ and temperatures in reactors 1, 2, 3 and 4 were higher and remained longer than in reactor 5 and 6 for 2~4 days. Variation of $CO_2$ was similar to that of VS. The reduction rate of water content was low because moisture generated by oxidation fever of microorganism did not evaporated well. pH was low in the beginning of the reaction however, as time passed, it increased slightly and remained regular pattern. EC and C/N showed the same pattern as pH. Settlement and weight reduction rates were similar to the factors above. Reactor 1, 2, 3, and 4 showed higher settlement and weight reduction rate than reactor 5 and 6.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.27 no.12
• /
• pp.1368-1373
• /
• 2003

본 연구에서는 견직물에 강경한 촉감을 부여하여 한복지 뿐만 아니라 현대의 패션경향에도 부합되는 소재를 개발하고자 하였다. 견직물에 강경성을 부여하기 위하여 의마가공용 폴리우레탄 수지를 이용하여 수지농도와 큐어링온도에 따른 수지부착율을 조사하였고, 여기에 수반되는 물리적 특성의 변화를 살펴보았다. 또한 가공된 견직물의 세탁에 대한 내구성도 살펴보아 동시에 실용가능성도 검토하였다. 이상의 연구를 통해 다음과 같은 결과를 얻었다. 1. 의마가공용 폴리우레탄 수지를 견직물에 처리할 경우 수지 농도가 증가할수록 수지 부착량이 증가하였다. 2. 열처리온도를 변화시켜 수지부착량의 변화를 살펴본 결과 열처리 온도가 증가할수록 수지의 부착량이 감소하여 본 실험에 사용된 수지의 적정 열처리 온도가 160-18$0^{\circ}C$인 것을 고려해 볼 때 견직물의 경우 17$0^{\circ}C$의 열처리 온도가 적절한 것으로 나타났다. 3. 수지 처리된 견직물의 역학적 특성치의 변화를 살펴본 결과 RT, EM, MIU값은 감소하는 경향을 가지며, LT, B, 2HB, G, 2HG, 2HG5값은 증가하는 경향을 나타내어 폴리우레탄 수지처리로 의마가공 효과를 갖는 견직물을 얻을 수 있었다. 4. 수지 처리된 견직물의 역학적 특성치는 물세탁 후에도 크게 변화가 없어 세탁에 대한 내구성을 지니고 있는 것으로 나타났다.

• Journal of dental hygiene science
• /
• v.10 no.6
• /
• pp.459-464
• /
• 2010

The purpose of this study was to evaluate the physical properties of hydrophilic polyvinyl siloxane impression materials as change of material's storage temperatures. Working time, strain-in-compression, elastic recovery and consistency were tested according to ISO Standard NO. 1563. The results are as followed. 1. Working time decreased in cold storage. 2. Strain-in-compression was different in storage temperatures. Material's strain-in compression in cold temperatures were higher than in room temperature and in incubator. 3. A coefficient of elastic recovery varied by storage temperatures. The rate in cold temperature was the lowest and in incubator was the highest. 4. Consistency of impression substance different in storage temperatures. The extent in cold temperature is the highest and in incubator was the lowest. Statistical analysis(SPSS 14.0k, p>0.05) showed that storage temperature affect to material's physical properties. We recognized that the physical properties of polyvinyl siloxane impression materials were changed according to storage temperature.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.38-38
• /
• 1999

KSTAR(Korea Superconducting Tokamak Advanced Research) 핵융합 실험 장치의 진공용기 및 진공용기 내부의 플라즈마 대향 부품들은 초고진공 (5$\times$10-9 Torr)의 달성을 위해 진공용기 내부의 이물질(H2, H2O, CO, CO2, CH4 등) 제거를 목적으로 SS316LN인 진공용기는 25$0^{\circ}C$, 탄소 물질인 플라즈마 대향부품은 35$0^{\circ}C$ 정도까지 가열(이하 베이킹)할 필요성이 있다. 이 가열방법으로 고온 질소가스를 진공용기 이중벽 사이로 흘려주는 방식과 코일에 저주파 교류전류를 흘려 진공용기를 유도가열하는 방식이 고려되고 있는데, 유도가열방식은 최대 유도 전력이 70kW 정도로 실제 베이킹에 필요한 열량을 공급하는데 있어 적잖이 부족하며 또 국부적인 가열 특성으로 인하여 KSTSR의 베이킹 방식은 전자의 가열방식을 우선적으로 채택하고 있다. 본 논문에서는 0-차원 해석을 통하여 진공용기와 플라즈마 대향 부품들에 대한 베이킹 계획을 결정하고 이를 만족시키기 위해 투입해야 할 열량을 직선적으로 증가하는 온도 곡선에서 각 부분의 온도 상승률을 다르게 설정한 세 경우와 F-자 형태로 변화하는 온도 곡선의 경우에 대해 각각 적용하여 시간에 따른 필요열량을 비교.검토하였으며, 이를 근거로 안정적인 베이킹 계획을 선정하였고 이 베이킹 계획의 실현을 위해 투입해야 할 고온 질소가스의 유량과 온도 도달시간까지 매 시간에서의 가스온도를 산출하였다. 토러스 형상의 토카막 진공용기와 플라즈마 대향 부품 및 다층단열재에 대한 해석 모델은 길이가 유한한 0-차원 실린더 모델로 가정하였고, 이에 대한 기하학적 성질 및 열역학적 성질은 유효계수를 고려하여 산출하였다. 진공용기 이중 벽 내부로 흐르는 질소가스의 유량과 온도의 계산은 진공용기 내벽과 외벽을 각각 독립적인 열전달 요소로 가정하여 구성한 모델을 이용하였다. 전체 해석에서 각 열전달 요소의 비열 값은 온도에 따라 변화하는 비열의 특성을 반영하였으며. 진공용기와 플라즈마 대향 부품의 방사율(emissivity)은 앞서 가정했던 각 온도 상승 곡선에 대해서 각각 0.1, 0.2, 1.3의 경우를 가정하여 계산하였다. 직선적으로 증가하는 온도 상승 곡선중 2$0^{\circ}C$/hr의 온도상승율을 갖는 경우가 다른 베이킹 시나리오 모델에 비해 효과적이라 생각되며 초대 필요 공급열량은 200kW 정도로 산출되었다. 실질적인 수치를 얻기 위해 보다 고차원 모델로의 해석이 필요하리라 생각된다. 끝으로 장기적인 관점에서 KSTAR 장치의 베이킹 계획도 살펴본다.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.43 no.6 s.312
• /
• pp.33-39
• /
• 2006

Trichromatic LED backlight renders higher colour gamut and panel transmittance to the LCDs than the phosphor-converted white LED backlight. In realization, however, several technical challenges arise, such as colour shift, due to the ambient temperature change, brightness decrease along with the temperature increase, colour mixing, minimizing the total number of chips and so on. In this paper we designed and tested the low cost temperature compensating circuit, using a thermistor as a temperature compensating element, for stabilizing the brightness and maintaining the colour coordinates of the trichromatic backlight units. By applying the temperature compensating circuit, the decrement rate of the brightness and colour shift rate were achieved by 54% and 51% respectively comparing with uncompensated case.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.483-484
• /
• 2008

AC-PDP는 구조적으로 2장의 유리, 유전체, 전극으로 구성된다. AC-PDP의 전기적특성은 유전체의 물성에 크게 좌우된다. AC-PDP의 유전체는 주변 온도와 주파수에 따라 유전율 및 유전손실 특성이 달라지므로 온도와 주파수에 따른 유전물질의 물성변화와 panel의 전기적특성에 대한 연구가 필요하다. 본 논문에서는 온도와 주파수에 따른 AC-PDP내 유전체의 유전율 및 유전손실에 대한 특성에 대해 알아보고 4인치 test 패널을 제작하여 온도와 주파수에 따른 panel의 전기적특성 관계를 살펴보았다.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.1
• /
• pp.66-79
• /
• 2019

The aim of the study is to use the by-products sawdust, formed during sawing and mandarin peel which are agricultural by products. The boards were manufactured by mixing the sawdust and mandarin peel at different mixing ratio and density. In terms of changes in surface temperature of ceramics, we could found that the velocity was fast in the early time of heat transfer until 10 minutes and after that the velocity increased but not very fast. At the elapsed time of 30 minutes, the surface temperature of ceramics increased with the carbonization temperature and rate of mandarin peel addition did not influence the surface temperature. Far - infrared emissivity had no constant tendency in rate of mandarin peel addition, it decreased with increase of carbonization temperature.

• Polymer(Korea)
• /
• v.24 no.3
• /
• pp.287-298
• /
• 2000

In preparing micron-sized monodisperse polystyrene beads by dispersion polymerization, the conversion, and the particle size and its distribution were affected by the reaction temperature, concentration of the monomer, solvent and initiator, molecular weight and concentration of the steric stabilizer, amount of oxygen existing in the reactor, and an appropriate combination of these starting materials. Ethanol as a dispersing agent, styrene as a monomer, PVP as a steric stabilizer, AIBN as an initiator, DVB as a cross-linking agent and toluene as a co-solvent were the basic materials for the synthesis. The reaction rate and the conversion were increased with the reaction temperature and the amount of DVB from 1 to 4%, and the conversion was saturated after 10 hours of the reaction time. The optimum reaction recipe for the preparation of the monodisperse PS beads was 25% styrene monomer, 0.5% DVB, 25% toluene, 10-15% PVP, and 2 and 4% AIBN, thereby, 3.9~4 ${\mu}{\textrm}{m}$ and 3.4~9.3 ${\mu}{\textrm}{m}$ of polystyrene beads, respectively, were successfully synthesized.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.1
• /
• pp.90-95
• /
• 2010

The application of livestock manure to cropland is a practice that has been used for centuries. Agricultural crops can utilize nutrients from manure, and the producer can utilize land for disposal, although in a "sustainable system" the concept is manure utilization and not waste disposal. However, meeting regulatory criteria regarding microbial quality remains an expensive and time consuming process. The purpose of this study was to quantify the level of environmental impact of soil moisture and temperature on fecal coliform (Escherichia coli or E. coli) survival in upland soils for sound application of livestock manure. Samples were collected up to 30 days depending on the given conditions. The inactivation rate of E. coli increased linearly with increased temperature while the inactivation rate gradually decreased with decreased soil moisture level. The overall findings of this study showed that the temperature was the limited factor on E. coli survival in soils over soil moisture content. This study will provide useful and practical guidelines to applicators of soil in deciding appropriate handling and time frames for land application for sustainable agriculture.